Question about 2002 Jeep Liberty

1 Answer

Change the right rear tail light bulb. - 2002 Jeep Liberty

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

I suggtes check in the Repair Manual, in this LINK for the Section 8L LAMP (page 464 and next).

I hope help with this answer (remember to rate it).

Posted on Oct 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

RIGHT INDICATOR AND REAR RIGHT BRAKE LIGHT NOT WORKING BUT THE BULBS ARE OK


There must be a "Fairlure (light) Sensor" in or around the rear lights. This tiny circuit can be on the left side of the tail-light or on the right side of the tail-light. Pull out both sides, and only one side has a tiny box with the circuit in it. This circuit is a safety thing to let you change the bulb, but when this circuit is bad, you will have to replace that particular tail-light, unless you want to by-pass the circuit.

Oct 04, 2017 | Cars & Trucks

1 Answer

How to replace, step by step, the rear brake light bulb on hyundai atos 1999?


How Do You Change Tail Light Bulb
Remove the wiring harness from the tail light lens assembly. Disconnect tail light bulb from the wiring harness socket. Reconnect the wiring harness to the tail light lens assembly. To confirm proper installation of the new tail light bulb, place the key in the on position.
IT IS VERY SIMPLE OR GO TO AUTOZONE AND HAVE THEM CHANGE IT OUT FOR YOU AND WATCH THEM ONCE. GOOD LUCK.

Jul 01, 2015 | Hyundai Cars & Trucks

1 Answer

Right rear turn signal does not work


check the bulb there some bulbs have two elements in them the turn signal element might be broken change the bulb

Sep 19, 2012 | Cars & Trucks

1 Answer

HOW DO YOU CHANGE THE REAR TAIL LIGHTS ON A 1998 CROWN VIC?


Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

Jul 05, 2011 | 1998 Ford Crown Victoria

1 Answer

Rear left Tail light not working. left rear Brake light works . Right side works


tail light is seperate filament inside the brake light bulb- change bulb

May 10, 2011 | 2006 Chrysler Pacifica

1 Answer

How to replace right rear taillight assembly


Access to the tail light cluster should be through panels in the rear corners of the vehicle. Remove the panel and you can remove the tail light cluster to replace the bulbs. This is the position on most sedans, unless, like on pick-ups, the tail light lenses have screws which allow the lenses to be removed to change the bulbs.

Apr 01, 2011 | 2002 Lexus RX 300

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

2 Answers

How do you take the right rear tail light out to


Raise lift gate, remove two screws from assy., and pull light assy. out, twist bulb counter clockwise. reverse procedure to install.

Sep 17, 2009 | 2005 Dodge Caravan

4 Answers

Change rear signal bulb on 2002 ford focus wagon


Open the rear tailgate There are 2 screws that hold light housing in place.. Remove the screws then pull the housing outwards till the clip behind it springs. You then need to knock the housing sideways (outwards) to free the 2 prongs that attach housing to the car body.
Unclip the rear housing from the back of the light unit & change the bulb.

Aug 01, 2008 | 2002 Ford SVT Focus

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...