Question about 2005 Jeep Grand Cherokee

1 Answer

Remove starter 2005 chrokee limited 5.7. Does it involve removing header. Or heat shield or neither?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Both

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located


Hi, the Kia Sedona starter (and all other major parts) are the same from 2000 to 2005. Here is a link with your starter location and how to remove it:
http://www.kia-forums.com/kia-carnival-sedona/84617-starter-problem-sedona-2003-help.html

In this pic you can see the starter's location (hidden behind the exhaust heat shield):79720193-778a-42e2-b4ff-a2d753f3adce.jpg

May 30, 2014 | 2005 Kia Sedona

1 Answer

Removing starter nissan pick up 4 cylinder engine


Okay , i will give you step by step, the book calls for .9 for time.
1) First remove the front right tire.
2) Remove neg battery terminal.
3) Remove starter wiring.
4) Remove the right front splash shield.
5) Remove the exhaust manifold heat shield.
6) Remove the exhaust manifold.
7) Remove the oil filter.
8) Remove the oil sender connector.
9) Remove the starter bolts and remove starter from cylinder head side.

Hope this helps, let me know how it goes, good day.

Dec 24, 2012 | 1991 Nissan Pickup

1 Answer

How do i change the starter on 2005 kia optima


The starter and solenoid is located behind two separate aluminum heat shields right directly behind the exhaust manifold. (The exhaust manifold is right in back of the radiator. Take off both heat shields, then remove the two bolts that hold the starter. I disconnected one of the wire harnesses that was in the way to give me more room to work. Don't forget to disconnect the battery terminal before starting the project as you will need to remove the positive terminal on the solenoid to remove the assembly from the vehicle.

Nov 29, 2011 | 2005 Kia Optima

1 Answer

How do you remove a starter on a 1997 GMC Jimmy?


1995-97 4.3L MODELS and 1995-99 2.2L models

5ed4c74.jpg

Fig. 5: The starter motor on later model 4.3L engines is retained by two long bolts
  1. Disconnect the negative battery cable.
  2. Raise and support the front of the truck safely using jackstands.
  3. If necessary for access, disconnect the front exhaust pipe.
  4. If equipped, remove the starter heat shield.
  5. On the 2.2L engine, remove the brace rod from the front of the engine and the bell housing.
  6. On 2.2L engines, remove the drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well.
  7. Disengage the wires from the starter solenoid.
  8. On the 2.2L engine, remove the attaching bracket-to-engine mount bolt.
  9. Remove the starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
  10. Carefully lower the starter and shims (if equipped) from the vehicle.
  11. If necessary, remove the bracket (2.2L engine) or the shield (4.3L engine) from the starter assembly.
To install:
  1. If removed, install the bracket or shield to the starter, as applicable. Tighten the bracket nuts to 97 inch lbs. (11 Nm) or the shield nuts to 106 inch lbs. (12 Nm).
  2. Carefully raise the starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
  3. On the 2.2L engine, loosely install the bracket-to-engine mount bolt.
  4. Install the remaining starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm).
  5. Engage the wiring to the solenoid as noted during removal.
  6. On the 2.2L engine, install the brace rod and tighten the retainers.
  7. If disconnected for access, install the front exhaust pipe and tighten the fasteners.
  8. If equipped, install the starter heat shield.
  9. On 2.2L engines, install the drivers side wheel.
  10. Remove the jackstands and carefully lower the truck.
  11. Connect the negative battery cable.

Hope helps.

Sep 07, 2010 | 1997 GMC Jimmy

1 Answer

How do you replace the starter on a 2004 Hyundai XG350L?


Step 1. Disconnect the negative battery cable.
Step 2. Remove the heat shield protecting the starter from the heat of the LH exhaust manifold
Step 3. Disconnect the wire to the starter solenoid
Step 4. Disconnect the battery cable at the starter (12mm nut)
Step 5. Remove the two 14mm bolts which attact the starter to the transmission bell housing & remove the starter.
Reassembly is in reverse order.

Aug 21, 2010 | 2004 Hyundai XG350

1 Answer

How do you remove the engine starter???


