Question about 2003 Chevrolet Impala

1 Answer

Were do i find the crank shaft senser because my car want crank

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

If your car won't crank over by using the starter, I would not be looking there. I would be thinking battery, starter, or mechanical freeze up if the crankshaft will not spin.

Posted on Oct 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

6ya.com

Download 6ya

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93 Ranger 4.0 cranks but no start, no spark, replaced coil pack, crank shaft senser, cam shaft sensor, icu, ecm, hot to coil pack,fuel pressure good
Check the fuel pump emergency cut off just in case also may want to look at the ECM..

Apr 27, 2017 | Cars & Trucks

1 Answer

Where is the crank senser
Most are to the side of front crank shaft.

Sep 03, 2012 | 1999 Oldsmobile Intrigue

1 Answer

WI'll the crank shaft senser cause it to miss?
Yes it will. It is an important sensor that has to do with your vehicles timing. Below is a description of what it does. Hope this helps.....

4_1_2012_1_24_33_pm.jpg

Apr 01, 2012 | 1996 Ford Ranger SuperCab

1 Answer

1999 silverado 4.3 will run for few seconds then stall
You must hook up a live data scan tool (available on ebay for about $100.00) to see what is going on with the signals coming from those sensors. You may also have a defective Powertrain control module (PCM) or a wiring harness problem, I would lean towards the engine part of the EEC wiring harness as PCM problems are very rare.

Mar 18, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

Picture of engine of 1992 buick 3.8 crank shaft posistion senser
you have to remove the harmonic balancer on the crank shaft to remove the sensor.
you will need a harmonic balancer puller.

Oct 07, 2011 | 1992 Buick LeSabre

1 Answer

Where is the crank senser?
its at the damper pulley thats the big one at the end ov crank shaft not very big held on by 2 bolts

Apr 04, 2011 | 2002 Pontiac Grand Am

1 Answer

Where is crank censer located on a 1997 s10 truck?
the jeep wraangler is on the bell housing on the drivers side and can be addressed from under the drivers side behingd the front wheel. The S10 the cranks senser depends on the motor size and the year but if it's a 87 4.3 it's in the bottom of the timing cover just behinf the cranks shaft pulley for the belt drive.

Dec 12, 2010 | 1987 Jeep Wrangler

1 Answer

1994 buick lasaber wont start no spark why and what is it
if this is the 3.8 they have a problem with the cam shaft magnet falling off the timing gear if you pull the senser and turn the motor over by hand you can feel if the magnet is still there the senser is on the front of the motor above the water pump it also has a crank shaft senser behind the balencer

Oct 15, 2010 | 1994 Buick LeSabre

1 Answer

Car is getting gas and getting spark but won't start just keeps turning
if you remove the crank shaft senser at the front of the engine ,between the engine and gearbox , the tip of it will be missing ,this is due to excessive end float in the crank shaft due to worn thrust washers,

Apr 17, 2010 | 2001 Ford Focus

1 Answer

Cut off when I put my foot on the gas. Now it will turn over and will not start
it might be the crank shaft postion senser or the cam shaft postion senser. i was having the same problem but it would stall out to when i was driving. so try that i had both replaced and have not had a problem since.

May 01, 2009 | 2000 Dodge Intrepid

Not finding what you are looking for?

View Most Popular

2003 Impala

  • Cars & Trucks

Related Question

93 Ranger 4.0 cranks but no start, no spark, replaced coil pack, crank shaft senser, cam shaft sensor, icu, ecm, hot to coil pack,fuel pressure good

  • Cars & Trucks

Open Questions:

0 Answers

2003 impala wipers not working. Replaced motor still nothing. Have power at plug to motor

Aug 05, 2017 | 2003 Chevrolet Impala

0 Answers

replaces ignition switch now car wont shift appears to be locked 2003 Chevy Impala

May 08, 2017 | 2003 Chevrolet Impala

0 Answers

Would a 2000 or 1999 Blazer turn signal lever be compatible with a 2003 Impala?

Apr 10, 2017 | 2003 Chevrolet Impala

0 Answers

where is the fuse for 2003 impala

Mar 29, 2017 | 2003 Chevrolet Impala

See all 2003 Chevrolet Impala Questions

Related Topics

2003 Chevrolet Impala Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

2010 Chevrolet Impala

2005 Chevrolet Impala

2007 Chevrolet Impala LS Sedan...

2005 Chevrolet Impala

2005 Chevrolet Impala

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
. 2003 Impala Manual

2003 Impala

Loading...