Question about 2001 Mercury Grand Marquis

1 Answer

How do i or what tools do i need to remove the rear wheel hub on a 2001 mercury grand marquis with abs. can't find the puller or proceure anywhere.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 5,332 Answers

The rear wheels do not have a hub. They have an axle and and axle bearing.

The axle can be removed by removing the differential cover. there will be a bolt that holds the differential pin in place. Usually a 5/16 or 8mm wrench will work to remove it. Once the pin is out the axle can be pushed in from the outside of the vehicle and the c-clip can be removed. Do not rotate anything with the dif pin removed or the spider gears will fall out of place. Once the c-clip is removed the axle will pull out of the axle housing.

If you need to replace the bearing that the tool you need is called an an axle bearing remover. You will also need a slide hammer in order to use this tool. To install the new bearing you will need a tool called a bearing/race driver and a hammer.

Posted on Oct 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a clicking noise in the right rear of my 2005 Mercury Grand Marquis. It sounds like it clicks in time with the tire rotation


There are brakes shoes inside your rotor , they are for the emergency brake, lightly apply the e brake see if it changes the noise it may go away after you take. It off, rust builds up in ther

May 04, 2015 | 2005 Mercury Grand Marquis

Tip

How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02...


How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02 1AAuto.com

on May 22, 2012 | 2001 Mercury Grand Marquis

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

I have a 2007 grand caravan front wheel drive that needs a new rear bearing hub assembly. I have removed all except the assembly and it will not budge. Is there anything I can use to remove the hub other...


CHRYSLER WARNED AGAINST NOT USING A SLIDE HAMMER PULLER UNLESS YOU ARE GOING TO REPLACE REAR HUB AND BEARING ASSEMBLY.WHEN REPLACING HUB AND BEARING ASSEMBLY THEY HAS TO BE PRESSED OUT.

Sep 21, 2010 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

What can i do to remove the pitmanarm when the pitmanarm puller a twojaw puller heating it with a torch banging it with a hammer have not worked


you need to buy or rent a pitman arm puller. lock the steering wheel on center. try pulling with puller, put tension on arm with puller, heat and rape it. it should pop loose.

Jul 14, 2010 | 2000 Mercury Grand Marquis

1 Answer

Marquis traction control problems .If car is excelerated from 20k the left wheel locks up and the car goes out of control.ON ice at a standing start the rear wheels lock up.


your abs sensors are acting up re set the sensors by loosening the screws and find the proper spacing(dealer) or remove the sensors alltogether

Dec 16, 2009 | 1994 Mercury Grand Marquis

2 Answers

How to replace a fuel filter in a 2001 mercury grand marque v eight g s?


the fuel filter is located inside the frame rail on the passenger side, sort of underneath the rear seat. there are two plastic lines on either side with quick release fittings. i believe its held on my a gear clamp style holder. not too difficult to change.

Dec 11, 2009 | 2001 Mercury Grand Marquis

2 Answers

How do you change the rear brakes on a 1994 Mercury Grand Marquis? The problem is with the passenger rear, it appears out of round. I replaced the rotor and pads the piston looks like it is seated properly...


Remove the rear wheel, you now have access to the brake drum. to remove it may be another story. There may be a few obstacles. First may be adjustment: You need to access the the backing plate, and remove the rubber plug if equipped. Then using a brake adjusting tool, back off the adjuster. It this still does not release it may be because of 2 more possibilities, one is a frozen drum to the hub (take a large hammer and hit between the studs-DON'T HIT THE STUDS. Second may be a worn drum from the linings wearing into it. Take it to a pro at this point, you may still lose the shoes or hardware in the process.

Oct 11, 2009 | 1994 Mercury Grand Marquis

1 Answer

I have a 2003 mercury marquis. Both rear hubs


If you have the caliper and retaining rings off the park brake must be holding it. This vehicle has small parking brake shoes that apply to the inside of rotor hat. Try backing off the adjustment and tap the sides of the hat to free them up.

Mar 22, 2009 | 1996 Mercury Grand Marquis

Not finding what you are looking for?
2001 Mercury Grand Marquis Logo

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...