Question about 1997 Isuzu Rodeo

1 Answer

Changing the timing belt on a 97' rodeo. i cant get the crankshaft pulley bolt off! is there special tool or a reverse thread on it or am i just too weak to take it off?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 978 Answers

Just real hard to get offf try jam flywheel and use longer bar

Posted on Sep 30, 2010

Testimonial: "do you kno if the threading is reverse thread on it or is it loosen to the left?"

  • richochet Sep 30, 2010

    not left look up 4x4wires isuzu forumsinfo there on how to do it goodluck

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the crankshaft dumper pully?


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

Jan 27, 2016 | 2006 Land Rover Range Rover Sport

Tip

2004 Pilot timing belt replacement



(for the 105,000 mile timing belt service)

Part List :
-Timing belt: 14400-P8A-A02
-Adjuster automatic (hydraulic tensioner): 14520-P8E-A01
-Adjuster - timing belt: 14510-PGE-A01
-Idler pulley - timing belt: 14550-P8A-A01 (OR) 14550-PGE-A01 (there are 2 numbers listed)
-Alternator/Compressor belt: 38920-P8F-A02
-Power steering belt: 56992-P8A-A01
-O-RING (8.8X1.9): 91302-GE0-000
-Fender trip clips (X7): 91501-S04-003

Special Tools Needed:
Honda Crankshaft Pulley Removal Tool
3/4" breaker bar

Procedure:
-Remove tire and place the Pilot on a jack stand.

-Remove the clips holding the fender liner and lower splash shield in place (x7) and fold them out of the way.

-Make sure the #1 piston is on top dead center using the marks on the crank pulley and lower timing belt cover (19mm in the crank pulley).

-Remove the Alternator-Compressor belt (14mm boxend) & Power Steering belt. (2-12mm and 1-12mm tensioner bolt)

-Loosen the crank pulley. If you have an impact wrench or a long breaker bar it makes it easier to remove the bolt. You will also need a special tool crankshaft pulley holder (50mm) (19mm and special tool).

-Remove the side engine mount bracket (5-14mm bolts).

-Remove the crankshaft pulley.

-Remove the oil dipstick & tube (10mm).

-Remove the front & rear 'upper covers' of the timing belt housing, moving the wire harness out of the way first (5-10mm bolts for each cover).

-Remove the lower cover (7-10mm bolts).

-Remove the engine mount bracket that is bolted to the block (3-14mm bolts).

-Remove the hydraulic tensioner (2-10mm bolts).

-Remove the tensioner pulley (you will reuse the inner sleave) (14mm bolt).

-Remove the idler pulley bolt (14mm bolt with thread locker on it) (I used Loctite 242 during the reinstall because I had it on the shelf).

-Remove the timing belt.

-Before installing a new timing belt, make sure the pulleys, belt guide plate, upper & lower covers are clean and check to see if the crank and cams have rotated (mine did not move).

-The install is the reverse order of removal (make sure you torque everything correctly!)

-The removal of the lock pin in the hydraulic tensioner gave me a little trouble so I used pliers.

-Once the crank pulley is back on, check the lower timing mark (and the cam marks) before the top covers are installed.

on Oct 13, 2014 | 2004 Honda Pilot

1 Answer

Do have to take off crank shafts pulley off to replace water pump on 97 Isuzu rodeo


wow the rare post that tells the job, waterpump off. bravo !
which engine? nobody ever posts, what engine they have,
you can log in and read it your self, on any car and engine
here
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

or ill guess engine,
so i guess
2.2L (chapter engine cooling, pump off)

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Radiator hose
    • Accessory drive belt
    • Front cover
    • Timing belt. Refer to the Timing Belt procedure.
    • Water pump
3.2/3.5L
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose
    • Timing belt. Refer to the Timing Belt procedure.
    • Idler pulley
    • Water pump
now the timing belt.

