Question about Ford F-350

2 Answers

I need the schematic for a rear differential on a 1991 Ford f350 the drive shaft is very loose where it goes into the differential and hubby needs to see what he has to replace 1FTHF36M6MNA41660 is the serial number to tell you which differential THANKS for any reply

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,796 Answers

HI!!
Here are some diagrams for the 3 different drive shaft axles that came with this truck. Click on the following link for step by step instructions and pictures on removal and installation of the drive shaft. http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f8038ead8
Good Luck!! Don't forget to rate this post!!
SLIP YOKE DRIVE SHAFT I need the schematic for - 7e10b35.gif
SLIP YOKE TWO-PIECE DRIVE SHAFT 7dbeb20.gif
FIXED YOKE TWO-PIECE DRIVE SHAFT c9f7f4c.gif

Posted on Sep 30, 2010

Testimonial: "Wonderful feedback for this poster! Gave us exactly what we needed and more!!! And because we are such newbys, he really tried hard to get it thru!"

  • 8 more comments 
  • chasincows Sep 30, 2010

    You are real close but we need the diagram where the drive shaft goes into the rear differential ...it is a 410 gear ratio Van **** if that helps. Thank you so much for posting the pictures as that is also what we need. Is it possible to get pics of the rear differential??

    Thanks Again DEDE

  • Rene J Solis Sep 30, 2010

    If it is a Van, it is an E350. No problem give me a few to find your info

  • chasincows Sep 30, 2010

    NOT a Van don't know why they wont let you see VANDYKE type of rear differential on F350 it is a pick up truck!!! HA

  • chasincows Sep 30, 2010

    Tryingagain V-A-N D-Y-K-E is type or manufacturer of rear end THANKS AGAIN

  • Rene J Solis Sep 30, 2010

    Click on this link, once there, scroll down or select from the left menu where it says Select Chapter the specific section you need. In case you don't find what you need, post a comment and I'll help you find it. Keep me posted!!

  • Rene J Solis Sep 30, 2010
  • chasincows Sep 30, 2010

    I tried but it keeps sending me to membership place cause I am not a member???

  • Rene J Solis Sep 30, 2010

    that usually happens when you cut and paste the link, if you double click, it should take you to the site.

  • chasincows Sep 30, 2010

    I did click on it so now I am a member and trying this way....Gonna get it come H--L or High Water....and today in VA the high water is a problem Thanks I think I can get into Autozone now will keep trying!!
    You are very helpful to a newby and should have many stars beside your name (ebay referance!! ) HA!

  • Rene J Solis Sep 30, 2010

    Thank you, let me now if you need assistance later on. Thank you for using FixYa. Rate this post!!

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 829 Answers

If he does not know what parts are in there then he is not qualified to replace then. Diffs are simple as far as numbers of parts go. It will take special tools and knowledge to get it set up properly. this not an unbolt and bolt up new parts deal.

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 1963 ford 2000 tractor 4 speed trans that the rear differential gears are no good need to know if rear differential out of a selectospeed would enterchange


If your talking one speed to a two speed differential, no they won't be compatible. Most likely will have to replace the rear end complete and modify the drive shaft.

Jun 28, 2016 | Ford Cars & Trucks

1 Answer

No power going to rear wheels


is your car a rear wheel drive vehicle? if yes, check your drive shaft, it might already be disconnected to the transmission or differential. Transmission is the one attached directly to your engine, differential is attached to the rear wheels.

