Question about Jeep Liberty

3 Answers

Replaced crank sensor and now Im getting PO725 code.Would it be the camsensor that is giving me this code?

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 8,266 Answers

No, that code is for crank sensor:

Engine RPM input - circuit malfunction

Possible Causes: Wiring, CKP/RPM sensor, ECM/TCM

Posted on Oct 01, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 14,036 Answers

CODE PO725 A/T ENGINE SPEED SENSOR CIRCUIT MALFUNCTION.YOU NEED CODE ERASED AFTER REPLACING THE CRANKSHAFT SENSOR.IF CODE PO725 STILL REMAINING.YOU HAVE WIRE FAULT ELECTRICAL CONNECTOR OR FAUTY PCM.

Posted on Oct 02, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Expert
  • 1,868 Answers

Hello! No, it's the Vehicle Speed Sensor (VSS)...Send the year, model, and engine size and I'll be more specific...Guru..Saailer

Posted on Oct 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do you have to take apart to get to the cam position sensor


Take the front timing cover out the camsensor and crank are one harness,steps are take cover off remove camsensor,remove cranksensor ,you dont need to remove timing belt.

Apr 02, 2012 | 2002 Mitsubishi Montero Sport

1 Answer

Po725 code on chrysler sebring can it cause the starter to go bad


Hi there:

DTC P0725 - ENGINE SPEED SENSOR CIRCUIT


When Monitored: Continuously after a ignition key is turned from the OFF to RUN

position and/or key is turned from the CRANK to the RUN position.

Set Condition: The code is set when the engine speed sensed by the Transmission Control

Module (TCM) is different than the engine speed reported by the Powertrain Control

Module (PCM) over the Communication Buss.


POSSIBLE CAUSES:

CHECKING SYMPTOMS AND POSSIBLE CAUSES

LOW BATTERY VOLTAGE

BAD CONNECTIONS AT VARIOUS CONNECTORS

CRANK POSITION SENSOR SIGNAL OPEN

CRANKSHAFT POSITION SENSOR GROUND CIRCUIT OPEN

TCM CRANK POSITION SENSOR MONITORING DEFECTIVE



Hope this helps.

Mar 30, 2012 | 2001 Chrysler Sebring

2 Answers

I have a 98 chevy z71 5.7 350 vortec, i have a p1345 code that stays on i clear it and as i restart the truck it comes back on, the truck runs great and has a small delay when starrted.. what can/do i need...


1345 is cam and crank sensor correlation its mainly the cam sensor going out, also the delay start that also trigger a camsensor code they call it excessive crank time check the fuel pressure that is capable of setting a cam code (1345) If fuel pressure is good (55-60 psi) expect to replace the camsensor you might as well do the crank sensor heres a nightmare on this code it can set if the distributor is off one tooth and yes these distributor have high failure rate

Jun 08, 2011 | 1998 Chevrolet K1500

1 Answer

I need to locate the vehicle speed sensor on 2006 4 cylinder Nissan ALtima


if its a po725 code its engine speed fault ,replace crank sensor.for vehicle speed there are two identical sensors near each other on trans....one called revolution sensor other is called turbine speed sensor.

Feb 05, 2011 | 2006 Nissan Altima

1 Answer

Nissan 2.5 repair code po335-po725 car shot off while runing


FIRST THE P0335 CODE IS A CODE FOR LOSS OF CRANK SENSOR SIGNAL... MOST OF THE TIME YOU NEE TO REPLACE THE CRANK SENSOR... NEXT THE CODE P0775 IS FOR A PRESSURE SENSOR CODE FOR TRANNY... ERASE THAT CODE AND JUST SEE IF IT RETURNS...NOT A BIG DEAL ON THAT ONE

Sep 01, 2009 | 2003 Nissan Altima

1 Answer

PO725 Engine speed sensor circuit malfunction


Trouble Code: P0725


A/T Engine Speed Sensor Circuit Malfunction

Possible Causes:


Check for trouble codes related to the CKP Sensor

CKP Sensor signal circuit open, shorted to ground or to power

CKP Sensor is damaged or has failed (open or shorted)

Intermittent wiring or connector problems

PCM has failed

May 24, 2009 | 2002 Jeep Grand Cherokee

1 Answer

S10 pickup misifirng when light highway load


I had to rebuild my engine at 97000 miles cuz of low engine oil pressure and bad berrings

Dec 14, 2008 | 2000 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

867 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...