2.2L
  1. Disconnect the negative battery cable.
  2. Disconnect PCV hose from cylinder head cover.
  3. Remove the air intake duct.
  4. Remove the left side ground cable from cylinder head cover and disconnect ground cable connector on the left side wheel arch. Remove right side ground cable from generator stay and disconnect ground cable connector on the right side wheel arch.
  5. Disconnect the 3 (black, green and blue colors) engine wire harness connectors from chassis harness of left rear side of compartment.
  6. Disconnect the cooling fan wire harness connector from cooling fan on left side top of fan shroud.
  7. Use a wrench to rotate the drive belt tensioner as shown to remove drive belt.
  8. Remove PCV hose from cylinder block.
  9. Remove intake duct stay from cylinder head.
  10. Remove two bolts for remove ignition cable cover from cylinder head cover.
  11. Disconnect ignition cable from ignition plug.
  12. Disconnect camshaft position sensor harness and crankshaft angle sensor harness from behind generator.
  13. Remove the 4 bolts, then remove the crankshaft pulley.
  14. Remove timing belt front cover.
  15. Loosen the timing belt rear cover bolts as shown in the accompanying figure, then remove the camshaft angle sensor.
  16. end cover off. (belt)
  17. Before servicing the vehicle, refer to the Precautions Section.
  18. Disconnect the negative battery cable.
  19. Using a box-end wrench on the drive belt adjuster, turn the adjuster clockwise and remove the drive belt.
  20. From the left rear of the engine compartment, disconnect the 3 electrical connectors from the chassis harness.
  21. Remove the crankshaft pulley-to-crankshaft bolts and remove the pulley.
  22. From the front of the engine, remove the nut and the engine harness cover.
  23. Remove the timing belt cover.
  24. Rotate the crankshaft to position the timing marks at Top Dead Center (TDC) of the No. 1 cylinder's compression stroke.


  25. Remove the timing belt tensioner adjusting bolt and the tensioner from the engine.
  26. Remove the timing belt.
bingo the belts off, pump is exposed.
now the 3.2. im going to skip the v6
but there is one step that varies, per your question , that pulley
Use tool No. J-8614-01, or a suitable pulley holding tool to remove the crankshaft pulley center bolt. Remove the crankshaft pulley.

righty tighty-lefty loosey, or RHT, right hand threads.

on the 3.2/3.5L v6 the center bolts comes off.
and this

Install the crankshaft pulley and tighten the pulley bolt to 123 ft. lbs. (167 Nm).

if car is M/T we use 5th gear, to remove crank bolts
if car is A/T this is a pain, thus the tool above.
how to lock any A/T crank to achieve this is tricky.

show a nice list of ways, some work others dont.
depends on exact engine in question, not stated once.
fly wheel lock.
DIY tool on front bolts.


i usually just make my own tool, with angle iron
some use a chain wrench, (making a nice ugly mess)
Install the crankshaft pulley and tighten the pulley bolt to 123 ft. lbs.


so post back with engine size and trans type. so we can really help
above is wild guessing and to show tip of ice berg, timing belt issues, ever done one before on this engine? T belt??????
the v6 looks like this....on more wild guess.

