Question about 1989 Buick Regal

1 Answer

THE VEHICLE WILL TURN OVER BUT WILL NOT START. 35 LBS ON THE FUEL PUMP.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

If it starts, even if only for 1 second then replace the crank position sensor. The cam postition sensor should be checked as well

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i change the fuel filter on a 2004 hyundia sonata?


NOTEThe fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cableFuel supply and pressure linesFuel filter bracket, if equippedFuel filter

To install:


0996b43f80231741.jpgenlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the fuel filter

  1. Install or connect the following:

    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm)Fuel filter bracket, if equippedFuel supply and pressure linesNegative battery cable
  2. Start the engine, check leaks and repair if necessary.


NOTEThe fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cableFuel supply and pressure linesFuel filter bracket, if equippedFuel filter

To install:

9347kg12.jpgenlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the fuel filter


  1. Install or connect the following:

    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm)Fuel filter bracket, if equippedFuel supply and pressure linesNegative battery cable
  2. Start the engine, check leaks and repair if necessary.


NOTEThe fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cableFuel supply and pressure linesFuel filter bracket, if equippedFuel filter

To install:

9347kg12.jpgenlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the fuel filter


  1. Install or connect the following:

    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm)Fuel filter bracket, if equippedFuel supply and pressure linesNegative battery cable
  2. Start the engine, check leaks and repair if necessary.

icn_arrow.gifBack to Topbuyithere.gif

    Sorry, there are no parts available for the selected vehicle: 2004 Hyundai Sonata 2.7L MFI DOHC 6cyl.

Nov 24, 2012 | Hyundai Motor 2004 Sonata

2 Answers

Vehicle will start but then quickly stalls (within 5 to 10 secs). Fuel pump or fuel filter or?


I would start with the smallest and cheapest first, try replacing the fuel filter ensure it is placed in the direction of fuel flow, then see if that helps out before moving onto the pump.

Feedback appreciated.

Mar 25, 2011 | 1997 Pontiac Grand Prix

1 Answer

What special tools do I need to remove the fuel tank from my 04 F250 for cleaning ?


Anyone special tool, just check this procedure to Removal & Installation
CAUTION Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    Negative battery cable Fuel pressure Fuel tank skid plate bolts and lower the skid plate. Fuel Fuel tank filler pipe hose from the tank Fuel tank filler pipe vent hose from the tank Fuel lines from the fuel pump Front fuel tank connections Rear Evaporative Emissions (EVAP) hose clamp and the hose Electrical connector from the fuel pump

  3. Support the fuel tank with a jack.
    Fuel tank support strap bolts and the fuel tank straps Fuel tank
To install:
  1. Installation is the reverse of removal. Note the following torques:
    1. Tighten the fuel tank strap bolts to:
      F-150: 35 ft. lbs. (47 Nm) F-250 and F-350 mid-ships tank: 30 ft. lbs. (40 Nm) F-250 and F-350 aft-of-axle tank: 66 ft. lbs. (90 Nm) Mark LT: 35 ft. lbs. (47 Nm)
  2. Tighten the skid plate bolts to:
    F-150: 15 ft. lbs. (20 Nm) F-250 and F-350 mid-ships tank shield: 15 ft. lbs. (20 Nm) F-250 and F-350 aft-of-axle tank cover: 66 ft. lbs. (90 Nm) Mark LT: 15 ft. lbs. (20 Nm)
  3. Connect the negative battery cable.

Hope helps.

