Question about 1993 Toyota Corolla

Open Question

How can i replace Gear Shifter Light For 1993 Corolla

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: Used toyota corolla 96' gear shifter light

There is a bulb under the shifter. It is probably burned out.

You need to purchase a number 194 bulb at an auto parts store. Next, you need to remove the entire center console to gain access to the socket that holds the bulb. This is fairly easy. After the console is removed, look under the shifter assembly to locate the socket.

A FixYa rating (4 blue diamonds) would be greatly appreciated for my assistance.

Please respond if you have any further questions.

Posted on Feb 16, 2009

  • 102 Answers

SOURCE: light in toyota corolla VE 98, automatic gear

you have to remove the screws (or bolts) inside the center console compartment. pry up the little ring around the shifter. pull up the e-brake and pull that whole assembly up. once removed there is a small 194 bulb located on the drivers side on the bottom. you should see the little black base. twist counterclockwise to remove. replace bulb and reinstall

Posted on Dec 04, 2009

  • 3 Answers

SOURCE: replacing gear shifter light bulb

The linked tutorial contains a picture tutorial on changing the gearshift light bulb. Accord Advice

Posted on Nov 27, 2009

Bray2thaden
  • 173 Answers

SOURCE: replace gear shifter bulb 1998 corolla

Remove the Middle/Cubby Hole/ E-brake cover (2 bolts and 2 screws) look under the gear shift control box towards the right, directly under the P,R,N,D,2,L. There will be a small wiring harness going into the box, you quarter twist the bulb housing out to replace.

Posted on Mar 20, 2010

Pelukes01
  • 52 Answers

SOURCE: 1993 toyota corolla how to replace watwr pump

  1. Place the water pump gasket (O-ring) on the block and install the pump. Tighten the mounting bolts evenly to 11 ft. lbs. (15 Nm). Install the timing belt covers, making sure they are properly seated and not rubbing on the belt or other moving parts. Install a new seal (O-ring) on the dipstick tube and lightly coat it with engine oil. Remove the plug and install the dipstick tube and dipstick; secure the mounting bolt to 82 inch lbs. (9 Nm).
Using a new O-ring, install the inlet pipe to the water pump.
Attach the clamps and bolts to hold the pipe in place and tighten to 7-9 ft. lbs. (9-12 Nm).
Connect the water inlet and water bypass hoses to the inlet pipe.
Install the water pump pulley and temporarily tighten the four pulley bolts.
Install the drive belts on all the pulleys and adjust all of them to the correct tension.
With the belts in place and adjusted, the water pump pulley will now resist turning. Tighten the pulley bolts to 16-18 ft. lbs. (22-24 Nm).
Install the front engine mount (mounting insulator).
Confirm that the draincocks are closed on the engine block and radiator. Refill the engine with coolant. Reconnect the negative battery cable. Start the engine and check for leaks.

Posted on Jul 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, My car goes into gears whilst idling without even pushing the clutch in. any ideas as to what they might have done wrong? they were fixing the engine before this as the crank shaft pulley broke.


You mean the stick just falls into gear? while engine is running and the car lurches forward? I would say the gates are wore out in the transmission, but even at that, it should not go in gear unless you have the clutch pushed in, IF it were to try to engage while car is running, the shifter would come in contact with the gear in the trans and grind because the clutch would not be engaged. Maybe somehow the linkage got bent on the transmission while they were replacing the pulley on the car or a bushing broke on the shifter linkage?

Aug 28, 2015 | 1993 Toyota Corolla

1 Answer

I have a 1993 toyota corolla wagon dx, that I can not get out of park.Does anybody know anything about this and how to fix it?Thanks


If you replaced the solenoid that locks the shifter in park, the problem could be the brake light switch on the brake pedal. The pedal sends power to the solenoid to unlock the shifter.

Dec 20, 2012 | Cars & Trucks

1 Answer

Shifter light bulb burned. need directions to replace on a 99 toyota corolla


He's asking about the (Transmission) SHIFTER light bulb IN THE CAR you ****!! Not the headlight! Can't stupid people READ!!??? Quote: "Shifter light bulb burned."

Dec 20, 2010 | 1999 Toyota Corolla

1 Answer

I have a Toyota Corolla AE 100 manual gear shift gets stuck


why my 2006 corolla car gearbox is stuck in third gear and cannot move

May 29, 2010 | 1991 Toyota Corolla

1 Answer

O/d off on console


May be on the shifter handle just under where your thumb could bump it.

Apr 14, 2010 | 1993 Toyota Corolla

1 Answer

Replace gear shifter bulb 1998 corolla


Remove the Middle/Cubby Hole/ E-brake cover (2 bolts and 2 screws) look under the gear shift control box towards the right, directly under the P,R,N,D,2,L. There will be a small wiring harness going into the box, you quarter twist the bulb housing out to replace.

Mar 13, 2010 | 1998 Toyota Corolla

1 Answer

Light in toyota corolla VE 98, automatic gear shifter is not working how to fix it?


you have to remove the screws (or bolts) inside the center console compartment. pry up the little ring around the shifter. pull up the e-brake and pull that whole assembly up. once removed there is a small 194 bulb located on the drivers side on the bottom. you should see the little black base. twist counterclockwise to remove. replace bulb and reinstall

Dec 04, 2009 | 1998 Toyota Corolla

1 Answer

Used toyota corolla 96' gear shifter light


There is a bulb under the shifter. It is probably burned out.

You need to purchase a number 194 bulb at an auto parts store. Next, you need to remove the entire center console to gain access to the socket that holds the bulb. This is fairly easy. After the console is removed, look under the shifter assembly to locate the socket.

A FixYa rating (4 blue diamonds) would be greatly appreciated for my assistance.

Please respond if you have any further questions.

Feb 15, 2009 | 1996 Toyota Corolla

1 Answer

4th gear engaged


There is a button on the side of the "shifter" knob that engages and disengages 4th gear.

Dec 20, 2008 | 1993 Volvo 940

1 Answer

Shifter light does not come on


If the instrument panel lights up, the fuses are OK. You prob just have a burned out bulb at the shifter dial. You need to remove the center console to change it;
The bulb number you need to buy is: "194".

Sep 02, 2008 | 1993 Toyota Corolla

Not finding what you are looking for?
1993 Toyota Corolla Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...