Question about Dodge Pickup

1 Answer

I need to know what diagnostic code p1762 means

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 77,202 Answers

Dodge: Governor pressure sensor offset improper voltage Dodge: Governor pressure sensor offset improper voltageFault Code P1762: Automatic transmission Governor pressure sensor offset improper voltage

Posted on Sep 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 dodge dakota 3.9 liter2wd a/t check engine light on and flash 12 times


Hi the P1762 means,overdrive band failed off,hope this was some help,all the best.

Nov 11, 2015 | Dodge Cars & Trucks

1 Answer

P1762


this is transmission related error. there is a governer pressure selenoid in selenoid pack of transmission. a sensor measures the voltage ouput of that. so this error means that its voltage readings were off spec. so you need to check the selenoid or sensors. (inside transmission)

but before investing money on, if your car was parked for long time, try to drive for 3 or 4 warm up period. which means drive let it cool down and drive again. then reset it by disconencting negative battery cable (remember to save code of radio if any)

Nov 22, 2011 | 2003 Jeep Grand Cherokee

1 Answer

I have a code p1762 for my 97 jeep grand cherokee


Trouble code P1762 means: Governor pressure sensor offset improper voltage. Gov. Pressure Sensor.It is located in the valve body of the transmission and requires dropping the transmission pan to replace. Sounds much more difficult than it is. Since you have to change your fluid it's a good idea to change the trans. filter .

Feb 01, 2011 | 1997 Jeep Grand Cherokee

2 Answers

Fault codes p1757 p1762 when i doing smoke for dmv when i doing smoke test this code show fault on transmision


CODE P1757 - GOVERNOR PRESSURE GREATER THAN 3 PSI WHEN REQUESTED TO BE O. CODE P1762 - GOVERNOR PRESSURE SENSOR OFFSET VOLTS TOO LOW OR HIGH.MEANING SENSOR INPUT GREATER OR LESS THAN CALIBRATION FOR 3 CONSECUTIVE NEUTRAL PARK OCCURANCES.

Sep 01, 2010 | 2000 Jeep Cherokee

1 Answer

I have a code that i would like identified p1762


P1762 - Gov Press Sen Offset Volts Too Low or High

Jun 30, 2010 | Dodge B Series Cargo Cars & Trucks

1 Answer

What do these codes mean? P1763 and P1762


Those codes indicate an issue with the Governor pressure sensor and the transducer which you'll have to replace. To replace them you'll have to drop the transmission pan to see them. Remove the bolts and disconnect the wiring clips to remove them.

Nov 19, 2009 | 1999 Dodge Durango

2 Answers

Diagnostics "P1762 Manufac. Contrl. Transmission"


Had the same code on my 2002 Jeep Grand Cherokee. Started having shifting problems as well. Code is for governor pressure sensor on trans. Cost me about $800 for dealer to fix. No problems after part changed out.

May 22, 2009 | 2002 Jeep Grand Cherokee

1 Answer

P1762


I had the same problrm a couple weeks ago I ended up replacing the governor pressure sensor and the solenoid it is very easy you just drop the pan and it is right there. Here is a website that shows you how to do it http://forums.minnesotamud.com/showthread.php?p=48356

Feb 02, 2009 | 2001 Jeep Grand Cherokee

1 Answer

P1762


Looks like the fautl code refers to the stuck solenoid on the shift control valve which is in the valve body.
It is a job that requires lots of precision and probably if you take the valve body out you'll need a plan to reassemble it...I would suggest getting it to a specialist.
Cheers

Feb 02, 2009 | 2000 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

826 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...