Question about 1992 Honda Accord

1 Answer

Changing altenator belt

How hard is it to do?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 198 Answers

It depends on your skills

Posted on May 26, 2008

  • kishore swamy May 30, 2008

    may i kno y u ve rated tis as inappropriate

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 Nissan won't start after changing altenator belt


If you changed the belt, that means that you have been having problems with your altenator. You battery is probably dead.

Dec 03, 2013 | 1998 Nissan Maxima

1 Answer

2002 chevrolet pick up v6 excessive noise from belts replaced idler and tensioner ,no help power steering works fine ,altenator charging, a/c ok water pump ok rotated altenator, by hand when changing...


I would suspect the altenator, A/C pulley, or the belt. when you checked the altenator and a/c they have to turn smoothly with no play or roughness. If these checked out fine then I would check the belt, they do stretch.

Nov 28, 2010 | 2002 Chevrolet Silverado 1500

1 Answer

How do i disconnect alternator in 1996 lincoln towncar. key wont work


disconnect the positive cable from battery 1st then on back of altenator there will be a plug in with a plastic lock tab holding it in. with a straight screw driver pry back gently on the locking tab and pull the plug out. then there will be a nut to remove also. you may have to slide the rubber cover thats over it to see it. once exposed,you'll see it,most likely a 10 mm nut. remove it and the altenator is unplugged. removal of altenator from engine isn't that hard either. with a ratchet insert the ratchet into the belt tensioner and rotate it counter clockwise and the belt will loosen,slide belt off of the altenator, then remove the two bolts that hold it in place. installation is the reverse of removal. if you need further assistance please ask and we'll be glad to help you!!thank you for choosing fixya.com!!

Nov 21, 2010 | 1996 Lincoln Town Car

1 Answer

How to change altenator rib belt


there should be an idler pulley that also adjust the tension the tool usually used is a 3\8 or 1\2 ratchet

Jun 05, 2010 | 2000 Lexus ES 300

1 Answer

Change alternator


It's easy...
Disconnect the battery
Remove the supentine belt from the altenator pully, you can use a 3/8" drive breaker bar on the belt tensioner, just insert into the square slot on the tensioner and rotate it clockwise.
Remove the power wire and the harness
Remove the mounting bolts 1 under and 2 on the sides.

Just reverse the process to install the new altenator.
Make sure the supentine belt is in the proper position.
Make sure the battery is charged before starting, a drained battery can damage the FETs on the new altenator.

May 22, 2010 | 2004 Ford Mustang

1 Answer

Battery light came on,and stirring became hard toturn.sterring


battery light will come on if there is a prob with your altenator or your battery...

firstly check if you still have a fanbelt, it may have come off and this will cause both of these problems and eventualy cause your car to overheat aswell

if there is a problem with the altenator seizing etc it may effect your power steering pump causeing steering to be hard to turn, observe if there is anything abnormal about the drive belt opperation (noise, vibration, spinning slowly, or appears buckled etc...) if so then you will need to remove the belt and check all the pulleys (prob start with the altenator)

Feb 10, 2010 | 2000 Ford Focus

1 Answer

Change moter alt belt keeps breaking


Hi the altenator belt? if it keeps snapping then your altenator is rather starting to seize up or its not fitted correctly, normally if its squeking its to loose.

Spin the altenator by hand and see what it sounds like, if its hard to turn or noisey that the fault.

hope this helps.

Jan 16, 2010 | 2000 Kia Sephia

1 Answer

Change belts


the other one is the power steering belt and they are fairly easy to change.

Nov 28, 2008 | 2001 Toyota Avalon

1 Answer

Problem with Altenator belts Etude


the problem is not the altenator. you should have a idler pully and a self adjusting idler tensioner. if thes e go bad the bearings tend to seize up and break belts i would check these first chance you get the tensioner should be spring like and be hard to move back and forth the pulley part of it should spin freely with out makeing a noise. please rate this

Sep 01, 2008 | 1999 Mazda 626

1 Answer

1994 geo metro


It's actually super easy.
All you need is your year and make alternator belt and a wrench.
Take off the existing altenator, take off the old belt.
Once the altenator is off you'll be able to look further down below where the altenator was. You'll see a metal wheel that's a little bigger than the one on the altenator. This is where the new belt needs to wrap around.
I found it alot easier to wrap the belts around the two wheels before putting the altenator back on the engine.
Make sure that all bolts and seals are sound. (that's the last thing you need falling off in the middle of nowhere!)
Hope it helped!

Aug 29, 2008 | 1994 Geo Metro

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...