Question about 1993 Buick Century

1 Answer

How do you remove the front corner turn signal unit

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 347 Answers

If you open the hood and look by the lite you want to remove you will see a spring with a finger hole loop on the end of it .you can put your finger in it and pull to release from the lens. the the lens will just pull out ,it has a alignment pin and receiver in the back of it to align and hold in place the back of the lens Hope this Helps

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 subaru forester front tail turn signal bulb replacment


The pic attached shows instructions for the headlight and signal.
for just the signal light start by removing the phillips screw (A) from the tab above the headlight. Without breaking that tab, carefully pry the unit out from the corner start at the fender edge use something thin and plastic like a disposable knife with the teeth smoothed off.. once its out twist then pull out the bulb socket. They usually have markings to show the direction to twist. The bulbs are mostly the glass press in type which click when installed fully.

Nov 22, 2016 | 1999 Subaru Forester

1 Answer

How do I get to turn signal bulb on right front of 1990 buick century


open hood look for the light assembley powercords that go into the headlamp..turn right or left to loosen ... you may have to just take a screw driver and remove the cover over the signal light. press in and turn and replace.

Mar 08, 2015 | 1990 Buick Century

1 Answer

How do I replace the left front turn signal lamp on a 2002 Porsche Carrera Cabriolet?


Hello sdangus
In your Porsche tool kit is a little pipe-wrench which is for removing the headlights.
In your trunk remove the front corner carpet and you will see a black plastic plug(remove it).Behind is a screw for which is the tool for.Turn counterclockwise to release the headlight.
Replace what ever you need and then reverse the motion to install the headlight unit back to its place.I hope this will help you?

proporsche

Jan 15, 2011 | Porsche Carrera Cars & Trucks

1 Answer

Trying to replace front turn signal in 2001 chevy cavalier I removed splash panel but cannot get to turn signal bulb - can you help


to replace the the turn signal and headlamp bulbs, you need to pull the lights out from the front

to do so first you'll have to remove the plastic cover that spans over the radiator (there should be 6 push-in plastic clips holding it in, I use a wire crimping tool, but a couple flat screwdrivers or pliers if careful can work as well)

now, if it's just the cornering lamp that you need, then a large screwdriver or small pry-bar can be used to pop the lamp out

To see where to pry it helps to have a flashlight and look between the headlamp and cornering lamp, there's a clip that holds it in place, just pry against the clip [towards the center of the car, be firm as it is stiff, but if you just yank it, it may brake as it's plastic]

The clip should be around (though below) where the tip of the fender ends. The corner lamp should just pop out with enough prying

For future reference, replacing the headlamp bulbs you get to this point then remove the 2 bolts you can see the brackets the headlamps are mounted to, and they should then come out

Aug 03, 2010 | 2001 Chevrolet Cavalier

1 Answer

How do I replace the passenger side corner light and front side turn signal light?


Front Turn Signal & Parking Lights


7ccc73e.gif
Remove the 2 parking light housing retaining screws ...


9898a80.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull


a323ae9.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb


  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.


Side Marker Lights
  1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
  2. Pull the bulb from its socket in the back of the lens.
  3. Installation is the reverse of removal.

Feb 14, 2010 | 1997 Jeep Grand Cherokee

1 Answer

Change front turn signal light?


Front Turn Signal & Parking Lights
  1. On some models you will need to remove the headlight bezel mounting screws and the bezel.
  2. Remove the mounting screws for the lamp assembly.
c289083.gif
Remove the mounting screws securing the lamp assembly

8325b44.gif
After the screws are removed, pull the assembly from the vehicle

ad45385.gif
Disconnect the twist lock socket from the lens housing
To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1/4 turn, then remove the socket with the bulb; replace the bulb if defective.

19af8c1.gif

Newer Oldsmobile models have the turn signal separate from the headlamp assembly ...

d57d520.gif
... unlike the newer Buicks, where the unit is attached to the headlamp

To install:
  1. Install the electrical harness to the back of the unit.
  2. Position the signal assembly, then attach to the vehicle with the mounting screws. Tighten the screws to 54 inch lbs. (6 Nm).
  3. Insert the socket to the back of the unit, then attach the headlamp bezel if removed.

Oct 31, 2009 | 1990 Pontiac 6000

1 Answer

How do you change the turning signal on ford contour sport?


This is for the 95-97 Contour. 98+ are different, because the light housing changed completely.
1. Open the hood.
2. In each front corner of the hood, there is a torx bolt, head about the size of a nickel. Removing this one bolt allows you to remove the corner marker/turn signal housing.
3. Once the housing is free, you have access to the back of the bulb holder. If I recall correctly, it's a half-twist to remove, but I'm not sure. Could just be barbed clips, or something. Anyway, from here should be no problem to figure out how to remove and replace the bulb.
4. Replace corner marker/turn signal housing, and re-install torx bolt. That's it!

Oct 11, 2009 | 1997 Ford Contour

2 Answers

Signal bulb on 2003 buick regal


To change front turn signal –
open the hood; look in back of headlight; two white clips; pull straight up, and then whole headlight comes out including turn signal; it is all one unit; remove rubber cover, then you take bulb out of unit. Mechanism that bulb fits in will need to be turned clockwise (looking from the front) and pulled to get it out of the larger unit holding all lights. Be sure and put rubber cover back on before re-inserting the two white clips.

Mar 16, 2009 | 2000 Buick LeSabre

1 Answer

Change front turn signal


You have to remove the signal unit from the bumper using a normal " + " screwdriver then twist the bulb holder at the back of the sinal unit.

Nov 23, 2008 | 1991 Honda Accord

1 Answer

Left front turn signal bulb for 2001 Pontiac Montana


There is only one screw to remove that releases the mounting tab at the upper inner corner of the assembly. That screw has a plastic wingnut molded onto it so you can turn by hand. Once that is removed, the assembly can be pulled straight forward. At the inner bottom corner, a spring clip faces straight rearward. Pull with enough force to to release the clip from its slot. Only two "Fingers" hold the rear of the assembly in the sheet metal holes.

Oct 16, 2008 | 2003 Pontiac Montana

Not finding what you are looking for?
1993 Buick Century Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...