Dec 24, 2010 | 2004 Ford F250

1 Answer

Access panel for fuel pump


There is none:

Fuel Tank & Fuel Pump Module Assembly Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Shift the vehicle into NEUTRAL and position it on a hoist.
  3. Release the fuel pressure.
  4. Disconnect the negative battery cable.
  5. Remove the fuel tank filler cap.
  6. Drain as much fuel from the tank as possible.
  7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

  8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
  9. Disconnect the fuel pump electrical connector.
  10. Disconnect the fuel filter inlet tube from the filter.
  11. Position a suitable lifting device under the fuel tank.
  12. Remove the two fuel tank support strap bolts.
  13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
  14. Clean the area around the fuel pump mounting flange.
  15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
    The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
  17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
To Install:
  1. Install the fuel pump module in the fuel tank.
  2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
  4. Connect the fuel lines and electrical connectors at the fuel tank.
  5. Lower the vehicle and refill the tank.
  6. Connect the negative battery cable.
  7. Turn the ignition key to the ON position to pressurize the fuel system.
  8. Visually inspect the fuel system for leaks.
prev.gif next.gif

Oct 05, 2010 | 2000 Ford Taurus

1 Answer

Is there an access hatch in the floor of a 1996 gmc safari for the fuel pump


no, sorry. Here are the R&R instructions from autozone.com:

The following procedure requires the use of the GM Fuel Gauge Sending Unit Retaining Cam tool No. J-24187 or equivalent.


CAUTION Before removing any component of the fuel system, be sure to reduce the fuel pressure in the system. The pressure regulator contains an orifice in the fuel system; when the engine is turned Off, the pressure in the system will bleed down within a few minutes.

  1. If the fuel system has been in use, turn the ignition switch to OFF and allow the system time to reduce the fuel pressure.
  2. Disconnect the negative battery terminal from the battery.

Be sure to keep a Class B (dry chemical) fire extinguisher nearby.


CAUTION Due to the possibility of fire or explosion, never drain or store gasoline in an open container.

  1. Using a hand pump or a siphon hose, drain the gasoline into an approved container.
  2. Raise and support the vehicle on jackstands.
  3. Support the fuel tank and remove the fuel tank-to-vehicle straps.
  4. Lower the tank slightly, then remove the sender unit wires, the hoses and the ground strap.
  5. Remove the fuel tank from the vehicle.
  6. Using the GM Fuel Gauge Sending Unit Retaining Cam tool No. J-24187 (or equivalent) or a brass drift and a hammer, remove the cam locking ring (fuel sending unit) counterclockwise, then lift the sending unit from the fuel tank.
  7. Remove the fuel pump from the fuel sending unit, by performing the following procedures:
    1. Pull the fuel pump up into the mounting tube, while pulling outward (away) from the bottom support.


When removing the fuel pump from the sending unit, be careful not to damage the rubber insulator and the strainer.
    1. When the pump assembly is clear of the bottom support, pull it out of the rubber connector.


To install:
  1. Inspect the fuel pump hose and bottom sound insulator for signs of deterioration, then replace it, if necessary.
  2. Push the fuel pump onto the sending tube.
  3. Using a new sending unit-to-fuel tank O-ring, install the sending unit into the fuel tank.

When installing the sending unit, be careful not to fold or twist the fuel strainer, for it will restrict the fuel flow.
  1. Using the GM Fuel Gauge Sending Unit Retaining Cam tool No. J-24187 (or equivalent) or a brass drift and a hammer, turn the sending unit-to-fuel tank locking ring clockwise.
  2. Install the fuel tank, align the insulator strips and install the strap bolts. Torque the inner fuel tank strap-to-vehicle bolts to 26 ft. lbs. (35 Nm) and the outer fuel tank strap-to-vehicle nuts/bolts to 26 ft. lbs. (35 Nm).
  3. Connect the fuel lines.
  4. Connect the negative battery cable, start the engine and check for leaks.
  5. Lower the vehicle.

Sep 19, 2010 | 1996 GMC Safari

1 Answer

How to change a fuel pump on a 2005 Nissan


Nissan Car Altima & Sentra 1999-06 Repair Guide
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the pressure from the fuel system.
  3. Remove or disconnect the following:
    NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
    Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
    Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
  4. Place a clean rag in the hole to keep out dirt.
To install:
  1. Remove the rag
  2. Install or connect the following:
    NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
    New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
  3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
    Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
  4. Start the engine, check for leaks and repair if necessary.
    Fuel pump access cover Rear seat

The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
  4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
    Fuel gauge assembly Fuel pump with the fuel chamber
  5. Pull up the front of the fuel pump chamber and slide the chamber forward.
    Fuel pump from the chamber O-ring seal or gasket
To install:
  1. Install or connect the following:
    Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

Hope helps (remember comment and rates this).