1. Disconnect the cable from negative battery terminal.
2. Raisew vehicle and support it securely on jackstands.
3. If the starter has a heat shield, remove it. Remove the protective plastic cap and disconnect the wirring from terminals on the starter solenoid.
4. Remove the starter motor mounting bolts and detach the starter from the engine.
5. Installation is the reverse of removal.
Tourque teh starter bolts to 18ft-lbs

Feb 20, 2010 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

Need to know how to remove starter from 1991 dodge caravan


e
26065b4.jpg

Starter motor mounting-2.2L and 2.5L engines

- Working from under the vehicle, disconnect the starter motor heat shield clamp

fb70ec4.jpg

View of the starter motor with the heat shield removed while looking over the crossmember

-
Removing the starter motor mounting stud nut where the air pump tube bracket is also attached

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle. The starter can be removed by reaching over the crossmember.
  3. Remove the heat shield and its clamps, if so equipped.
  4. On the 2.2L and 2.5L engines, loosen the air pump tube at the exhaust manifold and move the tube bracket away from the starter.
  5. Remove the electrical connections from the starter.
  6. Remove the bolts attaching the starter to the flywheel housing and the rear bracket to the engine or transaxle.
  7. Remove the starter from the engine.

To install:
  1. Position the replacement starter against the mounting surface.
  2. Install the mounting bolts.
  3. Connect the starter wiring.
  4. On 2.2L and 2.5L engines, position the air pump tube toward the starter, then connect the tube bracket to the exhaust manifold.
  5. Install the heat shield and clamp.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1991 Dodge Caravan

1 Answer

My 2005 Corolla XRS has rattling when deaccelerating


I wouldn't say it is common. There are quite a few heat shields around the stock exhaust "header" and exhaust system. There are also FOUR motor mounts that you can check to see if all bolts are tight. They are all 14mm heads on the motor mounts, 12mm on the exhaust shields. These seem to be the main things that may get loose or make a rattling sound. The exhaust gasket is also designed to flex when the engine flexes - I would check into the exhaust. You have to remove the TRD strut bar to gain better access from above.

Aug 13, 2009 | 2005 Toyota Corolla

1 Answer

Removing starter heat shield on 2000 Passat 4cyl Turbo


I am not sure if I have the right engine but this may help and give you a better idea of what you are doing.

2-Wheel Drive (2wd) Models (2wd) Models
2.2L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • Front exhaust pipe, if necessary for access
    • Starter heat shield, if equipped
    • Brace rod from the front of the engine and the bell housing
    • Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well
    • Wires from the starter solenoid
    • Attaching bracket-to-engine mount bolt
    • Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you.
    • Starter and shims (if equipped) from the vehicle
    • Bracket from the starter assembly, if equipped 0900c15280096824.jpgStarter motor and related components—2.2L engine
To install:
  1. Install or connect the following:
    • Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm).
    • Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position.
    • Bracket-to-engine mount bolt (loosely), if equipped
    • Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm)
    • Wiring to the solenoid
    • Brace rod and tighten the retainers
    • Front exhaust pipe and tighten the fasteners, if removed
    • Starter heat shield, if equipped
    • Driver’s side wheel, if removed
    • Negative battery cable

Nov 27, 2008 | 1999 Chevrolet Tahoe

2 Answers

Changing the starter on my 99 tahoe


Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
Removal & Installation
4.8L, 5.3L And 6.0L Engines
CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Protective shields, as necessary
    • Starter solenoid shield
    • Starter-to-transmission close out cover bolt
    • Engine oil level sensor connection
    • On 4WD, front axle mounting bracket through bolt nut
  4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
    • Starter transmission close out cover
    • Positive battery cable and wiring harness from the starter
    • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
To install:
  1. Install or connect the following:
    • Starter
    • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
    • Starter transmission close out cover
    • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Engine oil level sensor connection
    • Starter-to-transmission close out cover bolt
    • Starter solenoid shield
    • Protective shields as necessary
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
5.7L And 7.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Mounting bolts and shims
    • Wires
    • Heat shield
    • Starter
To install:
  1. Install or connect the following:
    • Starter
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
    • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
    • Negative battery cable
6.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cables
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Starter
    • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
    • Negative battery cables
8.1L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • On 4WD, front axle mounting bracket through bolt nut
  2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Positive battery cable nut
    • Positive cable from the solenoid
    • Engine harness ground nut and ground from the solenoid
    • Mounting bolts and starter
    • Heat shield bolts, nut and shield, if necessary
To install:
  1. Install or connect the following:
    • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
    • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
    • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
    • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Negative battery cable

Sep 28, 2008 | 1999 Chevrolet Tahoe

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...