Question about 1992 Cadillac DeVille

2 Answers

Bottem end has a bad main bearing.....how much to rebuild entire motor?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 4,340 Answers

It is usually cost prohibitive to rebuild.

Posted on Oct 01, 2010

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 48 Answers

This can range from $2800 on the low end with a short block and your old heads but you will put more money in it down the road. figure $4800 to do it right and do all the things that will make it last, new hoses, water pump, belts, Ing tune up, etc. .

Posted on Oct 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Got a gmc two door 4+4 4.3 v -6 -1999 lot of miles real bad knock on the bottom end of the Motor can you take oil pan off and check to see what's wrong


If you know what to, look for. It is a job within itself to remove the oil pan on this vehicle as the front diff is in the way. Most knocks on these motors are rod bearing related and if the bearing is worn bad enough, the crankshaft journal will be damaged. Most likely an entire rebuild is in store to properly repair this issue.

Jul 31, 2015 | GMC Cars & Trucks

2 Answers

Crankshaft has slack in it when you push clutch the pressure plate hits bellhousing


If the motor crankshaft has that much end play ,then
the motor has to come out, as the end thrust bearing
is gone

Need to check TSB's for that issue

Aug 28, 2013 | Hyundai Elantra Cars & Trucks

1 Answer

Replace crankshaft bearings on 1999 ford expedition


v6 have 4 main bearing sets and 6 big end bearing sets
v8 have 5 main bearing sets and 8 bigend sets
5 cylinder inline will have 6 main bearing sets and 5 big end set
It appears that some where you are short a set of bearings Check that the rebuild kit is for your engine

Feb 22, 2013 | Ford Cars & Trucks

1 Answer

Change carrier bearing on Pontiac Torrent


You must rebuild the entire rear end, all the bearings, you can't just installed the new bearing on the ring gear carrier. This bearing replacement job requires many specialized skills and many special tools to complete the adjustments required so the rear differential won't be noisy in operation.

Oct 30, 2012 | Cars & Trucks

1 Answer

Blown oil pump 3 cyclinders not firing what else can i I expect in repairing engine


If the oil pump does not work, the entire engine will lock up and be totally useless. You will need to do a complete rebuild of the engine, including main bearings and rod bearings. Sometimes it is easier to buy a rebuilt engine, in the area of $1800.00. Rebuilding will cost 800.00 plus 15 hours lablr.

Sep 27, 2010 | 1998 Buick Century

1 Answer

Engine knocks cold ok hot


if its at the top end its pistion slap
if its at the bottem end(of your engine) its a crank shaft bearing.

with out going into extream detail,

a ting sound at the top is a pistion slap.... replace all your pistions posibly over hual the engine.

a dubble knock that gose with rpm but sounds 2 knocks very every fireing of the pistion is a crank bearing..... replace your crank shaft bearings.... all of them b/c metal gose threw an engine extreamly fast and will destroy other beraings. this knock on start up will turn into a knock all the time, then a very louad knock that will end your engines life.

unfortunetly the answer is engine rebuild and fast.

May 30, 2009 | 2003 GMC Envoy

1 Answer

1.0L engine rebuild bearing cap order


On the 1.0L geo metro engine the main bearing caps go on startine with #1 at the pully timing belt end of the engine with the arrow pointing in that direction. Then #2 and so on in the same manor. Hope this helps.

Apr 07, 2009 | 1992 Geo Metro

2 Answers

I have a 96 isuzu rodeo with a 3.2 and an automatic trany... i just put in a new oil pump in it cause of it was seeming to not have enough pressure to get enough oil to the upper end of the motor... i am...


there should be an oil sending unit somewhere near the oil filter and if it is the sending unit this would have been alot cheaper then changing the oil pump

Jan 03, 2009 | 1996 Isuzu Trooper

Not finding what you are looking for?
1992 Cadillac DeVille Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...