Question about 2001 Suzuki Esteem

Open Question

What are the torque specifications and bolt pattern for a 2001 suzuki,esteem 1.8 liter 4cylinder sedan?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 743 Answers

SOURCE: oil and transmission pan bolt torque specs

124 inch lbs on oil pan...Transmission pan 13 ft lbs.

Posted on Oct 12, 2009

  • 3 Answers

SOURCE: How do I remove the

I have a suzuki esteem 2000 and to remove the inside of the door panel you must first locate the window roll down lever and when you push back on the panel it opeans up a gap between the lever and the panel and if you look there is an axile that connects to the lever and in the lever there is a set of groovs and if you look at the groves there is a snap on ring, you must first push that ring off of the axile which will let you to freelly pull the lever off and then you can locate the screws that also hold the panel on my suzuki I have one on the handle which is covered by a plastic cap and there is also another palstic cap a little lower. After you have freed the screws the rest are just snap on clips you can just pull the panel off.

well hope it was helpfull.

Posted on Sep 12, 2008

  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

martin538
  • 117 Answers

SOURCE: need head bolt torque settings for 200 landrover discovery 4.0 liter 241 cu.in.

Stage 1 20nm
Stage 2 +90 degrees
Stage 3 +90 degrees

Posted on Apr 13, 2009

  • 1 Answer

SOURCE: how do i changing alternator suzuki esteem 2001

take it to a mechanic trust me, i had to replace mine after 6 days of trying to figure out how to remove the bottom bolt i took it to a shop if you need to know more email me KRAGAR33@AOL.COM

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 f150 5.4 4x4 front wheel bearing torque specs


If you have it apart, you should know already. If not, and you're doing this right, it should have four bolts, correct? I wouldn't worry about torquing them to anything specific, I'd tighten them snugly, then maybe 1/8 to 1/4 turn more in a criss-cross pattern. should be fine, they're not head bolts or lug nuts, so torque specs aren't necessary, but if you REALLY need the torque spec, I'd suggest going into an f-150 forum, sounds like a logical thing to do.

Mar 21, 2017 | Ford F-150 Cars & Trucks

2 Answers

Can't find the torque head bolt pattern for a 1996 gmc sierra 5.7 vortex


The "pattern" for ANY cylinder head is pretty much the same...start with the bolts in the center of the head and work your way out to both ends.
Torquing the cylinder head on your 5.7L Vortec engine to manufacturer specifications requires the use of a "torque angle" gauge, as well as a traditional torque meter.

The torque specifications are as follows:

> Step 1: All bolts: 22 Ft Lbs (30 Nm.)
> Step 2: Short bolts: Additional 55 degrees; Medium bolts: Additional 65 degrees; Long bolts: Additional 75 degrees

May 20, 2012 | GMC Sierra 1500 Cars & Trucks

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

What are the torque specifications for the intake manifold on a 2003 Ford F150 4.2 liter engine?


These torque specs are from the Haynes manual (Ford pick-ups 97' - 03') This is a 2- step proccess. step-1 44-in-lbs step-2 89-in-lbs. There are 14 bolts that hold the manifold in place, tightening sequence goes as follows: start from the center( WORK IN A "X" PATTERN)

Oct 02, 2010 | 2003 Ford F150 Regular Cab

1 Answer

I removed thehead need to know how much lbs to torque them at


Check your local library to see if they have a repair manual for this vehicle. You need to torque the bolts in a specific sequence (pattern), as well as to the correct torque. If they don't have it, you need to buy or borrow one. If you tighten them incorrectly, you can damage the engine.
While the manual may not say this, I always tighten all of them in the sequence given, first to about one-third of the torque limit, then come back and tighten all to about two-thirds, then to the full torque.

Aug 24, 2010 | 2001 Suzuki Esteem

1 Answer

I have 2001 chevy cavilier with the 2.2 liter motor I had to replace the camshaft and the lifters and need to know the torque ratio for the bolts on the head


the long bolts (along the backside/intake side of engine) should be torqued to 63Nm (46ft/lb)
the shorter ones (4 bolts along the front/exhaust side and the stud at the end that's attached to the trans) need to be torqued to 58Nm (43ft/lb) with the pattern of:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

Nov 21, 2009 | 2001 Chevrolet Cavalier

1 Answer

How do i changing alternator suzuki esteem 2001


take it to a mechanic trust me, i had to replace mine after 6 days of trying to figure out how to remove the bottom bolt i took it to a shop if you need to know more email me KRAGAR33@AOL.COM

Oct 11, 2009 | 2001 Suzuki Esteem

1 Answer

Need torque specs for 1.3 liter motor,connecting rod bearing and main bearings.


MAIN BEARING TORQUE IS 36 -41 FT LBS. ROD BEARING TORQUE IS 24 -26 FT LBS

Jul 07, 2009 | 1995 Suzuki Esteem

Not finding what you are looking for?
2001 Suzuki Esteem Logo

Related Topics:

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...