25401255-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg

Feb 05, 2015 | 1997 Isuzu Rodeo

1 Answer

Installing a timing belt


Timing Belt and Sprockets REMOVAL & INSTALLATION Fig. 1: If you plan on reusing the timing belt, make sure you note the direction of the rotation before removal 91053p69.jpg Fig. 2: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts 91053p10.jpg Fig. 3: Camshaft alignment using the special service tool 91053g61.gif Fig. 4: Insert the crankshaft damper bolt to turn the crankshaft and . . . 91053p64.jpg Fig. 5: . . . align the camshafts and the . . . 91053g64.gif Fig. 6: . . . crankshaft before removing the old belt 91053p66.jpg Fig. 7: Loosen the timing belt tensioner pulley bolt, slide the tensioner back and . . . 91053p67.jpg Fig. 8: . . . tighten the bolt to the farthest right hand side as possible to hold the release the tensioner pulley so that the belt can be removed 91053p68.jpg Fig. 9: . . . remove the belt starting from around the camshaft pulleys 91053p01.jpg Fig. 10: Installation of the tensioner spring and retaining bolt 91053g62.gif For information on timing belt recommended replacement interval, refer to Section 1. CAUTION
The 2.0L engine is an interference motor. Extending the replacement interval could lead to the belt breaking and severe and costly engine damage. Care must be taken if rotating the crankshaft or camshafts with the belt off, if resistance is felt, do not force them to turn.
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers as outlined in this Section.
  3. Remove the valve cover.
  4. Place Camshaft Alignment Timing Tool T94P-6256-CH or equivalent, into the slots of both camshafts at the rear of the cylinder head to lock the camshafts into position. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  5. Loosen the camshaft timing belt tensioner pulley retaining bolt and move the tensioner pulley to relieve the tension on the timing belt.
  6. Temporarily tighten the tensioner in this position. NOTE: If the timing belt is to be reused, mark the belt for the direction of rotation before removing to prevent premature wear or failure.
  7. Remove the timing belt.
  8. If required, remove the sprockets as follows:
    1. Hold the camshaft with an appropriate camshaft sprocket holding tool.
    2. Loosen and remove the camshaft sprocket retaining bolt.
    3. Remove the sprocket from the camshaft.
    4. Repeat the procedure for the 2nd camshaft sprocket.
    5. Remove the crankshaft sprocket.
  9. Slide the crankshaft sprocket onto the crankshaft aligning the key-way.
  10. Align the camshafts using the Camshaft Alignment Timing Tool T94P-6256-CH. NOTE: If the special tool is unavailable, a suitable length and width straight edge can be used to align the camshafts.
  11. Reinstall the sprockets onto the camshafts and loosely install the camshaft retaining bolts.
  12. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  13. Loosely install the crankshaft pulley to verify that the engine is at TDC. Realign the marks if they have moved.
  14. Verify that the camshafts are aligned. NOTE: It is recommended to purchase a tensioner spring and retaining bolt through the dealer parts to apply the proper tension for used or new belt installations. The spring is bolted to the tensioner assembly and becomes a part of the engine. Ignore this notice if the tensioner spring is already installed.
  15. Reinstall the retaining bolt (W700001-S309) into the hole provided in the cylinder block and place the tensioner spring (6L277) between the bolt and the camshaft timing belt tensioner pulley.
  16. Tighten the retainer bolt to 71–97 inch lbs. (8–11 Nm) .
  17. Remove the crankshaft pulley and install the timing belt onto the crankshaft sprocket, then onto the camshaft sprockets working in a counterclockwise direction.
  18. Tighten the camshaft sprocket retaining bolts to 47–53 ft. lbs. (64–72 Nm) .
  19. Be sure that the span of the camshaft timing belt between the crankshaft sprocket and the exhaust camshaft sprocket is not loose.
  20. Be sure that the camshaft timing belt is securely aligned on all sprockets.
  21. Reinstall the lower timing belt cover and tighten the retaining bolts to 53–71 inch lbs. (6–8 Nm) .
  22. Apply silicone sealer to the key-way of the crankshaft pulley and install. Tighten the retaining bolt to 81–89 ft. lbs. (110–120 Nm) .
  23. Inspect the timing mark on the crankshaft pulley to verify that the engine is still at TDC.
  24. Loosen the camshaft timing belt tensioner pulley retaining bolt and allow the tensioner spring attached to the pulley to draw the tensioner pulley against the camshaft timing belt.
  25. Remove the camshaft alignment timing tool from the camshafts at the rear of the engine.
  26. Turn the crankshaft two revolutions in a clockwise direction.
  27. Tighten the camshaft timing belt tensioner pulley retaining bolt to 26–30 ft. lbs. (35–40 Nm) .
  28. Recheck that the crankshaft timing mark is at TDC for the No. 1 piston, and that both camshafts are in alignment using the camshaft alignment timing tool. NOTE: A slight adjustment of the camshafts to allow the insertion of the camshaft alignment timing tool is permissible as long as the crankshaft stays at the TDC location.
  29. An appropriate camshaft sprocket holding tool can be used to move the camshaft sprocket (s) if a slight adjustment is required.
  30. If a camshaft is not properly aligned, perform the following procedure:
    1. Loosen the retaining bolt securing the sprocket to the camshaft while holding the camshaft sprocket from turning with the sprocket holding tool.
    2. Turn the camshaft until the camshaft alignment timing tool can be installed.
    3. Verify that the crankshaft timing mark is at TDC for the No. 1 cylinder.
    4. While holding the camshaft sprocket with the camshaft sprocket holding tool, tighten the retaining bolt to 47–53 ft. lbs. (64–72 Nm) .
    5. Remove the tool and rotate the crankshaft two revolutions (clockwise) .
    6. Verify that the camshafts are aligned and that the crankshaft is at TDC for the No. 1 cylinder.
  31. Install the valve cover.
  32. Install the timing belt covers.
  33. Connect the negative battery cable. prev.gif next.gif

