Question about 1993 Toyota Celica

Open Question

Removing door panels 1993 toyota celica gt - 1993 Toyota Celica

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Opelmanz
  • 62 Answers

SOURCE: door panel toyota

three steps.

1. locate screw holes for door handle (and other areas maybe) and remove. the screws may be located behind plugs that you remove with small flat screw driver
2. disconnect and remove power lock/window unit, usually pries up from one end (rear of car) and slides out. be careful not to stracth leather or upholstry
3. using screwdriver, pry bar, nail bar or other flat piece of metal pry panel away from door one clip at a time. try to pry near the clip, otherwise you risk damaging the panel's interior

post another problem if you get further and still have trouble.

paul

Posted on Oct 26, 2008

  • 170 Answers

SOURCE: 85 Toyota Celica GT Headlights problem

Bad headlight switch or relay, or shorted wire. I would check the relay first.

Posted on Feb 07, 2009

  • 2 Answers

SOURCE: To remove the interior door panel of a 1996 Toyota camry so that

My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
Timmy P.

Posted on Mar 04, 2009

  • 1986 Answers

SOURCE: DOOR PANEL REMOVAL

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 61 Answers

SOURCE: i looking for a fuse box diagram of a 1993 toyota

Try the following URL:

http://www.celicatech.com/imagearchive/bgbonline/93tech/ELECTRIC.PDF

Good luck!

I Can Fix It

Posted on Aug 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 1993 Toyota Celica gt think securty system is locked now no spark to distributer.


you may have to use a code reader to reset the CPU program as flat batteries can corrupt the program and cause starting problems.

Feb 26, 2014 | 1993 Toyota Celica

2 Answers

2000 Celica GT driver door lock


it could be the door lock acuator going bad it could have a intermittent short

Feb 25, 2010 | 2000 Toyota Celica

1 Answer

Replace fog light on a 1993 2.2L Celica GT


The bulb is removed from the back side & the lens is sealed to keep it waterproof and shouldn't be removed.

On most of these, you have to get access from behind, even if it means you have to remove the unit itself, or parts of the car, to gain access to the rear. Once you do, it's an easy replacement.
good luck.

Feb 18, 2010 | 1993 Toyota Celica

1 Answer

How to replace fuel pump for 93 toyota celica gt


Drain the tank and remove it from the car. Note carefully the position of the hoses and wires going to it. Clean the top of the tank well and dry it. Using a non-metallic tool remove the lock ring holding the tank unit in. Carefully lift out the assembly - there are several items connected. Remove the old pump and filter. Installation is just the reverse.

Jan 15, 2010 | 1993 Toyota Celica

1 Answer

Door panel removal How do I remove the drivers door panel? I am having a problem with the door latch mechanism


on my 2000 echo there are horseswhoe spings on door and window crank latches between the handle and the inside panel if yours is same all you need is to insert a small flat screwdrivew on one side of the clamp and pshi it down the caamps are horseshoe shaped wioth a small piece of them sticking out from the door you should be able to remove them by prying on one side and [pushing down at same time after you remove both handlers door panel should pull off you may have to replace a few of the plastic locking screw b 4 you put panel back on

Dec 23, 2009 | 1993 Toyota Celica

1 Answer

Trying to remove door panel 91 celica


Remove all screws that hold on panel, window crank, anything that attaches to door. Then usually along the bottom of the door are plastic parts that are attached to the door panel and then push into hole on metal door. Use a screwdriver to pry the plastic parts out of the metal door. Some will proably break. You can get new one at auto parts store. After you remove all this panel should come right off or you may need to raise the panel straight up because the door panel may be hooked over the metal door.

Aug 07, 2009 | 1993 Toyota Corolla

1 Answer

Toyota Celica


Take the door panel off. There are plastic snaps holding the rods into the lock that need to be unsnapped and pivoted. Then the rods just pull out. The rest is just held on by bolts.

Oct 21, 2008 | 1990 Toyota Celica

Not finding what you are looking for?
1993 Toyota Celica Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...