Question about 2002 Toyota Land Cruiser

1 Answer

Does the computer need reset after bursting power steer line , replaced line but still no power assist even after bleeding

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 104 Answers

The computer doesn't sense the power steering.You should have the power steering pump looked at and possibly replaced as well as having the rack and pinion checked out.

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake and abs light on,came on when a line burst,abs has been unplugged for three years,that light i can live with,the service brake system flashing on dash,is a pain,2003 2wd,silverada


You need to put a scanner on the ecm/computer for the truck and reset or delete the code in the computer. This is all assuming the broken line has been fixed and the lines bleed. The abs light is for the brake system and there is a valve in the line that when the line breaks it shuts off the line in the front or rear of the truck that has a break in it. You need to be sure the valve is shifted to the center position again and this will usually happen when you bleed the fluid after fixing the line or you will need to replace the valve in the brake line. Hope this helps.

Nov 28, 2015 | 2003 Chevrolet Silverado 1500

2 Answers

Why does my van's power steering fluid leak out as quickly as added if the van is running?


Burst power steering hose.
Cracked power steering hard line.
Bad seal in power steering pump.
Lose fittings on power steering lines.
Check power steering components for signs of leaking fluid.

Apr 11, 2015 | Cars & Trucks

1 Answer

I keep bursting rack & pinion boots, does that mean my power steering pump is bad


no, if you have power steering fluid leaking into the boot it means your power steering piston/rod/cylinder has leaking seals.
replace the cylinder (what you attached the boots to) or rebuild the packing.

Jan 03, 2015 | Chrysler Pacifica Cars & Trucks

1 Answer

Repair shop said steering pump expolded on our 2000 Volvo XC V 70


never heard of the pump exploding... bursting one of the high pressure lines is more likely. new belt afterwards? sure. new battery? dont see how it could have harmed the battery. new tie rod? no way did this damage a tie rod.

replacing burst high pressure line 75.00 for parts
replacing belt 15.00 for parts
replacing power steering pump if needed no more than 150.00 for parts. thats 240.00 for parts... for the sake of argument lets double that for labor. 480.00

replace tie rod (in no way damaged by power steering pump) 35.00 to 125.00 depending on where you get it. installation cost about 75.00 (Tie rods can most often be adjusted to correct problem without having to replace them.
now, new battery (probably not related to the burst line) anywhere from 40.00 to 200.00 from autozone with free installation.

Feb 11, 2014 | 2003 Volvo XC70

1 Answer

Power Steering Bleeding


no theres not it beeds itself replace pump

Jul 07, 2013 | Cars & Trucks

1 Answer

Bleed power steering on 2008 dodge avenger


to bleed power steering, with front wheels off ground slightly with front wheels pointing straight ahead.engine off. remove power steering filler cap.add power steering until fluid level stop dropping,wait couple minutes and wait, add fluid until level stay at full cold mark on power steering cap dip stick. dont over fill.when fluid level stop dropping, start vechicle,let it idle few minutes. see if fluid level drop if so add more fluid full cold mark.then turn steering all the way to left and right with out hitting a stop.turn steering wheel several times, then turn front wheels pointing forward check power steering fluid level.if power steering fluid level stop dropping air should be out of system, if steering turning wheel dont turn smoothly and power steering fluid look light tan color air getting in the system.check all power steering lines to rack and power steering pump for leaks.be sure you replaced all the power steering lines with new o rings if not you will get a leak.if you find a leak, you need to fix the leak and bleed system again.dont drive vechicle if your steering dont feel right,have vechicle towed to a garage.

Aug 25, 2012 | 2008 Dodge Avenger

1 Answer

Having trouble bleeding my power steering pump. I opened the line while replacing the left engine mount and got air in the line. I tried the manual proceedures with no success.


There is no need to bleed the line your stating power steering pump just add steering fluid and keep it at the appriopriate level and it bleeds it self

May 24, 2011 | 1993 Eagle Talon

1 Answer

Bleeding the power assist system


you have a vaccum leak or the brake booster diaghram is damged!
check all vaccum hoses but i bet its the booster! get it done ASAP!!
Cheers rob.

Jul 28, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

Power steering - 1999 chevy silverado


You're going to have to bleed the system alot on those trucks. Just remove the return line and have an assistant turn the steering wheel back and forth just enough to engage the pump and filling the resevour while doing this. Keep bleeding until you have a good flow of P/S fluid out with no air bubbles. This can take a while.

Aug 24, 2008 | 1999 Chevrolet K1500

Not finding what you are looking for?
2002 Toyota Land Cruiser Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...