Question about GMC Sierra 1500

1 Answer

The clutch in my 1995 GMC Sierra 1500 2WD with 5.0 will not fully disengage. I cannot get the truck in or out of gear. I beleive this is my slave cylinder but i wanted to make sure its not a problem with the clutch master cylinder before i spend the money on a new part. The master cylinder has plenty of fluid in the resevoir. Do I just need to go ahead and replace the slave cylinder/

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 17,129 Answers

While the car is parked /switched off are you able to slip in the gears easily ? if so the fault is as you have confirmed of the clutch not able to disengage the transmission drive when the engine starts.
Now to confirm if this is the slave or the master the hydralics must be checked, check to see the movement of the slave, see that the system is bled and there is pressure in the system, make sure there is no leak or spongy feeling., if so it will be good to open and check the system to confrim without deciding to change with a blind feeling. In this case an overhauling of the system will be enough with the repair kit or the slave unit if found to leak.
So before you just go ahead please check to confirm

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

1 Answer

I have a 1994 Isuzu Rodeo 5 speed V6 3.2L, it'll


Sounds like clutch adjustment or replacement. (Not disengaging the trans fully). Check to make sure you have enough juice in the clutch master reservoir and that there isn't a leak at the clutch slave cylinder first.........

Sep 13, 2013 | Cars & Trucks

1 Answer

4wheel drive will not go into any gears 5speed


do you mean the 5 speed manual transmission will not go into gear? and it is a 4x4 truck? I would check clutch linkage and fork or slave cylinder if it applies to this model. Is it grinding at all? Can you determine if the pressure plate is actually disengaging the cluch plate. If the pressure plate is properly disengaging then the problem may be the shift fork in trans is broke,wedged. trans mainshaft broke, I'm not sure but does that year have a removable floor pan cover under floor mat above trans? AS you can pull the top off trans and inspect without pulling trans out of truck.

Feb 08, 2011 | 1995 GMC Sierra C1500

1 Answer

I press my clutch and get no resistance and cant get into any gear? 2003 gmc sierra 8.1 4x4 2500hd 5 speed


Check fluid level in clutch master cylinder, if fluid is full then bleed clutch system.

If you still have no pedal resistance you will need a new master or slave cylinder for the clutch.

1c6f931.jpg

Oct 30, 2009 | 2003 GMC Sierra 2500HD

1 Answer

Gears grinding when trying to shift in a gmc 3500.


some aftermarket masters don't push enough fluid to the slave to disengage the clutch even from the same maker

Sep 04, 2009 | 1985 GMC K3500

3 Answers

1995 GMC Sierra Clutch


either the clutch master cylinder went bad or the clutch slave went bad. look for dripping fluid

Apr 19, 2009 | 1995 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...