Question about 2007 BMW 525xi Sedan

1 Answer

BMW remote control problem

No powers lock by remote.
Can not open/close the car by remote control.
All doors can be opened/closed by using the key from remote.
From inside can opened/closed the doors by using the board lock switch.
Radio and navigation system works fine.
Both remote controls are not working.

Posted by on

  • 10 more comments 
  • Michael Ca Aug 20, 2008

    I have the same problem with my 2003 BMW 330cic. Both remote keys do not work to lock/unlock the doors and the trunk. Any potential solutions?



  • Anonymous Feb 04, 2009

    Try to reinit your key, go into car ,close dor, turn the key on and off 2 times quick (2-3 sec.) press unlock button and keep pressed and press short 3 times lock button and release unlock button, the car confirm that whit lock and unlock dors, thats all

  • Anonymous Feb 24, 2009

    My 2005 E61 530Xi touring have the same problem. It happens after water went in the antenna amplifiers box under trunk door spoiler. It unhappy nervous problem broke some parts in amplifier board due to electrolitic short circuit.

    Solution: locate wrecked elements. (i have got 3-pole filter marked "600" under steel plate) re-solding 3-pole filter near NEC chip. Reinsulate part of board where heated with nail lacquer.

    You won't need special tool. Solder in this board is not Pb-free, so it has low melting temp.

    BMW dealer has a tech bulletin concerning this issue. 3 glue stripes could solve this problem in advance BMW means.

  • jbailey572 Mar 01, 2009

    I have a 2004 325i. I can lock the drivers side door with the remote. I cannot unlock any of the doors with the remote. all of the other doors remain locked and i have no way to unlock them. They will not unlock with the lever on the inside of the car and the little latch that pops up when the car is unlocked is too short to pull up. I can only unlock the drivers side door by inserting the key. I can pop the trunk by remote. I cannot open any door except the drivers door.

  • ludopat1272 May 11, 2010

    same problem on 2005 , 530D. ANY SOLUTION ??

  • Anonymous Mar 14, 2014

    Only boot can't be opened or locked with remote. all other doors working fine with remote

  • Anonymous Mar 15, 2014

    installed a factory remote lock system in my 1997 bmw 318ti and

  • Anonymous Mar 16, 2014

    Remote entry does not open vehicle once it has been locked for 20 seconds. Once opened with key, remote works fine. This sounds like the safe mode mentioned in the manual.

  • Anonymous Mar 21, 2014

    electric locks works on all doors apart from right rear, used to work an then sometimes and now not at all, Problem ???

  • Anonymous Mar 27, 2014

    The doors can't be open or close with remote

  • Anonymous Mar 27, 2014

    Doors wont lock or open with key buttons

  • Anonymous Mar 29, 2014

    the rear door Lock was frozen, after thet it did not work remote

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a e60 525i that I just brought and it has the same problem, the owners manual suggests driving with the key in the ignition for a long time as the batteries are rechargable and may have gone flat, i have tried this and it doesnt seem to work

i also read something about getting water in the aerial about the rear window and that wrecks the receiever. My car isn;t under warranty so not looking forwarding to taking it to bmw

Posted on Jun 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Haw to set my windows i bmw e46 to close them from key remote i can open them but not close only with key in door lock and hold :-)


Unlock but hold the unlock button on your remote while pointing at the driver's side door. There is a sensor right there.

Jul 21, 2014 | BMW Cars & Trucks

1 Answer

Having trouble with keyless remote control on 1993 lexus es300. Replace battery on remote- still not openning doors. Help Please!


Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Jan 02, 2013 | Cars & Trucks

1 Answer

1999 Ford Windstar power door locks only work when key is turned on


For Doors not getting open with remote or key problem,there are help links provided below.Click the link below to go through its procedure and troubleshoot the problem:----
drivers side front door will not open from inside or outside?

http://technoanswers.blogspot.com/2012/01/ford-f-350-crew-cab-drivers-side-front.html

----------

Car door will not close?
http://howtobyme.blogspot.com/2011/11/car-door-will-not-close.html

--------

All power door locks not working ?
http://howtobyme.blogspot.com/2011/11/all-power-door-locks-not-working-on_14.html

----------

Repairing car Door lock Actuator?
http://howtobyme.blogspot.com/2011/11/repairing-car-door-lock-actuator.html
---------------
How to Access car door panel?
http://howtobyme.blogspot.com/2011/11/how-to-access-car-door-panel.html

----------

Vehicle door panel components?

http://howtobyme.blogspot.com/2011/11/vehicle-door-panel-components.html

---------
Truck Door will not close?

http://schematicsdiagram.blogspot.com/2011/12/ford-truck-door-will-not-close.html

-----------
Where is Cars Door control Module located?

http://schematicsdiagram.blogspot.com/2011/12/where-is-cars-door-control-module.html

--------
Power door locks not working?

http://schematicsdiagram.blogspot.com/2011/12/power-door-locks-not-working.html

-----------
Door ajar light stays on?

http://technoanswers.blogspot.com/2012/01/door-ajar-light-stays-on.html

----------
Door locks not working?

