Question about 1998 Dodge Durango

1 Answer

Breaks keep locking up - 1998 Dodge Durango

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,036 Answers

Draging brakes caused by restricted brake lines or hoses, faulty master cylinder,seizing brake calipers.parking brakes out of adjustment.in most cases faulty wheel speed sensors.will cause abs unit lock the brakes.

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why does serpentine. belt keep breaking?


Any one of the the pulleys down in front can do it. All the pulleys should turn freely. Except the lowest, center on. It is the crankshaft.

Jun 12, 2015 | Cars & Trucks

1 Answer

Hi I keep having the same problem with my land rover discovery series I, for some reason a little piece of plastic inside the door handle keeps breaking I've already replaced it once and now its broken...


I am guessing that the plastic bit is what holds the wire /rod in the hole of the lock lever It is a common connection piece in lock manufacture. If that is the case the piece that breaks is the bit that clips around the rod section(the clip fingers break off). Two fixes spring to mind is to use a piece of small wire (paper clip ) reposition the clip and tie to rod ( small zip tie may be easier) or 2 there are metal clips that do the same job( Mazda early models use these) but you could possible get them from a panel repair shop

Jun 20, 2013 | Cars & Trucks

1 Answer

Why belt keep breaking


Usually the belt is too loose, or one of the pulleys is not aligned, or one of the pulleys is locking up.

May 28, 2013 | Pontiac Grand Am Cars & Trucks

1 Answer

My rear breaks lock up at 20 mph


check the rubber hose they sometimes break inside causing it not to let fluid to to retract therefore it keeps pressure on the caliper

Mar 29, 2012 | 2000 Mercury Grand Marquis

1 Answer

Do you have to bleed the breaks if you change the break line


normaly yes as u end up haveing a air lock break pedal will keep hitting floor hope this helps cheers gaz

Mar 16, 2012 | Cars & Trucks

1 Answer

Auto theft system keeps coming on and disabling your ignition start.


the problem is probably the ignition lock cylinder. the ignition lock cylinder has two wires coming off it, after tine they will break. to repair need to replace the lock cylinder code the new lock cylinder and replace the key

Aug 26, 2010 | 1998 Cadillac Seville

1 Answer

Trying to remove ingition lock cylinder


After cover has been remove you'll see the bolts that hold the lock, when lock was install the head of the bolts are made to break off for theft reasons, get a small chisel and hit the bolt as to loosen it, once it breaks loose they'll come off easy, when installing new lock keep turning bolt till the head of the small bolt breaks off, it made to do that.

Jan 05, 2010 | 1998 Toyota Camry

1 Answer

Break calpier 2000 v 316


If rear, then parking brake possible cause.
But front and rear calipers often lock from corrosion on piston or binding on sliding parts.
Remove caliper, remove piston with compressed air or greasegun, clean corrosion, clean all grease out, replace seals. (compressed air is dangerous!)

Jun 26, 2009 | 2001 BMW 325

1 Answer

The brake caliper on my 2000 Yukon keep locking up.


I would chg. the break hose, the one from the caliper to the hard line. Break fluid runs to caliper and back thru same hose, fluid is not running back hense caliper stays compressed or locked.

May 06, 2009 | 2007 GMC Yukon

1 Answer

Breaks locking


front brake calipers are probably sticking.

Mar 09, 2009 | 1999 Volkswagen Golf

Not finding what you are looking for?
1998 Dodge Durango Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...