Question about Ford Escort

1 Answer

I have a 1998 ford escort zx2 four cylinder an i just put a stater on it an while i was putting it on i accidentally broke a red and yellow wire on the harness an i dont know were it suppose to go it split out of the harness bellow starter wires

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 48 Answers

All wires in a cars harness are color coded so now carefully cut the tape back until you find the leads and then repair them. you will need to use wire connectors don't just twist them together. by the way those are the solenoid wires.

Posted on Oct 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove key cylinder on Ignition switch? 1998 ford escort zx2 2.0 four cylinder


You must remove the steering column plastic covers, they unscrew from below.

May 15, 2016 | 1998 Ford Escort

1 Answer

What would cause dimming dash lights when putting on headlights in my escort zx2


usually a bad ground wire, or something in the charging system

Sep 22, 2010 | 1998 Ford Escort

1 Answer

How to install timing belt on 1998 ford escort ZX2 2.0


put #1 piston at TOP DEAD CENTER and align your cam marks . then time igntition timing with a timing light

Jul 02, 2010 | 2001 Ford Escort ZX2

2 Answers

Timing belt broke at hiway speed Is the motor shot ? 1998 Ford Escort


Maybe not. Not all engine have an interference problem. Many wil be fine after the belt is replaced and the valve train is retimed. Was there a lot of noise? If the engine just stopped without much fanfare you are Ok. Check with your mechanic or dealer to be specific.

Feb 05, 2010 | 2001 Ford Escort ZX2

1 Answer

I have a 1998 Frord escort Zx2. when you


Make sure it is full of brake fluid first. If it is, check for leaks around the clutch master and slave cylinder. The master cylinder is mounted on the firewall below the brake master cylinder and towards the driver side. Follow the line to find the slave cylinder on front of the transmission. If you find no leaks, either the master and/or slave cylinder is bad or the clutch fingers are broken.

Jan 29, 2010 | 1998 Ford Escort

1 Answer

Ford Escort ZX2 1999, need to replace accelerator


Look at the cable routing. Figure out how to replace it. Consult shop manual or Service manual.

Sep 10, 2009 | 1998 Ford Escort

1 Answer

2002 ford escort zx2 camshaft sensor fit a 99 zx2?


Yes, All the years of the ZX2 utilize the same engine. 1998-2003 are all the same except for ECU programing and the MAF wiring. You should not have a problem.

Apr 07, 2009 | 2002 Ford ZX2

3 Answers

1998 Ford Escort ZX2 Water Pump Housing removal


I am sure the leak is the water pump based on years of Escort work, The ZX2 is equipped with a 2.0L DOHC V-Tech engine. The water pump is on the front (rt side of car) of the engine block, visible with the hood up. NAPA autoparts replacement instructions are to loosen the belt drive pulley from the pump BEFORE removing the serpentine belt. Once the four bolts are loose, take the belt off (good time to replace?) remove bolts and old water pump (four more bolts)- it will be tight, but it comes out- clean gasket area and install new gasket and pump in reverse order. That includes putting the pulley on and hand tightening the bolts, put on the belt, finish tightening the bolts to the pulley.

Aug 10, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5655 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...