Question about 1993 Toyota Corolla

1 Answer

How to adjust headlight beam for 1993 corolla

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 404 Answers

There are two screws/adjusters on the back of the lamp, one controls it left/right, the other up/down.

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust headlights 1995 GMC


Here are directions....
  1. Park the vehicle on a level surface, with the fuel tank about 1 / 2 full and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.



0996b43f8022cced.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Location of the aiming screws on most vehicles with sealed beam headlights


0996b43f8022ccee.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Dual headlight adjustment screw locations-one side shown here (other side should be mirror image)


0996b43f8022ccef.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Example of headlight adjustment screw location for composite headlamps

  1. If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.
  2. Turn the headlights ON and mark the wall at the center of each light's low beam, then switch on the brights and mark the center of each light's high beam. A short length of masking tape which is visible from the front of the vehicle may be used. Although marking all four positions is advisable, marking one position from each light should be sufficient.



0996b43f8022ccf0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: Low-beam headlight pattern alignment


0996b43f8022ccf1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: High-beam headlight pattern alignment

  1. If neither beam on one side is working, and if another like-sized vehicle is available, park the second one in the exact spot where the vehicle was and mark the beams using the same-side light. Then switch the vehicles so the one to be aimed is back in the original spot. It must be parked no closer to or farther away from the wall than the second vehicle.
  2. Perform any necessary repairs, but make sure the vehicle is not moved, or is returned to the exact spot from which the lights were marked. Turn the headlights ON and adjust the beams to match the marks on the wall.
  3. Have the headlight adjustment checked as soon as possible by a reputable repair shop.

Jan 26, 2014 | 1993 GMC Sierra K1500

1 Answer

Low beam toyota corolla


There will be no adjustment for low beam as the headlight assy. adjusts for both beams. Adjust lights on high beam from a distance of about 3 ft(1meter) The center of the beam to be slightly below center height of the light and slightly to the left (AUS) or right (USA). Face the car to a wall at night is best.

Apr 28, 2013 | Cars & Trucks

2 Answers

My lights are not see properly if i dip my lights i can only see in a distance of 5mitres but if i beam mylights i can see a distance of 9 to 10 mitres its a toyota corolla ae91 please help me


Your headlights need aiming correctly. There are screws next to the headlight the achieve this . Park the car on level ground about 2 meters (6feet) from a solid wall and turn the lights on to high beam. You will see the centre of the beam measure the height from the floor to the center of the headlight and mark this on the wall directly in front of the vehicle. The center of the beam has to be adjusted to to this point.Don't worry about low as the beam for low is set by the bulb and is correctly positioned in relation to high at all times

Feb 07, 2013 | 1990 Toyota Corolla

1 Answer

Need to adjust low beam headlights on 2003 corolla


There is a screw located above the headlamp by the upper rad support. This adjustes the headlamp aiming position.

Oct 19, 2010 | 2003 Toyota Corolla

1 Answer

How do you adjust headlights on a 1993 chevy C1500


if you look at the light, there is an adjustment screw at the top of the light that controls the up and down motion , clockwise will raise the beam, and a screw on the side that controls the side to side motion. the best way to center your lights would be to park the vehicle 25 feet away from a verticle wall. be sure to be very square to the wall and on level ground. make a tape line vertically on the wall in very close relation to the center of the vehicle, and another tape line vertically in very close relation to the center of each headlight. now place a tape line horizontally in very close relation to the center of the headlights. start with low beam adjustment. adjust the high intensity zone to 2 inches below the horizontal line and 2 inches to the inside of the vertical line directly in front of the headlight. for high beam adjustment, adjust so that the high intensity zone is centered on the center vertical line and just below the horizontal line. hope this helps

Apr 04, 2010 | 1993 Chevrolet C1500

1 Answer

My GMC truck 1993 Sierra just had new headlights installed. But the high beams point into the trees. It seems both the high and low beam lights are in one enclosure. Can I adjust these down?


Yes you can. There is an adjustment screw at the top of each head lamp and you just turn them out or counter clockwise and the beam will come down. You may also have to adjust them side to side also. There is an adjustment screw as well.

Aug 27, 2009 | 1993 GMC Sierra K1500

2 Answers

Hi, could you please advice me how i can adjust the headlights for 92' toyota corolla? Thank you


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jul 10, 2009 | 1992 Toyota Corolla

1 Answer

1993 toyota corolla head & tail lights


did you check the bulb,relay or fuse for low beam

Jun 04, 2009 | 1996 Toyota Corolla

1 Answer

Low Beam Headlights Not Working


to troubleshoot i would suggest buying a new headlight if the new one works just buy the other one it is not uncommon for just one beam to go out hope this helps regards jim

Mar 18, 2009 | 1996 Toyota Corolla

Not finding what you are looking for?
1993 Toyota Corolla Logo

564 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...