Question about 1999 Toyota Corolla

1 Answer

How to adjust rear brakes shoes on toyota corrolla 1999

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 343 Answers

The shoes on drum brakes should auto adjust by backing up and applying pressure to the brake pedal (you may hear a clicking noise from the springs on the adjustment stars as they turn). If this does not work, the mechanism may be broken, aligned improperly or stuck by corrosion. Most drum brake assemblies have an access hole in the drum or backing plate to make manual adjustments, comment back to me if u have these access holes and I will walk you through the procedure...(check your shoe lining thickness as you may just need new brake shoes)

Posted on Oct 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spongey brakes, i have already replaced the front pads 2009 corrolla


Your drum brakes need to be adjusted first, most likely the pre-travel of the shoes is making the pedal feel soft. If it is still soft after shoe adjustment, you either have air in the system or possibly a bad master cylinder.

Jun 23, 2014 | 2003 Toyota 4Runner

1 Answer

I put new brakes in my saturn. i put new front calipers,rotors and pads and power bleed front only. i also put new brake pads in rear but did not replace drums.after all that i can't get a hard brake...


try adjusting the rear brake shoes but.....spin the rear wheels first is u get the feeling of the shoes grabbing then releasing ( the tire gets loose then tight as u rotate it) u will need to have the drums cut on a brake lathe or replaced...when u have this done , then adjust the rear shoes until u get a slight drag on the rear wheels..go pump the brake pedal to seat the shoes if the wheel spins free adjust the shoes more an repeat until they have a slight drag after pumping the brake pedal

Jul 16, 2011 | 1999 Saturn SL

1 Answer

Replaced shoes on 1988 Toyota Pickup 2 wd, breaks will not stop wheels...what could this problem be?


I assume the rear shoes where replaced,was this a problem before replacing the rear shoes?Adjust the rear shoes out to where the wheel drags just a littl when turning it by hand,then if you need to,bleed the brakes,bleed the master cylinder,then the right rear,left rear,then right front,and left front,do not run out of brake fluid during this proccess.

Apr 11, 2010 | 1988 Toyota Pickup

1 Answer

How to remove rear abs sensor from rotor a 99 dodge intrepid


Raise and support the vehicle. Remove the rear wheel hub and bearing with a socket wrench. Back the parking brake shoes away from the rotor using the adjuster star wheel. Remove the parking brake shoe adjuster spring and the shoe adjuster with a socket wrenchDisconnect the hold-down clip and pin for the upper brake shoe so you can remove the upper shoe from the actuator lever with a socket wrenchRemove the return spring from the lower brake shoe and disconnect the shoe actuator lever from the end of the parking brake cable. Detach the hold-down clip and pin from the lower brake shoe and remove the lower brake shoe with a socket wrench.

Oct 09, 2009 | 1999 Dodge Intrepid

1 Answer

Mazda protege 1999 rear brake replacement


Have you adjusted the adjuster to bring the shoes close to the drum? Always force the pistons in (the return springs should hold them in) and then adjust to make a tight fit after replacing. When the shoes are on right, there is no way for the piston to come out, as there is only a quarter inch of travel.

Jul 27, 2017 | 1999 Mazda Protege

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

1 Answer

I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


Drum, Rear Brake System Standard Rear Brake
9969082.gif
Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake
6dcb5d2.gif
Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:
  • Have internal shoes that expand against the brake drum (1126).
  • Are a single-anchor type.
  • Are actuated by one rear wheel cylinder (2262).
  • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
  • Adjust rear brake shoes and linings (2200) automatically.
  • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Apr 04, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Rear brakes scrubbing on 1998 chevy venture van


Removal Procedure Tools RequiredJ 38400
Caution: Keep fingers away from rear brake shoe springs to prevent fingers from being pinched between spring and shoe web or spring and backing plate.
  1. Remove the brake drum. Refer to Brake Drum Replacement

  2. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  3. Use the J 38400 in order remove the adjuster spring (1). Disengage the adjuster spring loop from the tab on the adjuster actuator.
  4. 2.1. Remove the loop end of the adjuster spring from the adjuster actuator. 2.2. Remove the straight end of the adjuster spring from the secondary brake shoe.
    142293.gif
    tif.gif
  5. Use the J 38400 in order to spread the brake shoes apart.
  6. Remove the adjuster.
Installation Procedure

    142293.gif
    tif.gif
  1. Use the J 38400 in order to spread the brake shoes apart.

  2. 178990.gif
    tif.gif
    Important: Ensure that the adjuster (2) engages the brake shoes (4 and 5), the park brake actuator (3), and the adjuster actuator (1) properly.
  3. Install the adjuster.

  4. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  5. Install the adjuster spring (1).
  6. 3.1. Install the straight end of the adjuster spring into the secondary brake shoe. 3.2. Install the loop end of the adjuster spring to the adjuster actuator.
  7. Install the brake drum.

Dec 06, 2008 | 1999 Chevrolet Venture

3 Answers

Remove rear brake drums


0f2c8a8.gif
1. After removing the wheel, remove the brake drum. 2. Remove the shoe hold down spring, the automatic adjuster spring and adjuster lever.
7b7d17f.gif
3. Spread the shoes and remove the shoe adjuster. 4. Remove the shoe to shoe spring and shoe hold down spring.
a1a62c3.gif

Jun 03, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
1999 Toyota Corolla Logo

754 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...