Question about GMC Envoy

Open Question

2006 Envoy service engine light on P0526 - Envoy GMC Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

keeperoffire
  • 106 Answers

SOURCE: Envoy 2006 gas & engine lights

The problem is that there are updates for the computer in your vehicle.The dealership can do what they call a flash and install those updates.The bad part in my opinion is that they dont inform the public of this and they will try to sell you a new computer when you dont need it.

Posted on Mar 03, 2009

  • 1 Answer

SOURCE: 2004 envoy service engine light stays on. Told

Our mechanic said we need to replace the computer! The cost will be $1,000.

Posted on Feb 27, 2010

  • 40 Answers

SOURCE: service engine light is on and code P0526

The Powertrain Control Module (PCM) uses the cooling fan speed signal in order to determine the actual fan speed in relation to the desired fan speed. The PCM uses the cooling fan speed signal in order to reduce the cooling fan noise and in order to maintain the powertrain cooling requirements. The PCM supplies power and ground to the clutch hall effect sensor of the cooling fan clutch. The hall effect sensor returns a signal pulse through the speed signal circuit in response to the reluctor track, which is located inside the fan clutch. If during operation, the PCM detects a loss of the cooling fan speed signal, DTC P0526 will set

  • An inline connector could cause an intermittent DTC. Ensure to test for poor connections and pin retention at all inline connectors. Refer to system schematics for connectors and locations.
  • If the condition is not present, refer to Testing for Intermittent and Poor Connections.
  • Disconnect the harness connector of the cooling fan clutch from the shroud. Inspect the exposed wires between the harness connector and the tubing.
  • Inspect the cooling fan clutch harness in order to ensure that the clutch supply voltage circuit is not shorted to the following circuits:
  • The 5-volt reference circuit.
  • The cooling fan speed signal circuit.
  • The low reference circuit.
  • DTC P0526 will set if the engine is started without the drive belt ON.

Posted on Mar 05, 2010

  • 1311 Answers

SOURCE: 2004 GMC Envoy with a P0526 sensor problem

This code indicates a problem with the fan clutch, the speed it is running is not the speed it was commanded to run/ The fan clutch assembly needs replacing.

Posted on Sep 09, 2010

ryanlutton
  • 1121 Answers

SOURCE: 2004 trailblazer, 2 wheel drive.

A couple of things come to mind. Double check the wiring at the fan clutch, check the whole harness, there is a known problem wth chaffing there. Is it a Dorman brand fan clutch? These have been known to be bad out of the box. The other thing that could be wrong is the actual speed sensor on the new fan clutch. Hope some of this helps.

Posted on May 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 envoy denali service air bag warning in dash?


Under the console, between the seats. Have the codes read first. These modules aren't cheap.

Nov 01, 2015 | 2006 GMC Envoy Denali

1 Answer

Service traction control light


The light has to be on when it is checked. Also it could be something as simple as tire pressure that is causing this.

Feb 15, 2013 | 2006 GMC Envoy

1 Answer

2006 envoy xl check engine light on. the service department said it was a bad battery. could that be the problem?


Could be, although I'm not aware of a specific code that exists that says bad battery. Envoys and Trailblazers need a lot of juice and if the battery is starting to go, look for more codes and problems to pull up with that check engine light. Did they give you a specific code? When the check engine light comes on, it's telling you that there is a code stored and will point to the problem. Code will almost always start with PXXXX

If you don't have a code reader yourself, take it to a place like Autozone that will check it for free and give you a printout of the code. Let me know if you need more help.

Jun 01, 2011 | 2006 GMC Envoy Xl

1 Answer

I replace the fan clutch and i still have the code p1481 what does that mean? 2002 chevrolet Trailblazer 4.2 Thanks You! Arthur Tyler


TSB#05-06-02-012B: Service Engine Soon (SES) or Check Engine Light On, DTC P0480, P0526/P1481/P1484 Set (Replace Engine Cooling Fan Wiring Harness) - (Oct 19, 2006)
Subject:
Service Engine Soon (SES) or Check Engine Light On,
DTC P0480/P0526/P1481/P1484 Set (Replace Engine Cooling Fan Wiring Harness)
Condition
Some customers may comment that the Service Engine Soon (SES) or Check Engine light is illuminated. This condition may be intermittent and upon investigation, the technician may find either DTC P0480, P0526, P1481 or P1484 set.

