Question about 2003 Hyundai Tiburon

1 Answer

My keyless entry broke so when i unlock my car with my key the security system stills goes off and locks my car up so i cant start it how do i turn off the system so i can start my car

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 5 Answers

Get in the car.

Turn the key to the "ON" position (far right) and hold it there until the horn stops (usually around 30-45 seconds).

Don't start the car yet. Turn key to the "ACC" position (center) for at least ten seconds.

You should now be able to start the car again.

If this doesn't work, remember that as long as you lock the car with the key only (no remote), you can unlock it without tripping the alarm.

Posted on Oct 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you turn off an alarm for a 2005 Saturn Ion


Disarming an Armed System/Silencing an Alarm
If system arming has been requested by the keyless entry transmitter, it must be disarmed.
Important: Using the power door unlock switch or manually unlocking the doors does not disable the CTD armed mode. Also, disconnecting the battery or pulling fuses does not disable the armed mode, since the BCM stores the CTD mode status in memory.
?€¢
To disarm the CTD system in arm pending mode, SECURITY indicator flashing and doors open, perform 1 of the following:


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.


?€¢
To disarm the CTD system in the armed mode:


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.


?€¢
To disarm the CTD system when activated, alarming mode.


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.

Jun 24, 2016 | 2005 Saturn ION

1 Answer

How do you reset the alarm system on a 98 olds silhouette after it triggers without the remote entry


Theft Deterrent Arm/Disarm Modes
Important: Although mode 2 provides increased security, the content theft deterrent system disarms only by pressing unlock on the keyless entry transmitter. This can pose a problem if the keyless entry transmitter is damaged, lost, or inoperative for any reason while you attempt to disarm the content theft deterrent system.
Mode 1: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter. The system does not arm when you lock the doors with a power door lock switch.

Mode 2: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the doors with the keyless entry transmitter. The system does not disarm when you unlock the doors with the key.

Mode 3: The system arms when you lock the doors using a power door lock switch or the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter.
Changing the Feature Customization Modes
  1. Turn off the IP dimmer switch.
  2. Turn the ignition switch to the LOCK position.
  3. Remove the BCM PRGRM fuse.
  4. Turn the ignition switch to the ACC position. The BCM flashes the fasten belts indicator and sounds the chime 4 times, which indicates that BCM type 4 is installed on the vehicle. At this point, the BCM has entered the feature customization mode.
  5. In order to change the theft deterrent/shock sensor mode, turn the headlamp switch from OFF to PARK and back to OFF.
  6. The BCM flashes the fasten belts indicator and sounds the chime a number of times equivalent to the theft deterrent/shock sensor mode. A transition past mode 4 repeats the sequence starting with mode 1.
  7. Complete the following steps in order to change the theft deterrent arm/disarm mode:
6.1.
Insert the key in the left front, right front, or liftgate door lock cylinder.


6.2.
Rotate the key from the center to the unlock position.


6.3.
Press the horn button on the remote keyless entry transmitter.


6.4.
Count the number of chimes that you hear. The number of chimes tells you which mode you have set.


6.5.
Press the horn button again in order to change the mode. Continue to press the button until you hear the number of chimes that indicates the mode that you want.


6.6.
Turn the key back to the center position and remove the key from the door key cylinder.

In order to exit and save the current feature customization modes use the following procedure:

  1. Turn the ignition switch to the LOCK position.
  2. Reinstall the BCM PRGRM fuse.
If you are unable to change locking modes Theft Deterrent System Feature Customization Inoperative

Aug 25, 2015 | Cars & Trucks

2 Answers

I have a 2005 cobalt every time I open the doors the alarm goes off I replaced the battery in keyless entry but they do not work can anyone help?


You may have accidentally broke the controller. They are fragile. The newer cars like yours automatically set the alarm when the doors are locked from keychain remote, or locking manually. New remote, $50-100.

