Question about Chevrolet S 10

1 Answer

How do I ajust my A/C clutch for my A/C in my s10?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,122 Answers

You don't....If your belt squeels, tighten the belt, don't even try to mess with the clutch

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust a 1996 Mazda 121's clutch cable please?


Hi im not familer with this model,but if it is a cable the adjustment will be where the cable gose into the gearbox bellhousing,if there is not a ajuster there then it could be that the clutch pedle has a ratchet that selth ajusts as the clutch wheres down wich means im sorry to say you will need a new clutch,best of luck I hope its the first one.

Aug 08, 2015 | Mazda Cars & Trucks

1 Answer

Ajust the clutch on a nissannote n_tec 1.4 09 can't see any ajuster


most modern cars do not have an ability to adjust the clutch rod in the slave cylinder
if it is slipping then it most likely be a blocked compensating port on the clutch master cylinder holding the pressure plate off
If it is going too far down or only coming up a bit to engage then there is probably air in the system that needs to be led out.
before you waste money pulling the box to replace the clutch ,have it diagnosed at an accredited clutch specialist shop

Feb 25, 2015 | Cars & Trucks

1 Answer

Clutch is sleping can it be ajustment.is there do it your self ajusting that will help


Adjustments- if any- are for the throw out bearing
to pressure plate clearance

No adjustment will fix slipping

You may need the flywheel machined & a new
clutch disc & pressure plate

Mar 09, 2013 | 1993 Honda Accord

1 Answer

How to ajust the clucth


If you have a metal cable going to your clutch slave cylinder which is mounted on the gearbox bell housing (widest part of the gearbox) there is an adjuster on it. If there is only a hydlaulic pipe going to the slave cylinder then I'm afraid there is no adjustment to be made on your clutch, so, it needs either a new clutch or you have an oil leak onto you clutch pad which needs attending to, so, it's a trip to the local shop.

Oct 11, 2012 | 1998 Nissan Frontier

1 Answer

I have a1996 toyota tacoma,when pushing in the clutch at a stop light it made a grabbing sound and was hard to get in gear .By the time I got home I could not get it in gear at all.when egines not running...


YOU NEED TO AJUST THE CLUTCH BLEED AND AJUST MASTER CYLINDER FIRST SAME PROCEDURE AS BLEEDING THE BRAKES FILL THE RESIVOUR ON THE MASTER CYLINDER PUT THE LID ON HAVE SOMEONE PUMP THE CLUTCH CRACK OPEN THE BLEEDER VALVE DO THIS SEVERAL TIMES TO SEE IF THE CLUTCH WILL STIFFIN UP ENOUGH TO OPERATE THE VEHICLE SO THE SLAVE CYLINDER WORK`S RIGHT;,IF THAT DO`SNT HELP DO THIS AJUST THE SLAVE CYLINDER FIRST IT IS DOWN ON THE TRANSMISSION IT PUSHES THE ARM ATTACHED TO THE THROUGH OUT BEARING IF THERE IS NO AJUSTMENT LEFT PUT A 7/16 - 1/2 INCH NUT BETWEEN SLAVE CYLINDER PUSH ROD AND THE THROUGH OUT BEARING PUSH ROD ARM I HAVE DONE THIS AND GOT BY FOR YEARS IF NOT YOU WILL HAVE TO REPLACE CLUTCH PRESSURE PLATE AND THROUGH OUT BEARING ITS JUST GOING TO BUY YOU 10-20,000 MORE MILES ACCORDING TO HOW HARD YOU DRIVE IT DUMPPING THE CLUCTH WILL KILL IT! FIND A NUT THAT THE SLAVE CYLINDER PUSH ROD WILL JUST RECESS IN TO NOT GO ALL THE WAY THROUGH IT GIVES YOU THE WIDTH OF THE NUT MORE AJUSTMENT MOST OF THE TIME THAT IS ALL YOU NEED. IT HAS WORKED FOR ME ON EVERY VEHICLE WITH A WORNOUT CLUTCH!?

Aug 30, 2011 | 1998 Toyota Tacoma

1 Answer

Feels like my manual five speed slips in fifth gear going less than 70


Your clutch plate is probably worn.
You could try to ajust the clutch pressure plate to compensate for this (consult repair manual or get a mechanic to do it for you: should be relatively cheap and fast!) but it could be worned beyond ajustment range and would need replacing.

Dec 25, 2009 | 2001 Ford Mustang

1 Answer

After traveling about 8km my car wont go into 1st or reverse gear. when it is cold it goes into all the gears fine. when i switch the car off it will go into gear. we did put a new(aftermarket clutch) in a...


Cluth cable ajustment if equiped.Some cars have a cluth cylender if your model has the cylender no ajustment is available.If you had your cluth changed at a garage you might consider takeing it back in for ajustments.If you changed the clutch check cluth cable for ajustment if your car is equiped with cable if not i would perhaps remove the transmission and inspect clutch for loose clutch plate or release bearing might not be seated properly hope this helped you.

Dec 24, 2009 | Mazda 323 Cars & Trucks

3 Answers

Clutch fluid weight 1988 chevy s10


in the trans is 80w-90. the clutch fluid is actally the exact same as dot3 brake fluid.

Dec 05, 2009 | 1988 Chevrolet S-10

1 Answer

How to adjust the clutch


hi are you talking about ajustment of free play if so the ajustment is via the cable end located at the clutch fork there are two nuts slacken one and tighten up on the outher one that is the only ajustment outherwise you have a worn clutch and you have to replace it please rate my answer thanks

Nov 20, 2009 | 1999 Subaru Legacy

2 Answers

1986 Chevy S10 Blazer Clutch out or just need to drain and refil?


check the fluid level in the clutch resorvoir if its low fill it up and see if that helps then check for leaking fluid on back side of clutch cylinder and under dash where the clutch pedal attaches to the cylinder next to firewall

Jul 28, 2009 | 1985 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...