Question about 1991 Toyota Camry

1 Answer

I need to change my struts and I dont know if I need any special tools or presses

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

You are going to need a compressor for removing the coil springs from the old struts and putting them on the new ones. You are going to need top strut mounts as yours are old. You are going to need some big wrenches with extenders to get the bottom bolts loose. You are going to need an alignment rack as the car will have to be aligned when put back together. You will need someone to operate the alignment rack. Try and track down some "quick struts" for your car these already have the new coil spring and mount installed. Save time and money. Look on ebay.

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to comprese strut on a2000 Buick lesaber


you can take the strut cartridge from the top,without disassembling spring and knuckle,there are there are 3 15 mm bolt on strut 9need to be torqued to 24 LB FEET) then you need special tool to take the strut mount and cover out ,(it is 24 mm bolt that you have to put #50 torx bit in the center to keep strut rod from tuning NEED 59 LB FEET of torque)

,then you take the bumper,mount and the boot out to put the special tool to keep the strut cartridge in place or it will shift side way ,and you have to tow the car to shop to get it done!!!,after that you use special tool to loosen the cartridge cover (NEED 82 LB FEET WHEN PUT BACK)take the strut out,suck the oil with the hand pump out,and put 50CC back,as it needed to help cool down the strut,( when you put new strut in the oil level should cover half of the strut no more) ,and reverse the process after that,

this is the tool you need,
Alltrade 648609 Kit 19 General Motors Body Strut Remover Tool Set

Oct 24, 2014 | 2000 Buick LeSabre

1 Answer

Relacing struts on 03 dodge stratus sxt coupe 2.4L


dont know if your changing front or rear but i suggest buying the struts as an assembly. this way you get everything new. rock auto just got a new listing for these. you dont need any special tools to install them. i drive an 03 r/t myself.

Jul 31, 2014 | 2003 Dodge Stratus

2 Answers

My olsdmobile aroua needs shocks. about what is the cost on shocks installed? Jim Fields


Your car has struts. The strut cartridges are about $80.00/ea and require some special tools. You have to take the whole assembly out of the vehicle and then using a special set of tools, compress the spring that is attached to the strut. Once the front struts have been replaced an alignment is needed. depending on labor rates in your area, figure about 2 hrs. for the strut change and then what ever an alignment costs. I think about $400.00 is in the ballpark.

Jan 31, 2011 | 2001 Oldsmobile Aurora

1 Answer

How to chnge control arm bushing on 1994 dodge intrepid


Here are the instruction on how to replace your control arm bushing. please not that there is a special tool needed that you will need to get from you auto parts retailer. you can usually rent these tools.
    1. Turn the control arm over in the arbor press, then position the arm so that it is supported by the receiver tool MB-990799 as shown.
  1. Position the new bushing into the control arm so it is square with the bushing hole. Position the installer tool MB-6644-1 or equivalent on top of the bushing, with the bushing setting in the recessed area of the installer tool. Press the bushing into the control arm.
  2. Press the control arm bushing into the control arm until the installer tool squarely bottoms against the surface of the control arm. When the installer tool squarely bottoms on the control arm, the bushing is installed in the arm in the correct position.
  3. Install the tension strut into the strut bushing in the control arm. Position the tension strut in the control arm with the word FRONT stamped in the tension strut positioned away from the control arm. With an open end wrench on the flat of the tension strut to stop the tension strut from turning. Tighten the NEW tension strut-to-control arm retaining nut to 110 ft. lbs. (150 Nm).
  4. Install the lower control arm and tension strut back onto the vehicle. Refer to the Lower Control Arm procedure earlier in this section.


Control Arm-to-Tension Strut Bushing
To replace the control arm tension strut bushing, the control arm and tension strut assembly must be removed. The removal of the bushing requires the use of an arbor press.
  1. Thoroughly lubricate the replacement tension strut bushing, control arm and installer tool 6644-3 or equivalent with a silicone lubricant.
  2. By hand, install the tension strut bushing into the large end of the installer tool. Press the bushing into the installer tool as far as it will go by hand.
  3. Position the control arm in the arbor press so that the tension strut hole in the control arm is centered on the receiver tool MB-990799 or equivalent. Position the installer tool with the previously installed bushing, inside of the tension strut bushing hole in the control arm. Position the installer tool on top of the tension strut bushing. Using the arbor press, press the tension strut bushing into the control arm. As the bushing is being pressed into the arm, a pop will be heard. When the pop is heard, the installer tool will slightly move up off the control arm. At this time remove the control arm assembly from the press and pull the tool MB-6644-3 off of the tension strut bushing in the control arm.


Jun 19, 2010 | 1994 Dodge Intrepid

2 Answers

Does my 1993 6 cylinder 3.0 Plymouth Voyager have shocks or struts in the front?


Hello tunamae: My name is Roger and I will help. Your 1993 Voyager has struts on the front of the vehicle. In order to change them you will need special strut tool in order to change the strut springs form the old struts to the new ones. Should you need further help please just ask.Please rate the answer you received as this way I know it was helpful. Thank You for using Fix Ya, Roger

Mar 18, 2010 | 1993 Plymouth Voyager

1 Answer

Trying to change front struts on 2002 chevrolet trailblazer,how do they slide off.


i did the front struts on my 03 envoy, same thing as trailblazer, it is a very difficult thing to do and you need a few special tools, if your not the most mechanicaly inclined dont try it

Nov 24, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Shocks


Struts have big springs around them and they need to be compressed to change the strut. These compressed spring store a large amount of energy and can be very dangerous when handled improperly. This requires special tools and skills. Also after changing struts a wheel alignment is necessary. Unless you are a very experienced do it yourselfer changing struts is probably not something you should try. Take it to a shop.

Oct 20, 2009 | 2005 Honda Civic

2 Answers

Replacement of rear struts on a 2004 KIA Optima


CHANGING STRUTS REQUIRES A SPECIAL TOOL YOU RENT AT ANY PARTS STORE. THEY ARE NOT BAD FOR SOMEONE WHO KNOWS HOW TO FOLLOW INSTRUCTIONS. THE TOOL HAS INSTRUCTIONS AS LONG AS YOU FOLLOW THEM STEP BY STEP, YOU'LL BE FINE. SHOPS MAKE WAY TOO MUCH MONEY ON THAT STUFF. THEY GET A 30-40 PERCENT DISCOUNT ON THE PARTS; THEY CHARGE YOU 15 PERCENT MORE THAN WHAT YOU WOULD PAY; AND THEY CHARGE TOO MUCH FOR LABOR. GET A BOOK NEXT TIME AND RENT THE TOOL. YOU'D BE SURPRISED HOW EASY THEY ARE.

Jul 27, 2009 | 2004 Kia Optima

1 Answer

Changing air bellows on a oldsmobile 98 95 Rear,


Unless your dead broke, get the dealer or trusted mechanic to do the job. The perils of dealing with loaded springs, etc. just isn't worth the personal risk IMHO. Not to mention that the parts will be hard enough to get and the mechanic will order all the little parts, gaskets, etc. etc. that are needed without having to make multiple trips back to NAPA, if you know what I mean. ;-)

May 06, 2009 | 1992 Oldsmobile Ninety Eight Regency

1 Answer

Procedures for replacing front shocks/struts on 1985 bmw 325e


are you changing the strut cartridge or the whole spring unit? if you are installing the whole unit, spring and all you will need no special tools, if not you will need a spring compressor

Apr 06, 2009 | BMW 325 Cars & Trucks

Not finding what you are looking for?
1991 Toyota Camry Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...