Cause
This condition may be caused by the cooling fan harness chaffing against the plastic guide it routes through. This
contact may damage the insulation of the wires enclosed in that harness.

Correction
Replace the engine cooling fan harness using the procedure listed below.

1. Remove the cooling fan. Refer to the Cooling Fan and Shroud Replacement procedure in the Engine Cooling sub-section of SI.

2. Place the cooling fan assembly on a bench.
Disconnect the harness electrical connector from the cooling fan clutch.

3. Remove the harness from the plastic guide while feeding the wires out of the slot.

4. Before installing the new harness, wrap the affected area on the wires with electrical tape to keep the protective sleeve in place. Be sure to keep the tape approximately 25 mm (1 in) away from the connector so the wires can be fed into the slot.

5. Feed the wires into the slot and install the harness to the plastic guide.

6. Connect the harness electrical connector to the cooling fan clutch.

7. Install the cooling fan. Refer to the Cooling Fan and Shroud Replacement procedure in the Engine Cooling sub-section of SI.

Part Number 89024920

Description
Harness Assembly, Engine Cooling Fan Wiring
Thank you for using fixya.

Apr 29, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

Service engine light is on and code P0526


The Powertrain Control Module (PCM) uses the cooling fan speed signal in order to determine the actual fan speed in relation to the desired fan speed. The PCM uses the cooling fan speed signal in order to reduce the cooling fan noise and in order to maintain the powertrain cooling requirements. The PCM supplies power and ground to the clutch hall effect sensor of the cooling fan clutch. The hall effect sensor returns a signal pulse through the speed signal circuit in response to the reluctor track, which is located inside the fan clutch. If during operation, the PCM detects a loss of the cooling fan speed signal, DTC P0526 will set
  • An inline connector could cause an intermittent DTC. Ensure to test for poor connections and pin retention at all inline connectors. Refer to system schematics for connectors and locations.
  • If the condition is not present, refer to Testing for Intermittent and Poor Connections.
  • Disconnect the harness connector of the cooling fan clutch from the shroud. Inspect the exposed wires between the harness connector and the tubing.
  • Inspect the cooling fan clutch harness in order to ensure that the clutch supply voltage circuit is not shorted to the following circuits:
  • The 5-volt reference circuit.
  • The cooling fan speed signal circuit.
  • The low reference circuit.
  • DTC P0526 will set if the engine is started without the drive belt ON.

Mar 05, 2010 | 2004 GMC Envoy

1 Answer

2006 Envoy Denali: nunmber 6 cylinder is not firing


yes repace plug wire and recheck still has mis replace coil pack.I hope this helps you?

Oct 03, 2009 | 2006 GMC Envoy Denali

2 Answers

I have a service engine soon light and the code that appeared when check is 1481, do you know what this means?


Service Engine Soon (SES) or Check Engine Light On, DTC P0480, P0526/P1481/P1484 Set (Replace Engine Cooling Fan Wiring Harness) #05-06-02-012B - (10/19/2006)

Models:2004-2006 Buick Rainier
2002-2006 Chevrolet TrailBlazer, TrailBlazer EXT
2002-2006 GMC Envoy, Envoy XL, 

Some customers may comment that the Service Engine Soon (SES) or Check Engine light is illuminated. This condition may be intermittent and upon investigation, the technician may find either DTC P0480, P0526, P1481 or P1484 set.

This condition may be caused by the cooling fan harness chaffing against the plastic guide it routes through. This contact may damage the insulation of the wires enclosed in that harness.

Replace the wire harness: 
Part Number 89024920 Description Harness Assembly, Engine Cooling Fan Wiring

Good luck and keep me posed. 

Aug 11, 2009 | 2003 GMC Envoy

1 Answer

2004 GMC Envoy with a P0526 sensor problem


This code indicates a problem with the fan clutch, the speed it is running is not the speed it was commanded to run/ The fan clutch assembly needs replacing.

Jun 03, 2009 | 2004 GMC Envoy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...