Question about Dodge Dakota

Open Question

Trying to bleed the slave cylinder on a 1998 dakota and cant remove the fitting off the slave cylinder

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 275 Answers

SOURCE: Bleeding clutch slave cylinder

if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

Ad
autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

  • 2 Answers

SOURCE: PEUGEOT 406 LX DT 1998 2088 CC CLUTCH SLAVE CYLINDER

I understand these cars have a sealed clutch system. When they fail you replace the whole kit master,hydrolic pipe and slave (comes in one piece). Search on ebay maybe £45 or so.

Posted on Feb 26, 2009

  • 190 Answers

SOURCE: How do I bleed the clutch slave cylinder on a 1993

should be self bleeding if pedal is set correct

pedal rod needs 1/8" free play to clutch master clydinder plunger

fill clutch res slowly let bubbles bleed

then only half strokes on the clutch pedal with 30sec pause between pumps

Posted on Mar 19, 2009

  • 2187 Answers

SOURCE: Bleeding Clutch Cylinder with no bleeder screw

I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced throw out bearings on 1996 dodge Dakota/ v6,do i bleed clutch also,if so how.


if the slave cylinder remaine intact on the hose from the master cylinder then there is no need to bleed the system
if the slave cylinder was inside the bell housing and you ahd to remove a hose to get the box out then yes it has to be bled and by the bleed niple on the sode of the bell housding
bleeding procedure is as per any hydraulic system

Jul 07, 2015 | Dodge Cars & Trucks

1 Answer

Slave cylinder is bleeding off 02 dodge Dakota sxt


It could be. Does either one drip? If not you might the Master Cylinder of the Clutch may be the only one to be in the need to replace. But it is a better choice to replace both. Some of the slave cylinders are a donut type that is built into the throw out bearing. That is a chore.

Feb 04, 2013 | Dodge Dakota Cars & Trucks

1 Answer

Bought new clutch new slave new master still no pressure on pedal how do you bleed the clutch


Hydraulic clutch systems are renown for having airlocks in them once the fluid has drained out.
1.With the Master cylinder full have an assistant pump the clutch pedal acouple of times and keep it on the floor.
2. Release the bleed nipple on the slave cylinder to allow the air out and then tighten.
3. Assistant then allows pedal to come up.They may need to pull back pedal if it does not return by itself.
4.Repeat from #1 until no nore bubbles are seen coming out of the slave cylinder bleed nipple.
If you have a length of suitable size plastic tube that fits neatly over the the slave cylinder bleed nipple , the bubbles will be seen more clearly.
It could thae 8 to 10 pump sequences to clear the air lock. If the clutch still feels spongy, repeat the sequence after a couple of days driving.

Aug 18, 2010 | 1998 Dodge Dakota

1 Answer

No clutch pedal has new master cylinder & slave cylinder still no pedal.


You have air in your hydraulic line. Needs bleeding. If it uses one,
make sure that you used a new crush washer where the line attaches to the slave. Tie a rope around the pedal and use that to pull it back out after pressing down. Makes the process a bit easier on your assistant.

Jul 06, 2010 | 1998 Dodge Dakota

1 Answer

How to replace cluch fluid in mitsubishi triton 1998 ute?


On the slave cylinder will be a bleed port, remove this fitting (port), remove the fill cap and let the fluid drain into a pan, will not take long if you help by pushing on the clutch pedal a few times.

Jan 24, 2010 | 1998 Mitsubishi Eclipse

1 Answer

Replaced master cylinder and cant get air to bleed out


If you have been bleeding it correctly(it is bled using same procedure as brakes just with the clutch pedal) you might need the clutch slave cylinder. It does take a good couple hours to bleed one of these using the conventional two person method so it could still need bleeding but if it is taking to long and your initial symptoms were brake fluid disappearing and you could not visually see the leak from a line or master cylinder then it is leaking from the clutch slave cylinder located in between the clutch and transmission. The transmission would have to be removed.

Oct 29, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Wher i s slave cylinder loc ated on 1998 doge


inside the bellhousing it is a slave and clutch bearing release collar all in one...

Oct 24, 2009 | 1998 Dodge Dakota

1 Answer

Fitted new clutch and slave cylinder in 2.5 v6


crawl up under the dashboard & look where the clutch pedal rod goes through the firewall. look for traces of brake fluid at the rubber boot of the rod. a clutch master cylinder normally will leak to the inside of the vehicle & down the firewall when it fails. Replace as required & bleed clutch system using the bleeder valve that should be on the slave asy.

Oct 15, 2009 | 1998 Ford Contour

1 Answer

Hyd. Slave cylinder WITHOUT bleeder


you have to replace the master and slave. if there is no bleeder, you might get lucky bench bleeding it, but the whole assy, comes from dealer pre-bled. The system is sealed and even to do a clutch or trans, you shouldnt have to take it apart. DO NOT PUSH CLUTCH WITHOUT ALL PARTS HOOKED UP! youll break it.

Mar 21, 2009 | 1999 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...