Question about 2004 Mitsubishi Endeavor

Open Question

How do you reset low pressure light in my endeavour. I had tire repaired and low light appears on dash

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: LOW TIRE PRESSURE WARNING LIGHT

Turn ignition to run position,go to fuse panel right hand of vehicle,push and hold reset button for 5 seconds,low pressure light will flash 3 times,start car it should turn off the low pressure light.

Posted on Jan 29, 2009

Ad
DAD5bbbbg
  • 111 Answers

SOURCE: low tire pressure light is on all tire pressure is

Turn off the radio and turn the key to the on postion. push the bottom knob ( to turn the station). Hold it in intell the info comes on. in the window it will show all the things you can reset. using the arrows to the right of the knob find tire reset the push on the station knob. this will reset it. then go back to the arrows and find end. push on the knob one more time and you will be done.( you have to make sure the radio is off). I hope this helps.

Posted on Feb 28, 2009

  • 29 Answers

SOURCE: low tire pressure idiot light

Your nissan also has a tire monitor on your spare tire if your spare has low pressure and the other 4 tires have correct pressure the light will stay on . after you ajust the spare also the light should go away.

Posted on Mar 24, 2009

  • 1 Answer

SOURCE: Lexus sc430 tire pressure monitor

there is a reset button for the tpms either just above the accerlator or to the right of the glove box. press it and tah dah....you should be good to go.

Posted on May 24, 2009

Testimonial: "Knowledgeable expert...found the button (but unfortunately did not fix problem--maybe shop messed up a sensor in the tire)"

  • 1 Answer

SOURCE: How do you reset a low tire pressure warning on a 2008 Jetta?

Reset the tire pressure warning, same as you would any service issue. Insert key in ignition, hold wrench button and min button, then start engine.

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I reset the low tire pressure light after all tires have been filled


The light goes out automatically once all tires are at the correct pressure. The proper pressure is usually labeled on the driver's door jamb.

Aug 08, 2017 | Cars & Trucks

2 Answers

Reset tire pressure light on dash 2014 ford focus


use this link.
http://enginepartsdiagram.com/2007-2016-ford-focus-tire-pressure-tpms-sensor-light-reset/

Dec 11, 2016 | Ford Cars & Trucks

1 Answer

Why cant I get low tire pressure light to stay off? have changed sensors, tires, and put air in and let it out. Nothing works!


Hello, some vehicles require to be manually reset. Some reset buttons are in the fuse box and some under dash.

Feb 06, 2015 | Cars & Trucks

3 Answers

My low tire light came on so I went and had air and all the tires checked but now I don't know how to turn the light off. I have had the car since 2000 and it has 50,000 miles on it but could never figure...


Hello Mattingly.

Here is some information for you regarding your problem.

The Tire Inflation Monitor (TIM) system alerts the driver when the pressure changes in one of the tires. The system only detects a low pressure condition while the vehicle is being driven. Once a low tire pressure condition is detected, the system informs the driver that a low tire pressure condition exist's, whenever the ignition is ON.
The LOW TIRE message appears on the Instrument panel if the tire pressure in one tire becomes at least 82 kPa (12 psi) lower or higher than the other three tires. The message does not appear if more than one tire is low or high, or if the system is not calibrated properly. The system does not inform the driver which tire is low. To clear this message, set the tire pressures in all four tires to the proper pressures and perform the system reset procedure. Refer to Tire Inflation Monitor Reset Procedure for service procedure.
The Tire Inflation Monitor software requires approximately one half hour of straight line driving to complete the TIM autolearn. There are several speed ranges that the EBCM needs to learn the tire inflation configuration in order to have the full capability of detecting a low tire condition. The speed detection ranges are the following:

  • 24-64 km/h (15-40 mph)
  • 64-113 km/h (40-70 mph)
  • 113-145 km/h (70-90 mph)
Each speed range has 2 modes of low tire detection.

  • Monitor Mode 1
  • Monitor Mode 2 The EBCM learns the tire inflation configuration for each speed range independently. In Monitor Mode 1, the EBCM has only partially learned the tire inflation configuration for the speed range and has limited detection capability for a low tire condition. In Monitor Mode 2, the EBCM has fully learned the tire inflation configuration for the speed range and has full detection capability for a low tire condition. If the EBCM is not in Monitor Mode 1 or Monitor Mode 2, a low tire condition cannot be detected because the EBCM has not learned the tire inflation configuration of the vehicle.

To reset (calibrate) the system:
Turn the ignition switch to RUN. Then press and hold the RESET button for about five seconds. The red RESET button is located inside the instrument panel fuse block on the right side of the dash.. The LOW TIRE light will come on and flash three times and then it will turn off.
The system completes the calibration process during driving.
The system normally takes 15 to 20 minutes of driving in each of three speed ranges to "learn" tire pressures. The speed rages are 15 to 40 mph (25 to 65 km/h), 40 to 65 mph (65 to 105 km/h) and above 65 mph (105 km/h).

There you are, this should fix you up.
Keep in mind this system uses wheel speed sensors to calculate. If one of your sensors isn't working your low tire light will remain on.

Thank you for using FixYa.

KL

Jan 20, 2011 | 2000 Buick Century

1 Answer

Have a yellow light on. looks like exclamation point inside u shape. Dodge ram 1500 4door 5.7 litre. thx.


That light indicates you may have a low tire, check your tire pressures to make sure they are all the same and at the recomended pressure then read your owners manual to tell you how to reset the light. Usually the button on your dash to switch the odometer to the different fuctions will have an option for "tire relearn" or "tire reset" push and hold the button when this message appears and your problem should be fixed. (unless you have a leaky tire).

Nov 30, 2009 | 2008 Dodge Ram Pickup 1500

1 Answer

Changed right front tire now reads zero on dash light is on


Your tire pressure monitor needs to be reset whenever you change or rotate your tires...

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 24, 2009 | 2008 Chevrolet Tahoe

2 Answers

Low tire light came on - tire pressure ok


Because of changing outside temps this happens, just hold reset button on left side of dash until it reads tire pressure 100% again, just make sure your pressure is right before you do it. this is the same for oil changes and the like.

Apr 26, 2009 | 2001 Buick LeSabre

2 Answers

2004 Lexus Ls 430 Low tire


My 2004 Lexus LS 430 has had the light come on several times, even after changing all four tires. There are no tire pressure sensors on my four tires. I was told the car computes tire rotations and since a low pressure tire takes more rotations than a fully inflated tire, the computer puts up a message on the dash.
To reset/turn off the message, put the emergency brake on, start the car and reach below the dash to the right side of your steering column until you feel two buttons in a depressed area under the dash. One button turns on /off your smart key and the other will turn off your tire low pressure message. Depress and hold until the message on your dash goes out and you are good to go. I know this works, I just reset mine a few minutes ago.

Mar 18, 2009 | 2005 Lexus Ls 430

2 Answers

LOW TIRE PRESSURE WARNING LIGHT


Turn ignition to run position,go to fuse panel right hand of vehicle,push and hold reset button for 5 seconds,low pressure light will flash 3 times,start car it should turn off the low pressure light.

Jan 05, 2009 | 2000 Buick Century

1 Answer

07' Toyota 4runner dash light


That icon is the low tire pressure light.
What you need to do is inflate your SPARE tire to the proper specs. The system check all 5 tires.

Dec 22, 2008 | 2007 Toyota 4Runner

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...