Question about 1999 Pontiac Bonneville

1 Answer

Security system disarm it - 1999 Pontiac Bonneville

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Pontiac Master
  • 75,117 Answers

The system is disarmed every time you lock and unlock the doors with the key or remote, there is no other disarm, so if that is not happening the system has a fault and will need to be scanned for the problem part

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My security Light is on and it won't even turn over


You need to disarm the security system. It won't start because the system has an immobilizer that will prevent your car from running until the alarm is disarmed.

Feb 08, 2016 | Cars & Trucks

1 Answer

How to disarm security system 2005 cts


Hello. Security systems (alarms) can cause problems when they become bad. The best thing to do is disconnect the fuse for the alarm. Look in the fuse panel of your car and see which one is for the security system (alarm). Then you can pull out the fuse and it will disarm the security system. Good Luck.

May 28, 2014 | 1998 Jeep Grand Cherokee

1 Answer

Replaced battery in my 1993 jeep grandcherokee limited now security system seems to cut fuel off seconds after engin fires


Here's some info as it sound like the theft deterrent is armed.

---
Reset Procedure

NOTE: This information applies to a Vehicle Theft Security System (VTSS) that was armed when the battery was disconnected and reconnected.

When the armed VTSS senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode the alarm system remains armed following a battery failure or disconnect. If the VTSS was armed prior to a battery disconnect or failure, the system will have to be actively or passively disarmed following a battery reconnection.

The power-up mode will also apply if the battery goes dead while the system is armed and battery jump-starting is attempted. The engine no-run feature will prevent the engine from starting until the alarm system has been actively or passively disarmed.

Passive disarming of the Vehicle Theft Security System (VTSS) occurs when the vehicle is unlocked using the key to unlock either front door or the liftgate. Active disarming of the VTSS occurs when the vehicle is unlocked by depressing the Unlock button of the Remote Keyless Entry (RKE) transmitter.

Once the alarm has been activated (horn sounding, lights flashing, and the engine no-run feature), either disarming method will deactivate the alarm.

Depressing the Panic button (if equipped) on the RKE transmitter will also disarm the VTSS, but the horn will sound and the lights will flash for about three minutes as part of the Panic feature. The horn and lights can be stopped by pressing any of the RKE transmitter's buttons or driving the vehicle above 15 mph.

Feb 11, 2013 | Dodge Stratus Cars & Trucks

1 Answer

HOW TO DISARM SECURITY SYSTEM


The system is automatic and disarms as soon as the key is used or the remote. If it is locking you hurt then it has a fault in the system and you need to have the security system scanned by the GM dealer to see what is locking you out.

Jul 04, 2012 | Cars & Trucks

1 Answer

How to disarm security system in 1998 olds sillouhette


This is very possible, and it can be done yourself. Go to this link. Read thru it in entirety so you understand how the system works. There are some links on there that will help you out.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Mar 16, 2012 | 1998 Oldsmobile Silhouette

1 Answer

SECURITY SYSTEM KEEPS SHUTTING THE CAR OFF. RESETTING THE SYSTEM DOESN'T HELP. HOW DO I BYPASS THE SECURITY SYSTEM


If you are handy with vehicle electrical, you can apply ground to the factory disarm wire, to permanently disarm the factory security. It's location and color;

Factory Disarm Purple/Yellow (-) in Driver's Kick Panel---Black Connector

Feb 14, 2011 | 1995 Jeep Grand Cherokee

1 Answer

How do I disarm my security system without the original key


You can ground the factory disarm wire, to permanently disarm the factory security. That wire's location and color is as follows;
Factory Disarm-----Purple/Yellow (-)----- Driver's Kick Panel Black Connector

Feb 07, 2011 | 1993 Jeep Grand Cherokee

1 Answer

How do i change a blower motor in a ford tempo 1992? i have the blower motor lose but the bottom og the glove box bar is in my way. how do i take that out to get the motor out?


Less Air Conditioning

  1. On models equipped with airbag, disarm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. Disconnect battery ground cable.
  3. Remove screws securing right ventilator control cable to instrument panel.
  4. Remove screw securing right register duct to lower right edge of instrument panel.
  5. Remove glove box and hinge bar from instrument panel.
  6. Pull right register duct from installed position between air inlet duct and right register opening, Fig. 10.
  7. Remove ventilator grille from bottom of ventilator assembly, then screws securing right ventilator assembly to blower housing.
  8. Remove hub clamp spring from blower wheel hub, Fig. 11.
  9. Pull blower wheel from blower shaft, then remove three blower motor flange attaching screws.
  10. Pull blower motor from housing, disconnect electrical connector, then remove motor from vehicle.
  11. Reverse procedure to install.
  12. On models equipped with airbag, rearm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
With Air Conditioning

  1. On models equipped with airbag, disarm airbag system as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. Disconnect battery ground cable.
  3. Remove glove box door and instrument panel lower reinforcement from instrument panel.
  4. Disconnect blower motor electrical connector, then remove blower motor and mounting plate from evaporator housing.
  5. Rotate motor until mounting plate flats clear edge of glove box opening, then remove motor.
  6. Remove hub clamp wheel spring from blower wheel hub and remove blower wheel from motor shaft.
  7. Reverse procedure to install.
  8. On models equipped with airbag, rearm airbag system as described underMAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.

Dec 18, 2010 | 1992 Ford Tempo

1 Answer

NEED TO DISARM SECURITY SYSTEM WENT BAD


Try turning the key in the rear hatch key cylinder. That should disarm the factory security system.

Nov 19, 2010 | 1995 Jeep Grand Cherokee

1 Answer

I have a viper alarm on my car that wont shut off nor i cant start the car..and i have tried the button under my dash, how Can i shut it off??


was it a professional or shade tree install? the following is off vipers website:
disarming without a remote control
This feature allows you to disarm the security system without the
Remote Control should it be lost, damaged, or disabled. In order to
disarm the system without a remote remote control, you must have
the vehicle’s ignition key and know where the Valet button is
located. Be sure to check with the installer for the location and the
number of presses of the Valet button required to disarm the system.
To disarm the security system,
turn the ignition to the ON position.
Press the Valet button the
preset number of times (one to
five times) within 15 seconds. After five seconds the system will
disarm. If the system does not disarm, you may have waited too long;
turn the ignition off and on and try again.
if that doesn't work try this other

valet mode
You can prevent your security system from automatically arming
and triggering by using Valet Mode. This is very useful when
washing the vehicle or having it serviced. In Valet Mode, the
security system will not arm, even with the Remote Control, but
all convenience functions (door locks, trunk release, etc.) will
continue to work normally.
To enter or exit Valet Mode:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
button within 10 seconds.
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.

May 08, 2010 | 1994 Honda Civic

Not finding what you are looking for?
1999 Pontiac Bonneville Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...