Question about 2001 Chevrolet Blazer

2 Answers

My blinkers have stopped working and my break lights dont work except for the light over the top of the back end. it works when i press the brake. my regular lights work and my high beams work also.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Fix. Turn signals and hazard are on one switch on the dash. Problem is cold solder joints on small board on the switch. First fix I re soldered loose connection on board, worked for a while. Finally simply changed switch with a new one. Take off dash. About 5 screws, pop out hazard switch replace. Problem solved.

Posted on Oct 04, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

We had same problem with our 97 jimmy. It was the multi function turn signal switch.

Posted on Mar 20, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 jeep wrangler 2.5


dont break the brakes..... TURNS & HAZ
many blinker, modules , internally flash with any load.
1: check all fuses first... (SOP)
2: then remove the blinker loads from the timer.

see it here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see WIRING, (end)
8w-51/52
chapter 8w, page 51-4 shows the switch. (complex it is)
note how brake and turns are shared, resources. (blub elements)
now 8w-52-6
see the flasher module.
see C305 pin 2, any load on that pin will cause it to flash.(inside)
that would be any switch in the combo switch stuck on.

Apr 07, 2014 | 1997 Jeep Tj

1 Answer

Break lights and blinkers not working


If you put the tester on the outlets and it lights up properly but the bulbs dont, you have already concluded that the wiring isn't the problem. unless of course the wires are corroded and simply putting the bulb in shorts it out. Have you tested the bulbs?

Jul 22, 2012 | 2008 Pontiac G6

1 Answer

I have a 1990 Mercury Cougar. Several problems...Blinkers, hazards, horn, and break lights are not working. However the break light in the back window comes on when the break is pressed. Checked fused and...


I am unaware of what a "CO" display is.
Now with the blinkers, hazard, horn and brake lights not working that may be the multi funtion switch (blinker switch) that is located inside the column (where the blinker lever attaches).
Obviously the blinker, hazard and horn will all work off of something in the column. Brake lights, you may think a switch on the pedal.

the brake lights do work with that switch but when you have the kind of tail lights where a turn signal light shares the same bulb as a brake light, the brake light is cancelled for the turn signal by running through the multi function switch inside the column.
The third brake light does not blink so its not on that same circuit.

Oct 07, 2011 | 1990 Mercury Cougar

1 Answer

I have a 1988 c1500 chevy truck and my break lights stop working and notice the stop light fuse was missing just bought truck back from previous owner but when I replace the fuse the break light stays on...


The brake light switch on these trucks was a poor design. Its mounted on the brake pedal. Look under there and bend the bracket that holds the brake light switch slightly and things will start working again. When these were new we used to just grab the brake pedal and pull it toward the drivers seat really hard and let go. This fixed your problem 99% of the time.

May 13, 2011 | Chevrolet C1500 Cars & Trucks

1 Answer

Blinkers dont work properly


start by looking for a bad ground to one of the light sockets

Jul 23, 2010 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Brakes Lights dont work on a 2006 Chevy Silverado


I've worked on these the first drove me crazy. its the turn signal switch every thing runs thru these. head lights, turn signal, brakes. except the third brake light. it runs directly from the brake switch. go figuare

Jun 22, 2010 | 2003 Chevrolet Tahoe

2 Answers

1998 S10 rear break lights and blinkers do not work.


If the fuses or brake light switch were bad your third brake light would not work same with the multi purpose switch. you either have a wiring problem like some broken wires or the actual light sockets are bad. it is common with gm trucks that the circuit board for the tail lights melts and does not make contact.

Nov 02, 2009 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...