Aug 17, 2010 | 2000 Mercury Mystique

1 Answer

Would like information on timing belt settings on a 1993 Isuzu Rodeo 4X4 3.2 We have already bought the book. It seems that the setting still are not what this particular motor/engine needs are there other...


look for timing marks????
Align groove of crankshaft timing pulley with mark on oil pump.
Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate. (i can email pic if needed)
When timing marks are aligned, no pistons will be on T.D.C.
install timing belt. Align the dotted alignment mark on the timing belt with the mark on the crankshaft gear.
For correct belt installation, the letters the belt must be able to be read as viewed from the front of the vehicle. It is recommended for easy installation that the belt be secured with double clips after it is installed to each pulley. Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Align the alignment mark (white line) on the timing belt with the alignment mark on the RH bank camshaft timing pulley (on the left side as viewed from the front of the vehicle Secure the belt with a double clip.
Turn the crankshaft counterclockwise to remove the belt slack between the crankshaft timing pulley and the RH bank camshaft timing pulley.
Install the belt on the water pump pulley. Remove double clips from pulleys. Turn the crankshaft pulley clockwise by two turns. Measure the rod protrusion to ensure it is within the standard. Standard 4-6 mm (0.16-0.24 in)


13) If out of standard, remove pusher, loosen adjusting bolt, and readjust. (Repeat from step 11). Tighten adjusting bolt to the specified torque. Torque 42 N-m (31 lb-ft)


  1. Pusher
    • Tighten bolt to the specified torque.
Torque 19 N-m (19 lb-ft)


  1. Timing belt cover
    • Remove crankshaft pulley that was installed in step 9.
    • Tighten bolts to the specified torque.
Torque 17 N-m (12 lb-ft)


  1. Oil cooler hose
    • Tighten oil cooler hose bracket bolts to the specified torque.
Torque 22 N-m (16 lb-ft)


  1. Crankshaft pulley assembly
    • Using special tool J-8614-01, hold the crankshaft pulley.
    • Tighten center bolt to the specified torque.
Torque 167 N-m (123 lb-ft)


  1. Crankshaft pulley; P/S belt
    • Tighten fixing bolt to the specified torque.
Install the belt on the idler pulley.

Mar 07, 2010 | 1993 Isuzu Rodeo

1 Answer

How i fix timing of lantra 1600 cc 95


Disconnect battery earth lead. Do not turn crankshaft or camshaft when timing belt removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of ratation unless otherwise stated, Support engine. Remove, engine mounting, auxilliaty drive belts. Water pump pulley 1. Crankshaft pulley bolts 21. crankshaft pully 2. timing belt covers 3. Turn crankshaft to TDC on No 1 cyclinder. Ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket and balancer shaft sprocket timing marks aligned. Timing marks on camshaft sprockets should align with cylinder head upper face. Dowel pins on camshaft sprockets should face upwards. Slacken tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove, automatic tensioner unit bolts. Automatic tensioner unit. Timing belt, crankshaft centre bolt, crankshaft sprocket. Crankshaft sprocket guide washer. Slacken blancer shaft belt tensioner bolt. Move tensioner away from belt and lightly tighten bolt. Remove balancer shaft belt.

