Question about 1997 GMC Yukon

1 Answer

Disconnecting brake pedal from brake booster.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GMC Master
  • 76,682 Answers

There is no bolted connection, just a rod that pushes from the brake pedal arm into the vaccum booster push rod socket

Posted on Oct 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996Chevy K1500 Silverado, replacing the vacuum brake booster... what is the trick to getting the booster rod disconnected from the pedal?


go under the dash and remove the split pin from the shaft and pull the shaft out of the brake pedal

May 22, 2016 | Cars & Trucks

1 Answer

REPLACE A BRAKE BOOSTER FOR A PONTIAC 1997 SUNFIRE


without undoing the brake lines undo the nuts that hold the master cylinder to the power booster and move it out of the way. then disconnect the vacuum hose to the booster then under the dash disconnect the brake pedal rod that connects the pedal to the booster then unbolt the 4 nuts that fasten the booster to the firewall. remove the booster.

Sep 06, 2014 | Pontiac Sunfire Cars & Trucks

1 Answer

Replace brake booster


You will have to drain and remove the master cylinder. Remove vacuum lines from booster. Than disconnect your brake pedal from the brake booster. This in done from inside the car. After you disconnect your brake pedal, there should be four nuts that hold the booster the the bulk head. Remove those and carefully remove booster from car from under the hood. Install in reverse order and bleed your brake system.

Feb 17, 2014 | 2001 Nissan Quest

1 Answer

Step by step instructions for replacing brake booster on a 1999 Toyota Camry


its my pleasure to answer your question how to replace the brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How to remove brake booster on 1999 Toyota Camry


The following steps will help you to replace a Toyota Camry brake booster :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Oct 04, 2013 | Cars & Trucks

1 Answer

How do i replace the brake booster on a 98 Mercury villager


12 specific steps will help you :
1 With the engine off, step on the brake pedal several times to relieve the brake booster of vacuum.
2 Press the brake pedal down and start the engine. Verify that the brake pedal sinks slightly. Turn off engine.
3 Remove the vacuum hose from the brake booster.
4 Remove the brake lines from the master cylinder. Remove the master cylinder from the brake booster. Plug the fittings to prevent brake fluid seepage.
5 Disconnect the brake pedal from the push rod.
6 Have an assistant hold the brake booster from inside the engine compartment. Remove the nuts that hold the brake booster to the firewall. These nuts are usually located under the dash on the interior of the firewall.
7 Remove the brake booster.
8 Install the new brake booster to the firewall. Tighten the mounting nuts.
9 Connect the push rod to the brake pedal.
10 Connect the vacuum hose to the vacuum brake booster.
11 Attach the master cylinder to the new brake booster and reconnect the brake lines.
.12 Bleed the brakes at the master cylinder.

Sep 24, 2013 | Cars & Trucks

1 Answer

How to replace brake booster on 96 gmc 1500


Remove brake master ! Two bolts holding it to the booster disconnect vac hose ! Now go in the truck follow the brake pedal up remove the pin the connects the pedal to the booster ! There will be 4 bolts holding the booster in place! Once bolts are out push booster out gently!

Oct 05, 2011 | 1996 GMC Yukon

2 Answers

How do i change a brake booster


from autozone.com:

  1. Disconnect the negative battery cable.
  2. Apply the parking brake.
  3. Unplug all necessary electrical connections.
  4. Remove the master cylinder from the booster and pull it off the studs, CAREFULLY! It is not necessary to disconnect the brake lines.
  5. Disconnect the vacuum hose from the check valve.
  6. If necessary, remove the brake light switch.
  7. Disconnect the booster pushrod at the brake pedal.
  8. Remove the booster mounting nuts, located on the inside of the firewall.

24cafd9.gif


Fig. Fig. 1: Vacuum booster mounting

  1. Lift off the booster and remove the gasket.

To install:
  1. Install the booster with a new gasket.
  2. Tighten the booster mounting nuts to 21 ft. lbs. (29 Nm) on all except 1996-98 models. On 1996-98 models, tighten the nuts to 26 ft. lbs. (36 Nm).
  3. Install all remaining components.

Oct 29, 2010 | 1998 Chevrolet Blazer

1 Answer

How do you install brake booster on 1998 chevrolet suburban 1500


Press brake pedal several time to exhaust pressure from accumulator, Clean dirt from hydrulic line connections at booster and at master cylinder.Disconnect hydraulic lines from booster and plug all openings. Note; in most cases it is not necessary to disconnet master cylinder brake lines to remove booster.Remove and support master cylinder.Disconnect booster push road from brake pedal. remove booster to firewall nuts from inside vehicle.Remove booster and gasket

Aug 17, 2009 | 1995 Chevrolet K1500

1 Answer

Need to replace a brake booster on a 1998 chevy cavalier


get ready for some work.you need to remove the master cylinder nuts that hold master cylinder to brake booster.once you remove nuts you have 2 choices remove master cylinder to remove booster. to keep from bending brake lines.or you can leave master cylinder in pull it toward you easily careful dont bend lines .disconnect vacuum line at booster .go inside vechicle to floor on driver side loosen four nuts on floor to booster .disconnect power brake push rod from brake pedal .dont force pushrod to the sides when disconnecting it.remove four booster nuts then remove booster.when in stalling the new booster loosely install four nuts then connect the push rod to the brake pedal .install new clip tighten the booster unit .if you decide to remove master cylinder use inline wrenches on master cylinder to remove lines.also plug the master cylinder brake line holes to keep from losing all brake fluid.

Apr 26, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1997 GMC Yukon Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...