Question about 1988 Pontiac Fiero

2 Answers

How to remove camshaft gear without removing camshaft

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

NOT TRUE.. You can break the old gear off as it is not needed, make sure you put a rag or something over the oil pan opening, grind the little metal piece in the middle off, heat the new gear in an over at 400 degrees for a half hour with 10 mins left ice the end of the cam and the new gear will slip on like butter.

Posted on Oct 20, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 72 Answers

The camshaft gear on the 4 cylinder engine is pressed on you need to remove the camshaft to press the gear off. it would be damaged if you try to do it in the engine.

Posted on Jan 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NEED DIAGRAM FOR LOCATIONS OF CRANKSHAFT PULLY,OIL SLINGER AND SPRING.FOR 1983 MAZDA 2.2L DIESEL


Here is the procedure:-


  1. Remove setscrew from side of cylinder block.


  2. Remove oil pipe attaching bolts.


  3. Remove oil pump and strainer.
TIMING GEAR COVER



  1. Remove timing gear cover to case attaching bolts.


  2. Remove timing gear cover and gasket.

CAMSHAFT, CRANKSHAFT, IDLER & INJECTION PUMP GEARS



  1. Remove oil slinger and washers from crankshaft snout.
Using puller set 49 0839 425C or equivalent, remove crankshaft timing gear, Fig. 3.


  1. Position a clean rag between camshaft and idler gears, then remove cam gear lock bolt and washers.


  2. Using puller set 49 0839 425C or equivalent, remove cam gear from camshaft, Fig. 3.


  3. Remove idler gear to spindle retaining nuts and washers, then remove idler gear and spindle assemblies.


  4. Remove injection pump drive gear.


  5. Remove timing gear case to cylinder block attaching bolts, then the timing case.



CAMSHAFT




  1. Remove tappets from cylinder block.


  2. Remove camshaft thrust plate to cylinder block retaining bolts and washers, then pull camshaft from block.



PISTON & CONNECTING ROD




  1. Remove connecting rod bearing cap retaining nuts and bolts, then separate bearing cap from connecting rod.


  2. Using the wooden handle end of a hammer, push the piston and connecting rod assembly outward until piston rings clear cylinder bore. Remove piston and connecting rod assembly through top of cylinder block.


  3. To separate piston from connecting rod, remove piston pin retaining clips, then press pin from piston using a suitable driver.



CRANKSHAFT




  1. Remove rear oil seal cap retaining bolts, then the cap and seal.


  2. Remove main bearing cap to cylinder block retaining bolts, then the main bearing caps and thrust washers.


  3. Lift crankshaft from cylinder block.

Mar 26, 2015 | Mazda Cars & Trucks

Tip

Escort 1.9L Timing Belt Replacement


Remove the serpentine belt, remove the lower crankshaft pulley, place a jack under the oil pan and jack up the engine slightly, remove the engine mount (right top). Remove the timing belt cover, loosen the timing belt tensioner and pull tensioner pulley back toward the rear of vehicle. I like to then tighten the tensioner bolt to hold it in this position, remove and replace belt. If you need to put the engine in time then look at the camshaft there is a small arrow in the center, it lines up with a dot on the end of the cylinder head. The lower timing mark is a small metal tip that sticks out from the lower gear, and it lines up with a notch cut into the front cover just behind the lower gear. Once aligned properly put the belt on the lower gear and without turning the lower gear or camshaft gear pull the belt tight up to the cam shaft the cogs in the belt will line up with the grooves, then place the belt around the water pump drive gear and under the tensioner, then push the belt over all gears by hand without turning the engine. Loosen the tensioner bolt and apply a little pressure toward the front of the vehicle and tighten the bolt. Replace everything else previously removed. Engine should start and run normally.

on Aug 10, 2010 | Ford Escort Cars & Trucks

1 Answer

Timing set


Chain

Print


REMOVAL & INSTALLATION

4.3L, 5.0L, 5.7L and 7.4L Engines
See Figures 1, 2, 3, 4, 5 and 6

  1. Remove the timing cover. This will allow access to the timing chain.
  2. Crank the engine until the timing marks on both sprockets are nearest each other and in line between the shaft centers.



