Question about 1994 Toyota Camry

1 Answer

Tail lights and brake lights dont work - 1994 Toyota Camry

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 22,095 Answers

Check the bulbs first??

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both tail lights don't work turn signal and back up lights work but no stop light and no tail lights


could be a glitch in the front power controll modual disconect the battery wait couple minuts reconect and see if thay come back
also replace the bulbs even the one on the cab your therd brake light alot of ppl dont relise its out and it will help determin if its in the tail lights or its in the brake switch if the therd brake light lights and the tails dont replcae the switch after inspecting the tail light conectores for corotion

Mar 11, 2014 | 2005 Dodge Ram

1 Answer

How do i remove the sensor for the rear tailgate?


1) Locate and remove sensor.
The sensor is located under the drivers tail light. Unclip it from the body and then unplug it.

2) Bypass the tail light circuit.
Connect the tail light signal wire (Green) to the tail light wire (Green w/ Red Stripe). I recommend using wire tap in squeeze connectors that way you dont have to cut any wires.

3) Bypass the brake light circuit.
Connect the brakelight signal wire (Green w/ White Stripe) to the brake light wire (Red w/ Blue stripe) and the the 3rd brake light wire (Red w/ White Stripe). Again all three of these wires are to be connected together.

4) Throw away your broken Tail Lamp Failure Sensor
Do not plug your sensor back in. Doing so will cause the annoying orange lamp failure warning light on your dash to stay on. Leave it unplugged ant the light will stay off.

5) Test your work
Turn on your lights and make sure your tail lights work properly. Have a friend step on the brake pedal, and make sure your brake lights work properly as well. Dont forget to check the Third brake light.

Sep 20, 2012 | 2002 Chrysler Voyager

1 Answer

1996 chevrolet 1500 brake light and blinkers dont work


a bad turn signal switch the brake lights go threw the turn signal switch

Aug 26, 2012 | 1996 Chevrolet C1500

1 Answer

All my lamp indicator lights keep flashing. blickers work. when you step on break the break lights work. but when driving no tail lights


First replace the tail light bulbs. The tail light and brake lights are different filaments in the same bulb. it is very possible for the tail lights to go out while brake lights still work. And somtimes the tail lights can blow out together.
If you change the bulbs and still dont work then look for other problems.

May 22, 2011 | 1992 Buick Park Avenue

1 Answer

On 2002 jeep laredo brake lights dont turn on if lights arent on


That does not make any sense. Do the tail lights work? There are supposed to be separate filaments for brake lights, tail lights, and turn signals. In particular the center brake light should not be possible to be confused with tail lights or signals. Does it come on? If not, then you probably have no brake lights at all, and that is probably because of the bad fuse or the switch on the brake pedal for the brake lights.
If there is some sort of cross over between tail light and brake lights, that is usually from a bad light socket ground; which results in current backing up from one system to another. But then each is usually only half brightness.

Jul 20, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Tail lights dont work


Replace the bulbs.
The bulbs will have two seperate elements in it which is why the brake light works.

Take the bulbs out and you will see the seperate elements.

Jan 08, 2009 | 1995 Subaru Impreza

2 Answers

My tail lights dont work, its not a fuse, my blinkers and reverse lights work, its just my running lights and my brake lights that dont, any suggestions?


check the wire harness that runs from inside the trunk on the drivers side follow it down to the tail light and make shure the wires are not damaged or unplugged remove cover on the drivers side inspect the bulbs the holders and the wires and dont forgt to retighten all grounds that you find on your travels this should get the rear tail lights working also check the brake pedal switch up on the metal part of the brake pedal arm follow it up tp the brake pedal switch and acuate the switch by hand and check the wire voltage coming in and going out when pressing the brake pedal ok give this a shot

Jul 21, 2008 | Ford Mustang Cars & Trucks

Not finding what you are looking for?
1994 Toyota Camry Logo

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...