Question about 1993 Oldsmobile Cutlass Ciera

1 Answer

How do i replace the waterpump on my 93 cutlass ciera

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 343 Answers

I could walk you thru the steps involved, but the best advice i can give you is to spend about $25 on a manual from your local parts store or online access to a manual. If things are real tight, go to the library and photo copy the section of a GM manual that applies. If this does not help you out the reply to my answer and I will take the time to type out all the steps involved which could be extremely time consuming... MK

Posted on Oct 02, 2010

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 834 Answers

SOURCE: i need to reset the timing on my 93 oldsmobile

You must have an ignition distributor to be able to reset or change the engine timing. If you do have a coil pack then the engine timing is completely controlled by the computer and there is no timing adjustment.

Posted on May 10, 2010

ZJLimited
  • 17970 Answers

SOURCE: 1995 Oldsmobile Cutlass Ciera, replace waterpump

Hi there:
Check this procedure...

2.2L Engine (see Figure 1)
Partially drain the engine coolant from the vehicle.
Remove the serpentine drive belt from the vehicle.
Loosen and position the alternator to one side.
Unbolt the water pump pulley, then remove the pulley.
Unbolt the water pump, then remove the pump and gasket.

12_16_2011_1_35_31_pm.gif

Fig. 1: Water pump used on 2.2L engines

Clean the gasket areas thoroughly.

To install:
Install a new gasket to the water pump mating surface.
Attach the water pump to the engine with the retaining bolts, tighten them to 18 ft. lbs. (25 Nm).
Attach the water pump pulley, then tighten the bolts to 22 ft. lbs. (30 Nm).
Properly position the alternator.
Install the serpentine drive belt.
Fill the coolant system, start the engine, then top off the fluid.


3.1L Engine (VIN M)
Partially drain the coolant from the vehicle.
Remove the serpentine drive belt from the vehicle.
Unbolt the pulley from the pump.
Remove the water pump mounting bolts.
Remove the pump from the engine, then clean the gasket area.

To install:
Attach the water pump with gasket to the engine with the mounting bolts.
Tighten the mounting bolts to 89 inch lbs. (10 Nm).
Attach the pulley with it's mounting bolts. Tighten them to 18 ft. lbs. (25 Nm).
Install the serpentine drive belt.
Fill the coolant system, start the engine and top off the fluid. Check for leaks.


Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Posted on Dec 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What makes the fuel pump not kick on on a 92 Oldsmobile Cutlass


There is a red wire close to the battery in the front. It's not connected to anything. Apply positive voltage and that will run your pump for testing purposes.

Dec 08, 2015 | Oldsmobile Cars & Trucks

1 Answer

'93 cutlass ciera 3.3 wont stay on after starting up


ignition module getting warm and cutting of or auto shutoff relay loosing power..

Jan 05, 2014 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Coolant temp sensor


the coolant sensor in GM have the same color code for wire Black and yellow.Now coolant sensor is located on engine block or near thermostat.

Sep 16, 2013 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Would the mass air flow sensor make my 93 cutlass ciera c stall and then start later


that is possible pehaps you should check code jump aldl and read light for code dirty air filters can cause problems check harness connector also

Apr 30, 2012 | 1992 Oldsmobile Cutlass Ciera

1 Answer

I have a 1994 oldsmobile cutlass cierra and the waterpump is leaking and i need to know what tools i will need to change it out


wrenches and sockets the correct size and something to clean off the old gasket, the waterpump is probably the only easy thing to change on this car!

Jan 14, 2011 | 1994 Oldsmobile Cutlass Ciera

1 Answer

I have a 93 Olds Cutlass Ciera and the brake lights are out, and I can't find the fuse box. Can you help?


I have a 96 Olds Cutlass Ciera, and my fuse box is in my glove box. To the left, there's a black panel that says "Fuse Panel." Not sure if there's another one or not.

Sep 07, 2010 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Water pump?


if that waterpump pulley is wobbly loose , time to replace the waterpump. Hope this helps

Apr 09, 2009 | 1992 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...