Question about 1996 Ford Probe

1 Answer

Hello i have a ford probe gt 1996 the check engine wont go out the code it gives me is 1195 exaust gas pressure sensor where and what is that thank you.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi that exact error code comes back as being a fault with the egr valve now the chances are getting it changed will solve the problem
there could be a few diferent things wrong with the egr.-damaged sensor-damaged solenoid-improper harness conection-improper or damaged hoses-open/short in harness-damaged powertrain control module(PCM). oh and for where it is stand in the front of the car in the middle lean to the very back of the engine and you will se the throttel positioning sensor an inch behind that is the egr postioning valve and 3 inches to you'r left is everything els good luck!

i hope that gives you some help on finding the egr valve/sensor getting this replaced should solve your problem

let me know if you need further assistance ok

you can also google how to replace egr valve on ford probe and that will then list loads of sites that should give you step by step instructions on doing this.

it will be in the workshop manual if you have one of them if not use google and you should find loads of guides that can help you

Posted on Oct 01, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there a simple way to tell if a crank sensor on a 1996 ford probe gt 24 valve engine is stopping it from starting?

If you have fuel injector pulse, engine cranking, I don't think the crank sensor is your problem. Just my opinion.

May 01, 2017 | Ford Cars & Trucks

1 Answer

My car ford 1996 probe have the code 1195 how do I fix the problem ???

The code P1195 is a SCP HBCC Failed to Initialize.

Jun 04, 2015 | 1996 Ford Probe

1 Answer

My 1996 Ford Probe will crank but wont start. After 3 to 35 minute wait it will start. Sometimes it will drag the battery down and I have to wait for it to re-energize, then it will start. What is the...

Once you get your Ford to start, does the engine run normally ? If yes, then timing not an issue. If no, you may consider timing, but not until other components have been checked.
Have you done any maintenance to your vehicle like a tune up, air filter / fuel filter change. Have you checked fuel pressure ?
Have you checked for any codes in the engine control module ?

Jul 24, 2017 | 1996 Ford Probe

1 Answer

I have a ford ranger and the diagnostic code coming up is p1400 evg low voltage...ranger is 1998...

Ok.. The code P1400. Is. Related with the E.G.R system.
" Exaust Gas Recirculation"
The code P1400 is Exactly.
Sensor DPFEGR low voltage.
This code can set for.
Leaking up-strim pressure hose.
DPFEGR sensor Short to ground or signal return circuit.
VREF selenoid shorted to ground or signal return circuit.
Faulty DPFEGR .
or In the last case faulty PCM.

Ok.. The DPFEGR is a little box Located at the intake manifold.
to identificate See the Exaust Manifold Gasket you will see.
2 Little hoses Goin at the little box. When you found.
Check the hoses for cracked or damaged repair as need.
Check the connector.
The VREF. to locate follow the Little vaccum hose GREEN.
Goin to the EGR attached at the Intake manifold .
and check the connection.
If everything is OK. I recomend to replace the DPFEGR.

NOTE. If you don't have enought Expertise on vehicles.
I recomed to consult with your mechanic. and maybe give this information.
But if you can do your self go ahead.

I hope this help on your question. THANK YOU FOR USE FIXYA..

Dec 01, 2009 | 1998 Ford Ranger SuperCab

2 Answers

Looking for a picture of the engine of a 1996 ford probe

no, if the oil pressure is eratic the first thing i would check is the oil pump. unless lots of black smoke is coming out the tail pipe. in that case your engine seals are bad and you will have to do a compleate rebuild on the engine.

Aug 14, 2009 | 1996 Ford Probe

2 Answers

96 mustang gt wont stay on unless im giving it gas

Since the date in this post was a few years ago, I'm just gonna put it on here for someone else who may encounter the same issue. My '96 did the same exact thing. It was IAC (idle air control) valve. $50 and runs perfect...

Nov 29, 2008 | 1996 Ford Mustang

1 Answer

Over heating

When you are running the car,do the cooling fans come on? What was the reason for replacing the radiator? After you installed it did you have the system pressure tested? Something as simple as a bad radiatior cap can cause an overheat.Another thing to check is the temperature the coolant temp sensor is sending to the on board computer. The noise you are hearing, is it coming from the valve cover? Send the info back and include the engine and the transmission type. Thanks

Sep 01, 2008 | 1996 Ford Probe

Not finding what you are looking for?
1996 Ford Probe Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides