Question about 2003 Ford F250 Super Duty Crew Cab

Open Question

I replaced the fuel pump on my 2003 Ford F250 6.0L diesel truck and forgot to write the color codes down for the wiring. Now I don't know what wire goes where. Can you help?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
raycrazek
  • 106 Answers

SOURCE: Fuel Pump wire color code?

you know they have those books at the local autozone that have all that info in them. they sell for about 10 or 15 bucks good-luck ray

Posted on Jan 16, 2009

Ad
Just_Bobz
  • 448 Answers

SOURCE: radio wire color codes for a 99 ford explorer sport

With 20 years audio experience under my belt, no you don't. Premium chat me and I can tell you how to find every wire

Posted on Jan 17, 2009

motor1258
  • 6674 Answers

SOURCE: Fuel pumps will not run!

Hey lets try this ! Locate your starter solenoid & look for a yellow wire marked with a "W" . That may be the fusible link for fuel pump. Let me know what you find.

Posted on Apr 14, 2009

DIESELMUDDER
  • 2760 Answers

SOURCE: replace fuel pump on 03 Ford F350 diesel

simple : obtain replacement pump from parts provider (no used stuff)

Now help me out here: thats the year they were bolted to the pass side front of engine
and not inside the tank right? (better go look to see for sure)

using a tube wrench unscrew the fuel lines (i use large wire nuts to temp block off fuel leakage)

with a 12 mm wrench undo the two side bolts holding the pump to block

wiggle pump it should come straight off

clean mounting place on block with solvent let dry

silicone back (or use gasket that comes with pump ) of pump

apply pump to block (depending on where crank stopped you may have some tension on arm you will have to overcome to get flange to meet block )

use locktite (blue)or simmiliar thread lock on bolts retighten firmly but not hang up the dog tight

use light grease or vasolene on tube connections don't try to tighten dry

Now the fun part your diesel now has air in the fuel system

there are two ways to remove this ( hard and harder)
your choice here are both methods

loosten the fuel supply line for #8 injector ( I did not say remove) 1 full turn ought to be enough

crank engine 30 seconds only
wait 5 minutes for starter to cool down
crank engine 30 sec again
did it start but runs rough while it's still running tighten #8 injector (caution fuel under high pressure)
engine smooth out good your lucky
engine did not start yet
wait 5 minutes
crank engine 30 sec again
start yet
if so tighten #8 injector up

Now here's something I've done to my diesel to make this much less a hasstle

trace fuel line as it comes up from pump
obtain a small low pressure electric fuel pump and a two short pieces of fuel line
and a few clamps

use tube cutter and cut fuel line just before it bends to go in filter
deburr edges
slide tube and clamps over pipe (both sides)
insert pump observe flow arrrow towards filter

the wires of pump can be stretched over to #1 battery terminals

now any time you change a filter or open your fuel system for any reason
all you need do is connect pump to battery
open sharader valve on top of filter for a few min
and start truck as normal
then disconnect wires and stow away for another day

Posted on Jul 08, 2009

  • 1 Answer

SOURCE: ford f250 diesel no accelration or instrument panel

blown 10amp fuse in cab

Posted on Jul 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repair 2008 ford F-350 diesel showing code P2033


code p2033 refers to exhaust gas temperature (EGT) sensor 2 bank 1 circuit high === causes wiring short to ground --EGT sensor . check the wiring for shorted / broken wires and replace the sensor . If there is no problem with the sensor or the new sensor fails early I would be checking the fuel settings on the pump ( pump timing and cc ratings ) as a hot diesel exhaust indicates over fuelling or pump timing too far advanced.

Jul 22, 2014 | 2008 Ford F-350 Super Duty

1 Answer

I have a 2003 crown victoria cvpi the fuel gage is not working, i belive that if i knew the color of the positive wire going to /from gas tank i could rewire or repair the fuel gauge problem the car was...


These should be the colors coming out of the plug on the fuel pump.

(GY/RD)signal return
(RD/PK)Fuel tank pressure transducer sensor
(BN/WH)Reference voltage
(YE/WH)Fuel pump/fuel gauge sender
(BN/WH)Fuel pump Power, return
(PK/BK)Fuel pump Power, feed
(PK/OG)Ground

I hope this helps you out.