http://technoanswers.blogspot.com/2012/01/door-locks-not-working-on-ford-explorer.html

----------
Front Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/front-door-dis-assembly-diagram-for.html

---------
Rear Door dis-assembly diagram?

http://repairhelpcenter.blogspot.in/2012/02/rear-door-dis-assembly-diagram-for.html

--------
How to test Power door locks?

http://repairhelpcenter.blogspot.in/2012/02/how-to-test-power-door-locks.html

--------
Doors will not open with Remote?

http://schematicsdiagram.blogspot.in/2012/02/lexus-doors-will-not-open-with-remote.html

--------

How to replace Door Hatch ?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-hatch-on-acura-integra.html

---------

How to remove Doors?

http://repairhelpcenter.blogspot.com/2011/11/how-to-remove-doors-on-acura-integra.html

-------`-

How to Replace Doors?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-doors-on-audi-a4-and-vw.html

--------

Remote will not unlock Rear door?
http://schematicsdiagram.blogspot.com/2011/12/remote-will-not-unlock-rear-door-on-gmc.html

--------

Door locks or windows not working on car?
http://schematicsdiagram.blogspot.com/2011/07/door-locks-or-windows-not-working-on.html

--------

This will help.

Thanks.

Feb 03, 2012 | 1999 Ford Windstar

2 Answers

The doors do not open by remote control key(BMW 740il 1996 model)


Programming
When
Key batteries completely discharged. Key batteries not replaced within 60 seconds. Key added or replaced. DO NOT press remote control buttons during battery replacement.
How
Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button Fig. 1 [1]. Press lock button Fig. 1 [2] briefly 3 times within 10 seconds keeping unlock button [1] depressed. Release unlock button Fig. 1 [1]. Some models: LED Fig. 1 [3] flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Some models: Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously

To change batteries remove panel back of key then screws on plastic bar
Batteries are available from your local motor factor shop
You might not need new batteries try re programing as described above

Apr 24, 2010 | 1998 BMW 7 Series

1 Answer

How can I re active the wireless remote control system ?


sit in car all doors closed put key in ignition and turn from OFF to ACC 3 times as fast as you can leaving it in ACC on the last cycle then press your remote button. your blinkers should flash to tell you this has worked.... may take you a couple of tries to get it!!

Jun 30, 2009 | 2002 Toyota Camry Solara

1 Answer

Step by step reset the door remote control lexus 400LS


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Recode a key 4 bmw 318i cenral locking


To carry out this procedure you need to have one working key and one key which requires programming. It may help sometimes to hold the key close to the rear view mirror as this is where the sensor is located in most models. 1. With both keys, get in the car and close all windows and doors. 2. Put working key into the ignition and turn to position 1 (the accessories should turn on) (try also position 2) 3. Turn the key back to position 0 and take the key out of the ignition. 4. Using the working key, hold down the unlock button, press the BMW logo (lock button) 3 times, and release the unlock button. Doors should lock and unlock. 5. With the new key, hold down the unlock button and press the BMW logo (lock button) 3 times and let go of the unlock button. Doors should lock and unlock and you're done!! If not working try the following PREPARATION 1. Close all doors, trunk, hood and sunroof. 2. The security system must be in 'disarm' mode. The key must be removed from the ignition key slot. ENTER CODE LEARNING MODE 3. Open trunk and leave it opened. 4. Open the drivers door and sit in the drivers seat. 5. Close the drivers door. 6. Cycle the ignition switch 5 times between the 'OFF' position and position 2,(ignition 'ON', all dash warning lamps will illuminate). The red status LED will illuminate continuously, and the siren will 'chirp' once, to indicate that the code-learning mode has been initiated. ?Do No start the engine.? The Ignition switch cycling in step #6 must be performed within 10 seconds. The sequence in steps #1-#6 must be performed within 45 seconds. REGISTER/DELETE ID CODE(S) 7. Open drivers door, (remain seated in the drivers seat) 8. Close the drivers door. 9. Press and release any button on the remote you wish to register in the system. The status LED will shut off momentarily to indicate that one code has been registered. 10. Repeat steps 7 thru 9 to register the three ID codes. It is possible for the system to memorize a total of 4 different ID codes. As a new code is initialized into the memory, the oldest code is automatically deleted. If you had lost your remotes and wished to delete the lost remote ID codes from the memory, you could initialize the ID codes from a newly purchased replacement transmitter four times thereby deleting the previous ID codes from the system memory. EXITING CODE - LEARNING MODE: 11. Open drivers door, and exit from the vehicle, leaving the door opened. 12. Close trunk. 13. Close drivers door. The LED will turn off and the siren will 'chirp twice. 14. The initialization procedure is now completed; Test all remotes to confirm operation. If this doent work your alarm/central lock needs to be reset

Mar 28, 2009 | 1996 BMW 318

3 Answers

The Lexus car remote key control model ES300


try this:

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (DO NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Mar 23, 2009 | 1997 Lexus ES 300

1 Answer

Programming keyless remote


2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Jul 12, 2008 | 2003 Mazda Mazda6

Not finding what you are looking for?
2007 BMW 525xi Sedan Logo

5,141 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...