Jul 07, 2010 | 2005 Nissan Sentra

2 Answers

How to change fuel fillter


2002 Hyundai Sonata 2.4L MFI DOHC 4cyl the Fuel Filter is located uUnder vehicle, driver side, below seating area, driver side of fuel tank, mounted on frame in fuel line.


Hyundai Car 1999-05 - Removal & Installation

NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

d8227e1.jpg

Fig. Remove the fuel filter
  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.

Hope this help to solve your problem.

Apr 24, 2010 | Hyundai Motor 2002 Sonata

1 Answer

How to Change a Fuel Pump in a 2001 Ford Crown Victoria


STEPS TO CHANGE FUEL PUMP
  1. Park the vehicle in a safe place and make sure there is enough room around the back of the vehicle for you to work and move tools around.
  2. Start the engine and let it idle while you relieve the fuel system pressure by removing the fuel pump fuse or relay from the fuse box. Wait a few seconds for the engine to stall, turn the ignition key off and replace the relay or fuse.
  3. Raise the back of your car using a floor jack and support it safely on jack stands.
  4. Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle.
  5. Disconnect the vapor tube from the tee connector on the right side of the car-passenger side-and the vapor line from the canister tube.
  6. Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and lower the fuel tank. Discard the fuel tank mounting studs.
  7. Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.
  8. Clean the area around the fuel pump mounting flange and remove the flange mounting bolts in a crisscross pattern.
  9. Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to 89 inch lbs. (10Nm) using a crisscross pattern.
  10. Raise the fuel tank to its mounting position, install the strap using new mounting studs and torque the nuts to 26 foot lbs. (35 Nm).
  11. Connect the fuel pressure transducer electrical connector, vapor tube to the tee connector, vapor line to the canister tube, fuel tank filler pipe and fuel pump electrical connector.
  12. Lower the vehicle, start the engine and check for leaks.

Nov 22, 2009 | 2001 Ford Crown Victoria

1 Answer

How do i put a fuel pump on a crown victoria 1987 5.0


Hi, this will help you achieve your goal.


Step 1

Park the vehicle in a safe place and make sure there is enough room around the back of the vehicle for you to work and move tools around.

Step 2

Start the engine and let it idle while you relieve the fuel system pressure by removing the fuel pump fuse or relay from the fuse box. Wait a few seconds for the engine to stall, turn the ignition key off and replace the relay or fuse.

Step 3

Raise the back of your car using a floor jack and support it safely on jack stands.

Step 4

Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle.

Step 5

Disconnect the vapor tube from the tee connector on the right side of the car-passenger side-and the vapor line from the canister tube.

Step 6

Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and lower the fuel tank. Discard the fuel tank mounting studs.

Step 7

Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

Step 8

Clean the area around the fuel pump mounting flange and remove the flange mounting bolts in a crisscross pattern.

Step 9

Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to 89 inch lbs. (10Nm) using a crisscross pattern.

Step 10

Raise the fuel tank to its mounting position, install the strap using new mounting studs and torque the nuts to 26 foot lbs. (35 Nm).

Step 11

Connect the fuel pressure transducer electrical connector, vapor tube to the tee connector, vapor line to the canister tube, fuel tank filler pipe and fuel pump electrical connector.

Step 12

Lower the vehicle, start the engine and check for leaks.

Jun 26, 2009 | 1987 Ford Crown Victoria

1 Answer

1989 ford aerostar will not start when engine is warm.


AM temp 55 car started but stalled out after starting. Attempted to restart and did not hear fuel pump. Tried again and then fuel pump kicked in. Checking fuel pump inertial switch and fuel pump electrical supply.

Apr 19, 2009 | 1989 Ford Aerostar Cargo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...