Question about 1994 Ford Aspire

1 Answer

There is no power at all when when i turn the ignition. hazards dont work nothing will turn on.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,051 Answers

Is the battery ok? the cables clean and tight?

Posted on Sep 30, 2010

Testimonial: "that was it... checked the terms and it wiggled a bit and it was like magic, it started again! they were corroded so i bought replacements."

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 67 Answers

SOURCE: hazards work turn signals dont

check your flasher the Hazards have a seperate flasher its a littl cube that looks like a relay in or near the fuse box

Posted on Apr 10, 2009

ahmed_mmm
  • 72 Answers

SOURCE: I have aproblem with my 1983 Mazda 626, when i

defective contact switch

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I tried to program a new fob for a 1999 Altima. And nothing worked





1.   Close and lock all doors with the driver’s side power lock/unlock switch.

2.   Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast, system will not enter programming mode.

3.   Insert key into the ignition cylinder and turn to the ACC position.

4.   Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press the button more than one time in the above step. If the button is pressed more than one time, the programming procedure will not be successful.

5.   If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should flash. Repeat this step for each transmitter (including any existing transmitters).

6.   Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.




Make sure you have the right fob for your car.

Nov 15, 2016 | 1999 Nissan Altima

1 Answer

I turn the key and nothing no lights on dash battery is good and fuses!!


Check for power to the ignition switch via test light or better a multimeter, could be a blown fusible link, usually housed in engine bay , or faulty ignition switch...
Work your way forward from the battery, testing power to and through all fuses, connections.

Do the headlights or hazard lights work...

Feb 03, 2016 | Cars & Trucks

1 Answer

How to fix 2001cavalier no hazards,turn signals,or brake lights check all fuses,tried new turn signal switch, tried bulbs an relays nothings working plz help


you have two fuses that suppy power to the system one has power all the time the other when you turn ignition on

Sep 09, 2014 | 2001 Chevrolet Cavalier

2 Answers

Chrysler Vision hazard light


on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

Hasards dont come on on a 2000 isuzu trooper


No need to panic-this can SEEM TO be caused by a couple of things, but it is fairly simple to determine exactly what is causing this flasher circuit condition.
First, turn on your flashers, however you have to do it, and walk around the truck to check that all bulbs are working (at least one on each corner). Turn signal and hazard flasher relays are thermal circuit interrupters and are current sensitive and will not work properly with too few or too many bulbs in the circuit. (This is usually a big problem when switching over to LED lamps, as LEDs only draw a fraction of the current that the bulbs do. This causes the relay to either not flash at all or flash very fast and triggers warning circuits on newer cars) If there is one or more bulbs out, they must be replaced.
That being said, I doubt that alone is your problem. Here is a general automotive wiring primer aimed at the turn signal, hazard, stop, and running lights on most all motor vehicles.
Hazard flashers are required by D.O.T. safety standards on all motor vehicles that may ever be used anywhere near a public road. They are also required to be able to be used without the ignition key. This means the flasher circuit for hazards is fed thru a fuse that connects straight to the battery and is energized at all times.
Turn signal circuits often share the same flasher relay as the Hazards, even though the power for them is switched through the ignition key. Power for directional blinkers connects to a fuse, then the ignition switch, then to the battery.
So, if you have to turn on the turn signals (is the key on?) to get hazards to work, that means they are not getting power direct from the battery, but can get it when the turn signals are on because they both use the same relay. This is usually the case on all vehicles; If 4-way flashers and turn signal are both on at once, the 4-ways override the turn signal and force all signal bulbs to flash. The turn signal never forces one side of the hazards to stop blinking.
So, where does that leave us? You simply have a blown fuse, my friend. The hazard lamps fuse may also power the cigarette lighter, dome light, or other "always on" accessories. This varies with make & model, but the Hazard Lps fuse is usually well marked in the fusebox. If the fuse blows again shortly after being installed, do not put in a larger one! Try one more. If it also blows immediately, there is a problem with the wiring, or a bulb could be in wrong and shorting to the socket ground. Try removing all the flasher bulbs and trying the switch(it won't flash or "tick-tock") again. If the fuse does not blow, you have found the problem. Good hunting!

Apr 15, 2013 | 2000 Isuzu Trooper

1 Answer

95 nissan d21 will not turn on/over


You have power to other items but if you have none to the ig switch usually a big red or brown wire then there is nothing going back to the starter etc.You say the red is dead. That usually comes from the big starter terminal. Try google images for a diagram if you don't have one. Alternatively if you can easily access the starter take a length of heavy wire and flash between the battery positive and starter terminal and see if it turns over. If so, you have to fault find the supply to the key.

Apr 08, 2017 | Nissan Cars & Trucks

1 Answer

Yeah my Trajet won't start,Battery seems fine plenty of power,however when I turn the ignition key there is nothing ,all the dash lights come on by half power sometimes strong sometimes they fade out,all...


Check and possibly clean all connections to the battery(bat clamps/posts)...check to be sure the ground on the block and the body are clean and well connected

Jan 20, 2011 | Hyundai XG350 Cars & Trucks

1 Answer

Hazards work turn signals dont


check your flasher the Hazards have a seperate flasher its a littl cube that looks like a relay in or near the fuse box

Apr 07, 2009 | 1987 Pontiac Firebird

1 Answer

1997 Jetta will not start with abrand new battery!


Dont have a clue about the hazards but the connections on the starter could be bad

Nov 03, 2008 | 1997 Volkswagen Jetta

Not finding what you are looking for?
1994 Ford Aspire Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...