Question about 2002 Jeep Grand Cherokee

1 Answer

My driver's side head light was knocked out of place in a fender bender. What part do I need to replace to fix it?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

You need depending on how bad it was nocked out of plce if it is broke then u will need the bracket, the headlight assembly.

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My turn signal and flasher fuses blow when I turn the ignition on


you have obvious short in the wiring - check the bulbs first, then the wiring. it is rarity to exchange relay - if it was not physically damaged during accident.

Apr 12, 2015 | Cars & Trucks

1 Answer

Air compressor wiring


Red and black should be power and black should be ground at the compressor clutch.

Jun 08, 2013 | Honda Accord Cars & Trucks

2 Answers

How do I replace the driver side fender on my 2012 dodge journey?


remove fender you have to raise vechicle remove wheel. remove splash shield remove bolts holding fender through wheel opening.then you have open hood remove headlight housing remove fender bolts behind head light housing.

Apr 03, 2013 | Cars & Trucks

1 Answer

Chrysler was in a fender bender. THe front left light and blinker was damaged need to be complete replaced. Cannot find anyone who carries the light for this model.


I would suspect any new parts were discontinued years ago.You will need to find a salvage yard but that will be tough because most of these places scrap the old stuff.Good luck and i will see if I can locate something for you.

Mar 06, 2011 | 1985 Chrysler Fifth Avenue

1 Answer

A minor fender bender knocked the pass side frt flare and fender splash guard off shearing all the fasteners. What do I need in order to re-fit them? Later, I will need to replace the front bumper cover -...


Any auto parts store will have those fasteners.Most just push in(one time use only)and others are two piece and can be used over and over.You will need to know the size of the hole where the fasteners lock into.

Jan 20, 2010 | 2003 Jeep Liberty

2 Answers

Car won't start


should be a fuel cut off switch on drivers floor on door side.

Nov 09, 2009 | 2002 Hyundai Accent

1 Answer

Fender bender, bought new assembly. How to remove old for replacement? "89 seville driver side headlight.


LIGHTING Headlights REMOVAL & INSTALLATION
  1. Unscrew the Torx retaining screws and remove the headlight bezel.
  2. Remove the headlight bulb retaining screws. These are the screws which hold the retaining ring for the bulb to the front of the car. Do not touch the two headlight aiming screws, at the top and the side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.
  3. Pull the bulb and ring forward, then separate them. Unplug the electrical connector from the rear of the bulb.
  4. Plug the new bulb into the electrical connector. Install the bulb into the retaining ring and then install the ring and the bulb. Install the headlight beze

Aug 23, 2009 | 1989 Cadillac Seville

1 Answer

Right Turn Signal not flashing.


quick fix,try to run jumper wire from solid lime green wire to tail light green/orange wire Your problem is no power

Apr 21, 2009 | Plymouth Acclaim Cars & Trucks

1 Answer

I need to change my passenger side headlight bulb on my 2002 beetle. Can anyone please send me a diagram on how to do this.


WHAT TO DO IS OPEN THE HOOD OF YOUR BEETLE AND WILL BEABLE TO SEE THE HEAD LIGHT. THERE IS A LEAVER THAT PUSHES DOWN TO EJECT THE HEAD LIGHT OUT OF THE FENDER. YES IT COMES ALL THE OUT OF THE CAR. YOU MAY NEED TO TAKE A SCREW DRIVER TO PUSH THE LOCK DEVICE DOWN TO PUSH LEAVER DOWN.ONCE YOU GET THE HEAD LIGHT OUT TAKE THE BACK OFF OF IT AND REPLACE THE BULBS. WHEN YOU PUT THE HEAD LIGHT BACK IN THERE ARE 3 GUIDES TO PUT THE HEAD BACK IN TO LOCK IT BACK IN PLACE. ONCE YOU HAVE IT IN THE GUIDES US THE LEAVER TO PULL THE HEAD LIGHT BACK INTO THE FENDER.

Mar 05, 2009 | 2002 Volkswagen Beetle Turbo S

1 Answer

Heat will only defrost, no matter where I put the dial.


In the front of the cherokee, right side under the bumper there is a football shaped plastic canister.
The canister is a resoiver for vacuum that control the heat and defrost doors. Either it is cracked from the fender bender or the body shop didn't connect the vacuum lines.

Dec 02, 2008 | 2001 Jeep Cherokee

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...