Aug 05, 2011 | 1991 Subaru Legacy

1 Answer

1998 ford explorer 2 wheel drive rear wheel bearing replacement


what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) swn~us~en~file=st1514a.gif~gen~ref.gif Axle Seal Replacer
T83T-1175-A swn~us~en~file=st1283a.gif~gen~ref.gif Axle Wheel Bearing Puller
T83T-1225-A swn~us~en~file=st1322a.gif~gen~ref.gif Axle Wheel Bearing Replacer
T83T-1225-B swn~us~en~file=st1326a.gif~gen~ref.gif Driver Handle
T80T-4000-W swn~us~en~file=st1185a.gif~gen~ref.gif Impact Slide Hammer
T50T-100-A
Removal
  1. Remove the axle shaft; refer to Axle Shaft in this section.
Axle Shaft Removal
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
    Loosen the lug nuts (1012).
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
  1. Raise and support the vehicle.
  1. Remove the wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the wheel and tire assembly.
  1. Remove the axle housing cover (4033).
    1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
    1. Remove the axle housing cover bolts.
    1. Remove the axle housing cover.
  1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Remove the U-washers (4N237).
    1. Push the axle shafts inboard.
    1. Remove the U-washers.
  1. Reinstall the differential pinion shaft.
    1. Install the differential pinion shaft.
    1. Install the differential pinion shaft lock bolt finger-tight.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal (1177).
    Remove the two axle shafts.
Installation
  1. Lubricate the lip of the inner wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inner wheel bearing oil seal.
    Install the two axle shafts.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
    Install the U-washers.
    1. Position the two U-washers on the button end of the axle shafts.
    1. Pull the axle shafts outward.
  1. Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
    1. Install the differential pinion shaft lock bolt.
  1. Install the rear disc brake rotors; refer to Section 206-04 .
  1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.
  1. swn~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
    Clean the wheel hub and mounting surfaces.
  1. Install the tire and wheel assembly.
    1. Position the tire and wheel assembly.
    1. Install the lug nuts and lower the vehicle.
    1. Tighten the lug nuts.
    1. Install the center cap.


  1. swn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
    NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
    Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.
Installation
  1. Lubricate the new rear wheel bearing.
    1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.
  1. Lubricate the lip of the new axle shaft oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.
  1. Install the axle shaft; refer to Axle Shaft in this section.

May 18, 2011 | Ford Explorer Cars & Trucks

2 Answers

I need to converd my 2wd 1999 ford F350 into a


Yes, it can be done, but it will be highly expensive as it will be necessary to replace the gearbox and the front axle and to add a transfer box , a cardan shaft and all the commands. In the end it will be cheaper to just sell your 2WD and buy a same year 4WD.

Jun 22, 2010 | 1999 Ford F350 Regular Cab

1 Answer

What type of fluid is used in my diesel 2001 F350 front and rear differencial?


Front differential is: 75W-90

Rear Differential is a little different...what type of differential...limited slip or standard differential? Dana 135?


Axles subject to frequent trailer towing in hot or
hilly conditions may use Synthetic 75W-140 GL-5

Jun 10, 2010 | 2001 Ford F350 Super Duty SuperCab

1 Answer

I am trying to remove the drive shaft from the rear differential.


place a pry bar between the yoke and the ujoint. push to the front of the vehicle. make sure that if it has a two piece shaft, the middle support is loose

Sep 19, 2009 | 1991 Chevrolet C2500

2 Answers

Rear axle leaking


Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.

Jun 23, 2009 | 2004 Ford F150

1 Answer

1985 M Benz Sd differential s half shafts


first remove the differential half shafts and drive shaft, remove rear cap, loose the bolts on each end bearing,remove the differential assy. then replace bearings

Apr 12, 2009 | 1985 Mercedes-Benz 300

1 Answer

Differential fluid in a 2003 ford F350


It really depends on the rear axle you have in your truck because there are actually 3 different ones but all of them you remove the rear cover,then clean it and add a bead of silicone rubber to the cover and reinstall and refill.Here is where the difference comes in as to how fluid much to add. The fill plugs are in different places, one is at the front near where drive shaft hooks up, this one you fill to within 1/4 of the plug openning. The other one is in the rear cover and you fill it to bottom of the hole.

Mar 12, 2009 | 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

Replace left rear axle seal 1999 ford explorer


Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the differential housing cover (4033).
    1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
    1. Remove the bolts.
    1. Remove the differential housing cover.
Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  2. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the U-washer groove.
  3. Remove the U-washer (4N237).
  4. Push the axle shaft inboard.
  5. Remove the U-washer.
Reinstall the differential pinion shaft.
  1. Install the differential pinion shaft.
  2. Install the differential pinion shaft lock bolt finger-tight.
  3. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal (1177).
    Remove the axle shaft.
-----------------------------------------------------------------------------------------------------------------
Seal Removal
  1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
    NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.
6c7eb46.gif Installation
  1. Lubricate the new rear wheel bearing.
    • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
    • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Using the special tools, install the rear wheel bearing.

ece7d89.gif
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the wheel bearing oil seal.
c21e27d.gif
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

Feb 22, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,065 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...