0996b43f80219aca.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Crank the engine until the timing marks on both sprockets are in line

  1. On 1996-98 vehicles remove the crankshaft position sensor reluctor ring, if equipped. On 7.4L engines tool J-41371 or its equivalent puller must be used to remove the reluctor ring.
  2. Take out the bolts that hold the camshaft gear to the camshaft. This gear is a light press fit on the camshaft and will come off easily. It is located by a dowel. The chain comes off with the camshaft gear.



0996b43f80219acb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Remove the camshaft gear retaining bolts


0996b43f80219acc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the camshaft gear and timing chain
A gear puller will be required to remove the crankshaft gear.
To install:

  1. Without disturbing the position of the engine, mount the new crankshaft gear on the shaft, and mount the chain over the camshaft gear. Arrange the camshaft gear in such a way that the timing marks will line up between the shaft centers and the camshaft locating dowel will enter the dowel hole in the cam sprocket.
  2. Place the cam sprocket, with its chain mounted over it, in position on the front of the truck and pull up with the three bolts that hold it to the camshaft.
  3. After the gears are in place, turn the engine two full revolutions to make certain that the timing marks are in correct alignment between the shaft centers. Tighten the camshaft sprocket bolts (and nut on the 4.3L) to 21 ft. lbs. (28 Nm) on 1988-95 models. On 1996-98 models, tighten the bolts to 18 ft. Lbs. (25 Nm). On the 7.4L, tighten them to 20 ft. lbs. (26 Nm) on 1988-95 models. On 1996-98 models, tighten the bolts to 25 ft. Lbs. (34 Nm).

When installing the crankshaft position sensor you must use install a new oil ring seal onto the sensor.
  1. Install the crankshaft position sensor reluctor ring (if equipped), onto the crankshaft until it is firmly seated against the crankshaft sprocket. On 1996-98 7.4L vehicles replace the reluctor ring with a new component.
  2. Install the front cover, torsional damper, water pump and the radiator.



0996b43f80219acd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: A gear puller will be required to remove the crankshaft gear


0996b43f8020d5d9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Timing mark alignment-4.3L, 5.0L, 5.7L and 7.4L engines

Apr 20, 2013 | 1993 Chevrolet Suburban

1 Answer

On a 1985 f150 where would a camshaft sensor be


Check this procedure... REMOVALand& INSTALLATION

6-300
  1. Remove the grille, radiator, and timing cover.
  2. Remove the distributor, fuel pump, oil pan and oil pump.
  3. Align the timing marks. Unbolt the camshaft thrust plate, working through the holes in the camshaft gear.
  4. Loosen the rocker arms, remove the pushrods, take off the side cover and remove the valve lifters with a magnet.
  5. Remove the camshaft very carefully to prevent nicking the bearings.
  6. Oil the camshaft bearing journals and use Lubriplate or something similar on the lobes. Install the camshaft, gear, and thrust plate, aligning the gear marks. Tighten down the thrust plate. Make sure that the camshaft end-play is not excessive.
  7. The last item to be replaced is the distributor. The rotor should be at the firing position for no. 1 cylinder, with the timing gear marks aligned

V6 and V8 Including Diesel
Ford recommends removing the diesel engine for camshaft removal.
  1. Remove the intake manifold and valley pan, if so equipped.
  2. Remove the rocker covers, and either remove the rocker arm shafts or loosen the rockers on their pivots and remove the pushrods. The pushrods must be reinstalled in their original positions.
  3. Remove the valve lifters in sequence with a magnet. They must be replaced in their original positions.
  4. Remove the timing chain/gear cover and timing chain (timing gear on V8 diesel) and sprockets.
  5. In addition to the radiator and air conditioning condenser, if so equipped, it may be necessary to remove the front grille assembly and the hood lock assembly to gain the necessary clearance to slide the camshaft out of the front of the engine. On the V6-3.8L, remove the camshaft thrust button and spring. Remove the camshaft thrust plate attaching screws and carefully slide the camshaft out of its bearing bores. Use extra caution not to scratch the camshaft lobes.
Camshaft removal tools, Ford part no. T65L-6250-A and adaptor 14-0314 are needed to remove the diesel camshaft.
  1. Coat the camshaft with engine oil liberally before installing it. Slide the camshaft into the engine very carefully so as not to scratch the bearing bores with the camshaft lobes. Install the camshaft thrust plate and tighten the attaching screws to 9 - 12 ft. lbs. Measure the camshaft end-play. If the end-play is more than 0.009 inch; (0.228mm), replace the thrust plate. Assemble the remaining components in the reverse order of removal.
Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day

