Question about 2003 Mitsubishi Lancer

Open Question

How to change a clutch on a 2003 mitsubishi lancer.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
keemo68
  • 1263 Answers

SOURCE: replacing front wheel bearing

those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Posted on Aug 28, 2008

Ad
  • 958 Answers

SOURCE: 2003 Mitsubishi Lancer

basic rules.

1 remove the cable.
2. use the right size socket and insert it to the plug.
3. loosen the plug and clean or replace.
4. tighten it back.
5. do it one at a time. it would be confusing to install the wires back if you pull them at the same time.

tnx 4 using fixya and tnx 4 asking,

drcool

Posted on Oct 21, 2008

Loringh
  • 185 Answers

SOURCE: mitsubishi lancer glx 2003 battery discharge

If you disconnect the ground terminal of the battery can you see any sparks if you touch cable to the - terminal?

If you can, go to the fuse panel by the drivers left knee and remove the fuses one at a time. Each time you remove a fuse touch the battery cable to the - terminal and see if you have a spark.
Doing this will enable you to find the circuit that is drawing the current from the battery.

Hope this helps Good Luck Loringh PS Please leave a rating thks

Posted on Nov 09, 2008

  • 11 Answers

SOURCE: 2003 Mitsubishi Lancer

so u have a CH/CG lancer

you would need to remove the two 10mm bolts from the coil packs and leads and then stick the smaller version of spark plug socket in remove them, bear in mind if u have a mivec motor the spark plugs MUST be Platinum :)

Posted on Jan 02, 2009

  • 10 Answers

SOURCE: I have no heat in my 2003 Mitsubishi Lancer. When

thermastat or heater control switch

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 mitsubishi Lancer manual oz rally edition and I'm having trouble switching gears, like it's hard. Any idea what this might be?


If the shifter moves freely when engine is off. Its possible that the clutch is not fully dis-engaging causing stiff gear changes. May be time for a clutch

Apr 04, 2015 | 2002 Mitsubishi Lancer

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

1 Answer

Clutch goes to floor 03 lancer


put fluid back in the clutch master!

Nov 09, 2010 | 2003 Mitsubishi Lancer

1 Answer

Firing order


2003 Mitsubishi Lancer 2.0 liter SOHC L4
and
2003 Mitsubishi Lancer Evolution 2.0 liter DOHC Turbo L4

aebcb80.gif

Hope helps.

Jul 31, 2010 | 2002 Mitsubishi Lancer

1 Answer

2003 Mitsubishi Evo VIII - how do I disengage clutch?


Pertaining to disengaging the pull-type clutch from a 6 speed transmission:

Remove the rubber access plug from the front/bottom of the bellhousing. Insert a long flat head screwdriver into the opening to reach the pull collar at the pressure plate. Once behind the collar, twist the flat head screwdriver to pop the collar off the pressure plate.

ANY other method of removal will damage the ring and or the pressure plate.

Be certain during reassembly that you do NOT hit these components or damage may occur.

Mar 28, 2009 | 2003 Mitsubishi Lancer

1 Answer

2006 mitsubishi lancer evo ix clutch


there are special tools needed that only dealers and some trans shops will have.Definitely a no-no for back yard mechanic

Jan 26, 2009 | 2006 Mitsubishi Lancer Evolution

2 Answers

2003 Mitsubishi Lancer


so u have a CH/CG lancer

you would need to remove the two 10mm bolts from the coil packs and leads and then stick the smaller version of spark plug socket in remove them, bear in mind if u have a mivec motor the spark plugs MUST be Platinum :)

Oct 21, 2008 | 2003 Mitsubishi Lancer

1 Answer

2003 Mitsubishi Lancer


basic rules.

1 remove the cable.
2. use the right size socket and insert it to the plug.
3. loosen the plug and clean or replace.
4. tighten it back.
5. do it one at a time. it would be confusing to install the wires back if you pull them at the same time.

tnx 4 using fixya and tnx 4 asking,

drcool

Oct 21, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
2003 Mitsubishi Lancer Logo

Related Topics:

476 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...