Installation
Ensuring timing marks arligned. Note timing marks on camshaft sprockets should align with cylinder head upper face. Exhaust sprocket mark is on recess, but inlet sprocket mark is on tooth. Note: to check oil pump sprocket positioned correctly, removing blanking plug from cylinder block. Insert 8mm diameter Phillips srcrewdriver in hole. Ensure screwdriver is inserted 60mm from face of cylinder block. if screwdriver can only be inserted 20mm: turn oil pump sprocket 360°. Insert screwdriver again. Fit balancer shaft belt in anti-clockwise direction, starting at crankshaft sprocket. Slacken balancer shaft belt tensioner bolt. Turn tensioner clockwise to tension belt. Tighten bolt to 15-22Nm. Apply thumb pressure to belt. Belt should deflect 5-7 mm. If not repeat tensioning procedure. Install crankshaft sprocket guide washer, crnakshaft sprocket. Tighten crankshaft cente bolt. Tighten torque:110-130 Nm. Note ensure crankshaft sprocket guide washer is fitted correclty. Oil treads and contact face of crankshaft body before fitting. Check tensioner body for leakage or damage replace if necessary. Check pushrod protrusion is 12mm. If not replace automatic tensioner unit. Slowly compress pushrod into tensioner body until holes aligned. Resistance should be felt. Place flat washer under tnesioner body to avoid damage to body end plugs. Retain pushrod with suitable pin through hole in tensioner body. install automatic tensioner unit to cylinder block. Tighten bolts to 22-27Nm. Fit timing belt in anti-clockwise direction, starting at the tensioner pulley. Slacken tensioner pulley bolt. Turn tensioner pully clockwise to temporarily tension belt. Tighten bolts to 43-45Nm. Turn crankshaft slowly 1/4 turn anti-cockwise. Turn crankshaft clockwise until timing marks alligned. Slacken tensioner pully bolt. Fit tool to tensioner pulley. Tool No 09244 28100. Apply clockwise torque of 2,6-2,8 Nm to tensioner pulley. Tighten bolt to 43-45Nm. Insert special tool in timing belt rear casing. Tool no 09244-28000. Screw in tool until pin can be removed from automatic tensioner unit. Remove special tool. Tool nr 09244-28000. turn crankshaft two turns clockwise. Wait 15 minutes. Ensure timing marks aligned. Check extended length of pushrod is 3,8-4,5mm. Install components in reverse order of removal. Tighten crankshaft pulley bolts, Tighten torque 20-30Nm

Nov 01, 2009 | 1995 Hyundai Elantra

1 Answer

Timing a 2.0L hyundai


RETAIN PUSHROD WITH SUITABLE PIN THROUGH HOLE IN TENSIONER BODY.
INSTALL AUTOMATIC TENSIONER UNIT TO TENSIONER BLOCK. TIGHTEN BOLTS TO 22-27.
FIT TIMING BELT IN ANTI-CLOCKWISE DIRECTION, STARTING AT TENSIONER PULLEY.
SLACKEN TENSIONER PULLY BOLT. TURN TENSIONER PULLEY CLOCKWISE TO TEMPORARILY TENSION BELT. TIGHTEN BOLT TO 43-45NM.
TURN CRANKSHAFT SLOWLY 1/4 TURN ANTI CLOCKWISE.
TURN CRANKSHAFT CLOCKWISE UNTIL TIMING MARKS ALIGNED.
SLACKEN TENSIONER PULLEY BOLT. FIT TOOL TO TENSIONER PULLEY.
APPLY CLOCKWISE TORQUE TO TENSIONER PULLEY. TIGHTEN BOLTS.
INSERT SPECIAL TOOL IN TIMING BELT REAR CASING.
SCREW IN TOOL UNTIL PIN CAN BE REMOVED FROM AUTOMATIC TENSIONER.
REMOVE SPECIAL TOOL.
TURN CRANCSHAFT TWO TURNS CLOCKWISE. WAIT 15 MINUTES.
ENSURE TIMING MARKS ALIGNED.
CHECK EXTENDED LENGTH OF PUSHROD IS 3.8 - 4.5MM
RE-ASSEMBLE

Jul 15, 2009 | 1998 Hyundai Tiburon

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

2 Answers

Honda accord ex 92


Crankshaft pulley (harmonic balancer) removal- disconnect neg battery cable, remove belts, it would be a good idea to soak the bolt w/ penetrating oil overnight, there is a special 'crankshaft pulley holding tool' available to secure the pulley while removing and installing the bolt. Some parts stores loan tools for free if u purchase parts from them, I don't know if this is available, but it would be worth checking out. Attach holding tool and remove bolt securing pulley. Carefully remove pulley from crankshaft, Do NOT pry off. Remove key from crankshaft sprocket,
Install: install key on crankshaft sprocket, slide pulley on, apply clean oil to bolt threads but NOT to washer contact surfaces, secure crankshaft w/ holding tool, tighten to 159 ft lbs (91-93 Accord), install belts, re-attach neg cable.

Nov 11, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1997 Isuzu Rodeo Logo

Related Topics:

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...