Dec 19, 2011 | 1985 Ford F150

1 Answer

Replacement of timing belt on 2001 daiwoo legansa


This should give you a clue as to how to replace the timing belt on the camshaft pulleys.prev.gif next.gif Camshaft and Valve Lifters REMOVAL & INSTALLATION 1.6L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Camshaft Position (CMP) sensor connector
    • Spark plug wires from the plugs
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in the sequence illustrated.
  8. Remove the caps and the camshafts. Fig. 1: Loosen the camshaft cap bolts in this sequence using several passes - 1.6L engine 9307zg85.gif
    To install:
  9. Lubricate the camshafts and caps with engine oil.
  10. Install the caps and the camshafts in their original positions.
  11. Tighten the camshaft cap bolts in the sequence illustrated to 12 ft. lbs. (16 Nm). Fig. 2: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 1.6L engine 9307zg84.gif

  12. Measure the camshaft endplay on both camshafts. The endplay should be 0.003-0.009 in. (0.10-0.25mm).
  13. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  14. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  15. Apply a small amount of gasket sealer to the corners of the front camshaft caps and to the top of the rear valve cover-to-cylinder head seal.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • CMP sensor connector
    • Crankcase ventilation tube to the valve cover
    • Timing belt
2.0L and 2.2L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Spark plug wires from the plugs
    • Camshaft Position (CMP) sensor connector
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated.
  8. Remove the seal ring from the camshafts. NOTE: Make sure the camshafts detaches evenly from the bearing seats in the front guide bearing.
  9. Remove the caps and the camshafts. Fig. 3: Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated - 2.0L and 2.2L engines 9307zg38.gif
    To install:
  10. Lubricate the camshafts and caps with engine oil.
  11. Install the caps and the camshafts in their original positions.
  12. Tighten the camshaft cap bolts in the sequence illustrated to 71 inch lbs. (8 Nm). Fig. 4: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 2.0L and 2.2L engines 9307zg37.gif

  13. Measure the camshaft endplay on both camshafts. The endplay should be 0.0015-0.0056 in. (0.040-0.144mm).
  14. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  15. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 71 inch lbs. (8 Nm).
    • CMP sensor connector
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • Crankcase ventilation tube to the valve cover
    • Timing belt
    • Negative battery cable

Feb 04, 2011 | 2001 Daewoo Leganza

1 Answer

How to set time on 1.9 4c


Remove the serpentine belt, remove the lower crankshaft pulley, place a jack under the oil pan and jack up the engine slightly, remove the engine mount (right top). Remove the timing belt cover, loosen the timing belt tensioner and pull tensioner pulley back toward the rear of vehicle. I like to then tighten the tensioner bolt to hold it in this position, remove and replace belt. If you need to put the engine in time then look at the camshaft there is a small arrow in the center, it lines up with a dot on the end of the cylinder head. The lower timing mark is a small metal tip that sticks out from the lower gear, and it lines up with a notch cut into the front cover just behind the lower gear. Once aligned properly put the belt on the lower gear and without turning the lower gear or camshaft gear pull the belt tight up to the cam shaft the cogs in the belt will line up with the grooves, then place the belt around the water pump drive gear and under the tensioner, then push the belt over all gears by hand without turning the engine. Loosen the tensioner bolt and apply a little pressure toward the front of the vehicle and tighten the bolt. Replace everything else previously removed. Engine should start and run normally.

