Question about 2002 GMC Envoy

1 Answer

How do you remove and replace the brake light switch on a 2002 GMC Envoy?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

The generic procedure is as follows :-

1. With the vehicle off, open the rear lift gate. Remove the two screws from the exposed edge of the tail light assembly.

2 Pull the tail light assembly away from the Envoy. Unplug the wiring harness attached to the assembly.

3 Remove the three screws mounting the triple bulb socket to the assembly. Pull the socket away from the assembly.

4 Pull the old brake light bulb straight up to remove it. Using gloves, insert the new bulb into the assembly.

5 Reattach the socket to the assembly. Tighten the three screws and reconnect the wiring harness. Position the assembly back in place and tighten the two screws to secure it.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Oct 01, 2010

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
hi99ins
  • 123 Answers

SOURCE: 2002 GMC Envoy Brake Lights Don't Work

It involves a little tricky manouvering under the dash to reach the switch and you need to be very aware of the orientation when fitting. PLEASE BE AWARE that you are messing with the brake pedal and if you fit this part incorrectly you could interfere with the brake pedal travel and cause a dangerous driving situation. Only fit this part once you have fully inspected the part to be removed, and preferably look at a workshop diagram. Some switches are easy some are not. Most take me 10-15 mins.

Posted on Jan 07, 2009

Doktir
  • 55 Answers

SOURCE: brake problem

Switch on brake pedal stuck due to dust etc. Many new cars have a safety feature that allow the brake-lights to come on if the brake lever is depressed, even when the ignition is switched off.
If you can get to the switch, a good cleaning with methylated spirits and a small brush should allow it to move freely again. Good luck.

Posted on Mar 09, 2009

c17hydro
  • 2984 Answers

SOURCE: Where is the interior fuse panel on my 2002 gmc envoy? Thanks!

There are two fuse boxes on a 2002 Envoy One under the Rear seat on the drivers side and one under the hood on the drivers side.

Posted on Mar 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the tail light fuse?


The tail light fuse is under the rear seat on the drivers side.

Jan 17, 2016 | 2003 GMC Envoy

1 Answer

Free 2006 gmc envoy brake light switch replacement procedure


Remove the panel under the dash. Look at the brake pedal and follow it up to the brake light switch. Two wires going to it. there is a plastic clip that holds it in place, Pull it off. The clip comes with the new switch. Replace it. To easy. Have a flash light to see..

Oct 26, 2014 | 2006 GMC Envoy

1 Answer

2002 envoy stalled going down road started right back up but had no speedometer wouldnt shift and abs and brake light came on


I had same problem with 2005 Envoy XL 4.2L
After several trips to dealer with "No problem found"....I finally found a technician that determined my ignition switch was intermittently not reading the security chip in the key.
Replaced ignition switch and problem never re-occurred.

Aug 23, 2010 | 2002 GMC Envoy

3 Answers

2004 Envoy brake lights do not come on when you push brake. The bulbs are fine


This is the part you will need to replace.
http://cgi.ebay.com/ebaymotors/AC-Delco-BRAKE-LIGHT-SWITCH-gmc-ENVOY-2003-2002-2006-/250579604910

Mar 12, 2010 | 2005 GMC Envoy Xl

1 Answer

Shifter wont disengage from park-replaced park brake switch,but no help


you need to check to make sure the brake lights work, also the brake light switch is the switch not prake-brake switch, the switch is located above the brake pedal no the bracket that holds the pedal.first thing is to check all your fuses.

Jan 29, 2010 | 2002 GMC Envoy

1 Answer

Brake lights not working on GMC Envoy 2002, checked bulbs and I think the correct fuse


On the brake pedal under dash is a switch that is actuated when pedal is depressed. depress pedal and check that the switch is being depressed. if not the switch can be adjusted by a nut on the neck of the switch. Good luck!

Oct 14, 2009 | 2002 GMC Envoy XL

1 Answer

Where is the interior fuse panel on my 2002 gmc envoy? Thanks!


There are two fuse boxes on a 2002 Envoy One under the Rear seat on the drivers side and one under the hood on the drivers side.

Mar 19, 2009 | 2002 GMC Envoy

1 Answer

Brake problem


Switch on brake pedal stuck due to dust etc. Many new cars have a safety feature that allow the brake-lights to come on if the brake lever is depressed, even when the ignition is switched off.
If you can get to the switch, a good cleaning with methylated spirits and a small brush should allow it to move freely again. Good luck.

Mar 09, 2009 | 2002 GMC Envoy

1 Answer

2002 GMC Envoy Brake Lights Don't Work


It involves a little tricky manouvering under the dash to reach the switch and you need to be very aware of the orientation when fitting. PLEASE BE AWARE that you are messing with the brake pedal and if you fit this part incorrectly you could interfere with the brake pedal travel and cause a dangerous driving situation. Only fit this part once you have fully inspected the part to be removed, and preferably look at a workshop diagram. Some switches are easy some are not. Most take me 10-15 mins.

Jan 07, 2009 | 2004 GMC Envoy

Not finding what you are looking for?
2002 GMC Envoy Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...