Jan 03, 2015 | 2005 Chevrolet Cobalt

1 Answer

2001 Mercury Villager keyless remote is malfunctioning


Keyless Entry
The keyless entry system consists of the following:
  • smart entry control(SEC)/timer module
  • keyless entry remote transmitters
  • power door lock actuators
  • body side door power door lock actuator
  • liftgate actuator
  • power door lock switches
  • door ajar switches
  • Principles of Operation
    All doors can be locked at once by turning the door key lock switch to the locked position. An individual door can be unlocked by moving the door key lock switch to the unlocked position and turning it again within five seconds; all the doors (including the liftgate) will unlock.
    The smart lock system is designed to keep the driver from locking his keys in the car. It will lock and then unlock all the doors if the smart entry control(SEC)/timer module detects the following conditions:
    • The ignition key still in the ignition.
    • A front door is open.
    • A door lock switch has been pushed to the lock position.
    The panic feature has a duration of 30 seconds from the last time the PANIC button is pressed. When locking the doors from the remote transmitter, the horn chirp/lamp flash feature can be disabled or enabled by holding the LOCK and UNLOCK buttons for two seconds. The hazards will flash three times to confirm that the feature has be enabled or disabled.
The control module probably see's an input that shouldn't be there . lock Switch , door ajar etc... Don't think it has anything to do with the remote . Some part stores have a tester to see if signal from the remote is working . Or the dealer ! Take it an see if your remote is sending a signal without you pressing any buttons .
If it is you need a new one .

May 19, 2017 | Cars & Trucks

1 Answer

Bought from dealer with no keyless entry. alarm activates when doors are locked with power doorlock system. alarm sounds when we open the door. how do we de-activate the alarm before unlocking the door?


Opening the drivers door with the key is supposed to shut down the factory security but the drivers key cylinder usually goes bad. You will have to unlock the rear tail gate lock cylinder with the key and that will shut down the factory security, before opening the drivers door.Your other option is to have an aftermarket keyless entry system installed, which will open the doors remotely while shut down the factory security at the same time.

Jan 25, 2011 | 1996 Jeep Grand Cherokee

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

My battery goes dead on my 1996 Lincoln Mark VIII overnight. I found that the lights come on by themself after I park the car. There is a clicking sound coming from the security module in the trunk when I...


security module in the trunk ???? There is no security module in the trunk . What light's come on by them self ? Park lamps , headlamps , brake lamps ,turn signals etc.... The module for anti-theft is under the right hand side of the dash . The remote keyless entry module is located in the trunk. Is this the part you hear clicking in ?
Door Lock Control Processor, Electronic NOTE: The electronic door lock control system will not function when the ignition switch is in the RUN or ACC position.
The electronic door lock control processor:
  • is located on the LH side of the luggage compartment.
  • contains a radio receiver that receives a signal from the keyless entry remote transmitter (15K601) through electronic door lock control processor antenna, and sends the appropriate command to the power door locks, the horn relay, the indicator flasher, or the anti-theft warning system.
  • is equipped with a battery backup which holds the programmed code in memory in the event the vehicle battery is disconnected.
    • Doors Do Not Lock or Unlock Using Keyless Entry Remote Transmitter
    • Circuit.
    • Electronic door lock control processor.
    • Keyless entry remote transmitter.
    • GO to Pinpoint Test B .

Aug 17, 2017 | Lincoln Mark VIII Cars & Trucks

1 Answer

I don't have a manual for my 2004 lincoln Avaitor but would like to know how I can change the code on the drives door key pad


KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time.

Dec 17, 2009 | 2004 Lincoln Aviator

1 Answer

2006 kia spectra. The power door locks


security ----encrypted software dealer only

Dec 03, 2009 | 2006 Kia Spectra

6 Answers

Keyless entry stopped working on 05 cobalt now i have to unlock door with the key and when i do that the alarm goes off. Help


Lock all the doors from the inside (with all the doors closed), unlock your driver's door by manually lifting the lock, then press it back down after you are out - this will prevent the alarm from sounding when you use the key to unlock the door.

Aug 02, 2008 | 2007 Chevrolet Cobalt Coupe

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

414 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...