Feb 03, 2011 | 1995 Ford Escort

2 Answers

2001 chev cavalier timming chain diagram


Timing Chain and Gears REMOVAL & INSTALLATION 2.2L Engine Fig. 1: The timing marks on the sprockets should be in alignment. If not, turn the crankshaft until the marks are aligned 91113p63.jpg
Fig. 2: The timing chain tensioner is retained by a Torx head bolt (1) and a regular hex head bolt (2) 91113p58.jpg
Fig. 3: Unfasten the camshaft sprocket bolt 91113p59.jpg
Fig. 4: Remove the camshaft sprocket and the timing chain at the same time . . . 91113p60.jpg
Fig. 5: . . . then remove the tensioner assembly 91113p61.jpg
Fig. 6: Compress the tensioner spring and insert a cotter pin or nail in the hole provided to hold the tensioner in position 91113p62.jpg
  1. Disconnect the negative battery cable.
  2. Remove the front cover as previously detailed.
  3. Place the No. 1 piston at TDC of the compression stroke so that the marks on the camshaft and crankshaft sprockets are in alignment (see illustration).
  4. Loosen the timing chain tensioner nut as far as possible without actually removing it.
  5. Remove the camshaft sprocket bolts and remove the sprocket and chain together. If the sprocket does not slide from the camshaft easily, a light blow with a soft mallet at the lower edge of the sprocket will dislodge it.
  6. Using a suitable gear puller, remove the crankshaft sprocket. To install:
  7. Press the crankshaft sprocket back onto the crankshaft.
  8. Install the timing chain over the camshaft sprocket and then around the crankshaft sprocket. Make sure that the marks on the two sprockets are in alignment (see illustration). Lubricate the thrust surface with Molykote® or its equivalent.
  9. Align the dowel in the camshaft with the dowel hole in the sprocket and then install the sprocket onto the camshaft. Use the mounting bolts to draw the sprocket onto the camshaft and then tighten to 66-68 ft. lbs. (91-95 Nm).
  10. Lubricate the timing chain with clean engine oil. Tighten the chain tensioner.
  11. Installation of the remaining components is in the reverse order of removal. Fig. 7: Exploded view of the timing chain and sprockets - 2.2L OHV engine 87953107.gif

Nov 11, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

Installation on 94 1.9L timing belt


Remove the serpentine belt, remove the lower crankshaft pulley, place a jack under the oil pan and jack up the engine slightly, remove the engine mount (right top). Remove the timing belt cover, loosen the timing belt tensioner and pull tensioner pulley back toward the rear of vehicle. I like to then tighten the tensioner bolt to hold it in this position, remove and replace belt. If you need to put the engine in time then look at the camshaft there is a small arrow in the center it lines up with a dot on the end of the cylinder head. The lower timing mark is a small metal tip that sticks out from the lower gear and it lines up with a notch cut into the front cover just behind the lower gear. Once aligned properly put the belt on the lower gear and without turning the lower gear or camshaft gear pull the belt tight up to the cam shaft the cogs in the belt will line up with the grooves, then place the belt around the water pump drive gear and under the tensioner, then push the belt over all gears by hand without turning the engine. Loosen the tensioner bolt and apply a little pressure toward the front of the vehicle and tighten the bolt. Replace everything else previously removed. Engine should start and run normally. Hope this helps, let me know.

Dec 26, 2009 | 1994 Ford Escort

1 Answer

Cannot get timing gear off crankshaft to replace- does not have chain.


The gear is press fit onto the camshaft. The proper way to repair it is pull the camshaft and have the gear pressed off and a new one pressed on.
At one time I had made tools to do this job without removing the cam from the engine. I no longer have the tools, they were borrowed and not returned.

Apr 13, 2009 | 1988 Chevrolet Blazer

1 Answer

1987 Buick Century 1.5 liter


You have to remove the engine covor. Then you have to remove the lifters off the camshaft. You then have to remove the Timing belt. The top gear on the timing belt has to be removed as well. then you pull the Seal out of the Camshaft. Then the Camshaft should come out. You put your new Camshaft in, then put the new seal on the camshaft. Then you put the gear back on. There is a hash mark inside of the gear, that needs to be top center. You then need to take the first spark plug out and put a screw driver in there. you then need to turn the bottom gear (where the timing belt goes) clockwise until you can feel the first cylinder come all the way up(you feel this with the screw driver). then you put the Timing Belt back on without moving any of the gears at all. The lifters have to be torqued on. They just cannot be put back on. There is a torque specification for those lifters, every vehicle is different. When you get those lifters back on, you put the lid to the engine back on. Then you are done. I hope this was helpful.

Dec 01, 2008 | 1987 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...