Question about 2000 Jeep Grand Cherokee

1 Answer

2000 Jeep Grand Cherokee, I had blinkers and flashers no brake lights, and after checking the bulbs in the light itself I dont have blinkers or flashers at all

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Just no turn signals in the back now? Maybe didn't install the bulbs tight back into the asm? No brake lights...do the lights work with headlights on and just no illumination with the brake pedal depressed? Could be brake light switch.

Posted on Oct 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep grand cherokee none of the rear lights work


Check BackUp Module, generally is located in the rear quarter panel (drivers side).

Dec 23, 2012 | 2000 Jeep Grand Cherokee

2 Answers

I have a problem with a 93 Jeep Cherokee Laredo 4W - The right blinker & brake light works like they should. However,the left brake & backup lights are out ( new bulbs have been installed &...


a very bad earth in that lamp holder,, clean all the earths and try another new buld in it, iv had this before and that was the problem sorted

Nov 02, 2009 | 2000 Jeep Wrangler

1 Answer

2000 Grand Cherokee both brake lights off. Hatch brake light works. All other flashers, lights and turn signals work. What now?


You may just have 2 bulbs out. Remove the socket from the housing and check it with a test light, while having a friend step on the brake. If you have no power at either side, check all related fuses and make sure your trailer harness connector doesn't look like a green fuzzball.

Jun 29, 2009 | 2000 Jeep Grand Cherokee

4 Answers

I have a 1999 Jeep Grand Cherokee Laredo - One Brake Light


First, I want to say thank you for the info, you saved me money and aggravation. Second it took mea little while to figure out what contact I was looking for. So I would like to provide a little more detail to make it easier for others in the future.
This is the corrective method for your brake lights not working when your headlights are on(2000 Jeep Cherokee Larado).
1) The cause of the problem is heat from the bulb.
2) Remove the light assembly as if you were going to change a bulb.
3) Turn the socket and remove it from the taillight assembly and set it aside(check to be sure your bulb is not burnt out).
4) Look at the opening, you will see 3 flat chrome colored contacts on the assembly.
5) Notice the one by it self at the top of the opening, that is the "ground".
6) If you look closely you will notice the plastic around the ground contact has shrunk a little bit, this caused the contact to pull away from the socket, causing the problem.
7) With a small flat head screwdriver, VERY GENTLY pry up the contact so it stays slightly upward by itself.
8) Re-insert the bulb assembly back into the housing and press your brake petal with your lights on.
9) You should be in good to go!
10) Tools: Phillips head screwdriver and a small flat head screwdriver.
11) Time : 5 minutes per light

Jun 08, 2009 | 2001 Jeep Grand Cherokee

2 Answers

Indicator stays on


i am going to take it you are talking about the turn signal...look for a burned out bulb...that will cause this condition

Oct 30, 2008 | 2000 Jeep Grand Cherokee

3 Answers

Blinkers not working


Did you check the bulbs? If one bulb is burned out, the blinkers won't word on that side. You could have one bulb burned out on each side. Start the car, put left signal on. Check front and back lights. Is one light on but not blinking? If that's the case, the light that's not on at all is burned out and has broken the circuit so the good light stays on and won't blink. Check the other side. You also have a 'flasher' , actually 2. One for emergency flashers, one for the turn signals. It could be that the turn signal flasher is shot. You just have to unplug it to remove. It's probably located near the fuses. good luck countrycurt0

Aug 10, 2008 | 1999 Jeep Grand Cherokee

1 Answer

Brake lights quit working. All fuses and bulbs are good. There is a blue wire labeled "electric brake" hanging by the pedal switch. where is this supposed to go?


I have had this problem for over 8 months. Break light would work, blinker would not . . . then blinker would work, break light would not . . . turn headlights left break light would go out . . . FINALLY my 75 year old father figured it out !!!! It was the STOP SWITCH - even though it showed it was working - Please replace it anyway !!! It's only $14.00 for the part. Also the other part needing replaced was the Flasher Relay - $34.00 !! NOONE not even JEEP could figure out this problem !!!

Jul 20, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...