Question about 1998 Mitsubishi Diamante

Open Question

Engine light flashing. Fault code 78 (APS Main). Vehicle does not start.

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: fault code 77 & 78 aps app on my spacewagon gdi 1999

get an diagnostics check.. it might be ur m.a.f. sensor. i had the same problem. it idled high. and wouldn't break 60 mph

Posted on Feb 12, 2009

  • 1 Answer

SOURCE: 98 mitsubishi grandis chariot fault code 78

mitsubishi grandis 1999 low fuel, it starts but cut out

Posted on Jun 19, 2010

  • 1 Answer

SOURCE: 98 MITSI PAJERO FAULT CODE 78 APS(MAIN)

78 APS (main) what does mean?

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine trouble code P2106


Faulty Accelerator Position Sensor(APS)
- Faulty APS+Brake
- Faulty APS + Vehicle speed sensor
- Faulty APS + Vehicle speed sensor + Brake
- Faulty Electronic Throttle Control(ETC) Items(TPS or ETC motor etc)
- Faulty Powertrain Control Module (PCM)

Jan 28, 2015 | 2007 Hyundai Entourage Limited Minivan

Tip

?JCB FAULT CODES LIST


P0087 (flashing code 227) shared sump low pressure fault (for pump without pressure supply)
The main fault symptoms
• Engine severe vibration.
• idling unstable
• Output Fall
• exhaust smoke
• It may be too large output
P0088 (flashing code 118) shared the tank pressure is abnormally high (first or second stage)
The main fault symptoms
• Engine severe vibration
• idle instability
• Output Fall
• channeling gas engine failure
• exhaust smoke
• It may be too large output
P0089 (flashing code 151) shared the tank pressure failure (for pump pressure supply is too large)
The main fault symptoms
• Engine severe vibration
• idle instability
• Output Fall
• channeling gas engine failure
• exhaust smoke
• It may be too large output
P0090 (flashing code 247) SCV drive system open, + B short circuit or shorted to ground
The main fault symptoms
• Depending on the open / short situations, there may be an engine stall and / or launch
Machine channeling gas.
• exhaust smoke
• Output is too large
P0107 (flashing code 71) atmospheric pressure sensor circuit input low (open or shorted to ground)
The main fault symptoms
Due to spare the equivalent altitude 2000 m (6562 ft)
• exhaust smoke at high altitude.
• insufficient output at low altitude
P0108 (flashing code 71) atmospheric pressure sensor circuit input high (+ 5V shorted)
The main fault symptoms
Due to spare the equivalent altitude 2000 m (6562 ft)
• The high altitude exhaust smoke
• lack of low altitude output
P0112 (flashing code 22) intake air temperature sensor fault (low voltage fault, earth fault, short circuit)
The main fault symptoms
• When cold starting, may exhaust white smoke.

More here http://truckmanual.weebly.com/jcb-fault-codes.html

on Dec 20, 2016 | Cars & Trucks

1 Answer

Code aps p2183


Generic OBD Error Code Details for P2183 Engine Coolant Temperature Sensor 2 Circuit Range/Performance
You could have a stuck open engine thermostat.

Oct 15, 2012 | 2006 Mitsubishi Lancer

1 Answer

Truck will be running fine, then all of a sudden it will completely shut off. After we wait a few minutes and pump the clutch and make sure it is all the way to the floor it will start, sometimes. S


You need the engine computer scanned for fault codes, i thank you have an ignition control problem like a module or distributor pickup coil issue. These parts whenthey fail should leave fault cdes so get them read.
Next, the check engine light will pause shortly followed by the second digit of the trouble code. For example if the check engine light blinks once and pauses followed by six blinks the trouble code number would be 16. If no code is present the check engine light will stay one constantly. To restart code gathering turn the ignition key to the "off" position, wait three minutes and turn the ignition key back "on" again without starting the engine. Remove the jumper wire once code gathering is complete. To clear code after the repairs have been made remove the negative battery cable for one minute and reconnect.
toyota_dianostic_connector.jpg
Toyota Diagnostic Connector
Toyota Code Definition Table
Code 11 Momentary interruption in power supply to ECU (electronic control unit or computer) up to 1991
Code 12 Engine revolution signal missing Code 13 Rpm signal to ecu missing above 1000 rpm
Code 14 Igniter signal to ecu missing
Code 16 A/T control signal missing from ecu
Code 21 Main oxygen sensor signal fault
Code 22 Water temperature sensor circuit fault
Code 23 and 24 Intake air temperature signal fault
Code 25 Air/fuel ratio LEAN
Code 26 Air/fuel ratio RICH
Code 27 Sub-oxygen sensor signal or heater circuit fault
Code 28 No. 2 oxygen sensor/heater signal fault
Code 31 and 32 Air flow meter circuit or Vacuum sensor signal fault Code 34 and 36 Turbo-charging pressure signal fault
Code 35 Altitude compensation sensor signal fault
Code 41 Throttle position circuit fault
Code 42 Vehicle speed sensor circuit
Code 43 No starter signal to the ecu
Code 51 AC signal on; DL contact off (in transmission shifter with diagnostic connector jumped)
Code 52, 53 and 55 Knock sensor fault Code 71 EGR system malfunction
Code 72 Fuel cut solenoid signal fault
Code 78 Fuel pump control signal fault
Code 81, 83, 84 and 85 TCM communication fault

Jun 28, 2012 | Cars & Trucks

2 Answers

Am driving a mitsubishi chariot grandis it just switched off engine while still driving, when i tried to restart it starts but switches itself off it doesnt run the engine. please help what could be tha...


Hello and welcome to FixYa!

This can lead to many things, most of all is because of a bad sensor. There can be a bad sensor somewhere and I strongly suggest that you have the engine scanned. During the diagnostic it will list the trouble codes and by then you'll know what part is in need of replacement.
Although in my own opinion, it can be a possible MAF (mass air flow) sensor issue. If the MAF is faulty there will be vacuum irregularities.
Hope this helps and thank you for using FixYa! Have a good one!

Apr 25, 2011 | Mitsubishi Colt Cars & Trucks

4 Answers

98 mitsubishi grandis chariot fault code 78 APS(main)


mitsubishi grandis 1999 low fuel, it starts but cut out

Jun 02, 2010 | 1984 Mitsubishi Starion

1 Answer

Fault code 77 & 78 aps app on my spacewagon gdi 1999


get an diagnostics check.. it might be ur m.a.f. sensor. i had the same problem. it idled high. and wouldn't break 60 mph

Feb 12, 2009 | Mitsubishi Colt Cars & Trucks

Not finding what you are looking for?
1998 Mitsubishi Diamante Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...