Mar 14, 2011 | 2003 Ford Crown Victoria

2 Answers

Won't start but cranks has 300k miles. Check fuel pump working, replace glow plugs, checked fuses and relays, fuel pump won't come on but works hooked it direct to battery, wait to start light does not...


If you can't pull the codes from the pcm it has either died or lost it's ground assuming it has power. I would try to get a wiring diagram and check both the power and the ground for the computer itself, because it is what turns on the pump and the wait to start light.

Feb 25, 2011 | 1999 Ford F350 Regular Cab

1 Answer

I need to know how many wires go to a 1989 ford econoline fuel pump with a 460 efi engine


I suggest check this wiring diagrams for code color wires...


1989 5.0L & 5.8L & 7.5L ENGINE SCHEMATICS

2fa9322.gif




1989-91 CHASSIS (GASOLINE)SCHEMATICS

6dd87e2.gif



1989-91 CHASSIS (DIESEL) SCHEMATICS

1887a7c.jpg


Hope this help.

Mar 23, 2010 | 1989 Ford Econoline

3 Answers

I am looking for a wiring diagram for a F-150 alternator. Do you have one I can download? late 80's and up...


fuel pump an fuel gauge shuts down when i move the wires under the hood can not locate wire color code

Dec 31, 2009 | 1988 Ford F 150

1 Answer

Is their a fuel pump in tank of E350 7.3 diesel 1988 ford ?


my guess is there is a fuel pump in tank as there are in 95% of diesel motor vehicles. you may have just sucked out the existing fuel from the lines. the fuel pump can withstand high amounts of amperage and voltage so by hooking up wires wrong i dont think you burned up the pump but you may have wired it up wrongly, or you have forgot to put the o rings back inthe housing properly. or drop on in tank. check the fel system setup. Orings in place, wiring connected properly. if all else fails give the pump a hit and see if it will start.

Aug 09, 2009 | Ford E-350 Cars & Trucks

1 Answer

Replace fuel pump on 03 Ford F350 diesel


simple : obtain replacement pump from parts provider (no used stuff)

Now help me out here: thats the year they were bolted to the pass side front of engine
and not inside the tank right? (better go look to see for sure)

using a tube wrench unscrew the fuel lines (i use large wire nuts to temp block off fuel leakage)

with a 12 mm wrench undo the two side bolts holding the pump to block

wiggle pump it should come straight off

clean mounting place on block with solvent let dry

silicone back (or use gasket that comes with pump ) of pump

apply pump to block (depending on where crank stopped you may have some tension on arm you will have to overcome to get flange to meet block )

use locktite (blue)or simmiliar thread lock on bolts retighten firmly but not hang up the dog tight

use light grease or vasolene on tube connections don't try to tighten dry

Now the fun part your diesel now has air in the fuel system

there are two ways to remove this ( hard and harder)
your choice here are both methods

loosten the fuel supply line for #8 injector ( I did not say remove) 1 full turn ought to be enough

crank engine 30 seconds only
wait 5 minutes for starter to cool down
crank engine 30 sec again
did it start but runs rough while it's still running tighten #8 injector (caution fuel under high pressure)
engine smooth out good your lucky
engine did not start yet
wait 5 minutes
crank engine 30 sec again
start yet
if so tighten #8 injector up

Now here's something I've done to my diesel to make this much less a hasstle

trace fuel line as it comes up from pump
obtain a small low pressure electric fuel pump and a two short pieces of fuel line
and a few clamps

use tube cutter and cut fuel line just before it bends to go in filter
deburr edges
slide tube and clamps over pipe (both sides)
insert pump observe flow arrrow towards filter

the wires of pump can be stretched over to #1 battery terminals

now any time you change a filter or open your fuel system for any reason
all you need do is connect pump to battery
open sharader valve on top of filter for a few min
and start truck as normal
then disconnect wires and stow away for another day

Jun 29, 2009 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

Fuel Pump wire color code?


you know they have those books at the local autozone that have all that info in them. they sell for about 10 or 15 bucks good-luck ray

Jan 16, 2009 | 1991 Ford F150

Not finding what you are looking for?
2003 Ford F250 Super Duty Crew Cab Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...