Question about 1995 Ford Mustang

Open Question

The oil dipstick tube for my 1995 ford mustang came loose from engine end. how do i repair this problem

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 214 Answers

SOURCE: How do I replace the oil dipstick tube?

The dipstick can be pulled out of the block with a pair of vicegrips and the new one driven down into the block. Before trying to pull the dipstick tube out make sure it is not held onto the block with a small bolt.

Posted on Jan 20, 2010

  • 46 Answers

SOURCE: Oil blowing out the dipstick tube

a fairly common problem on any of those high mile or abused 4.0liter engine either #1 your PCV ventilation tubes are plugged those are thos small black lines comming out of your valve cover or #2 your getting really bad blow by in your valves. 1 being easy to do and 2 not so easy!!

Posted on May 26, 2008

  • 255 Answers

SOURCE: 1995 Ford Mustang Engine Won't Turn Off

the ign switch should take care of it i agree with you


Posted on Apr 19, 2009

  • 162 Answers

SOURCE: Oil Dipstick tube is broke, Where does it go?

Posted on Jul 27, 2009

  • 410 Answers

SOURCE: where is the transmission dipstick on 1995 Isuzu redeo?

There is no transmission dipstick. You have to both check and add fluid to these vehicles from underneath the vehicle. Find the transmission fluid pan and you will find two plugs. The lower plug will drain the pan and the upper one you can add fluid or check the fluid level. You will know that the level is correct when the plug is out and fluid barely leaks out of the hole. You don't want a lot coming out because you don't want to overfill. In order to get it into the hole you have to be some sort of tube to attach to the top of the bottle. They sell these types of tubes at your auto part store and they just screw on. It is very awkward, but you can actually put the bottle high enough to get the fluid in if you put it right to the left of the pan. The first time I did this on mine it was a pain but once you figure it out you will be good to go. Let me know if you have any other questions about your vehicle. Thanks for rating my response and for using FixYa!

Posted on Sep 05, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Canyou tell mei dont know where on block the dipstick tube attaches

its on de right site you stand front the car (steer) gearbox automatic
is left site .

Jun 08, 2014 | 1995 Ford Mustang

1 Answer

Explorer Dipstick Tube Broke

There is a bracket that holds the tube to the block. There is no clips or retainers that hold it in the block. With the bracket loose you can twist and remove from the block. There is a oil ring on the end of the tube.
Sometimes the old tube is hard to remove...due to rust and corrosion. Spray the tube with a good penetrating oil before you start. Try to wiggle and twist the tube to brake it careful, the tube is thin. If the tube breaks off flush with the block..the piece that in the block will need to get extracted out or remove the oil pan and remove it that way.

Nov 25, 2012 | 2006 Ford Explorer

1 Answer

Once again, I'm going to ask where the oil dipstick tube goes into a 1995 ford mustang with a 3.8L v6 engine. I can't find the hole where it goes in, (probably because I have no way to get the car...

how about you go to the library and take out a book on your car so you can have it as you look for the place the dipstick goes,and how its routed along side the motor.

Aug 05, 2011 | 1995 Ford Mustang

1 Answer

Need to remove oil pan off 1965 Ford Mustang with i6 170. How do I do it?

With out pulling the engine out you need to take the motor mouts loose rise the engine as high as you can drop the oil pan out the back you might have to take oil pump or oil pump pick up tube off

Jun 26, 2011 | 1965 Ford Mustang

1 Answer

I can't find my dipstick in my ford 1995 mustang

Here are some places to check, as it varies on year, engine type, and they made a lot of changes over the years on these.

First would be the oil fill tube. That is a good place to start. If not there, check along front of the engine or the right and left sides towards the rear of the engine. The dipstick should be marked with a yellow handle. Red is transmission.

Let me know,


Apr 11, 2010 | 1995 Ford Mustang

1 Answer

Need to know how to check oil in transmition in a 95 ford aspire

Check the engine oil level every time you fill the gas tank. The car should be on level ground when checking the oil.
  1. Turn the car off and wait several minutes.
  2. Locate the engine oil dipstick and withdraw it from the tube.
  3. Wipe the dipstick with a clean rag and reinsert it in the dipstick tube.
  4. Remove the dipstick again, hold the dipstick horizontally and observe the level of the oil.

Fig. 1: Grasp the engine oil dipstick and withdraw it from the tube

Fig. 2: Observe the oil level on the dipstick and add oil if it is low

  1. The oil level should be at the FULL mark on the dipstick.
  2. If the level is at or near the LOW mark, replace the dipstick and add fresh oil to bring the level up to the FULL mark. Do not overfill.
  3. Recheck the oil level and close the hood.

Good luck, and remember rated this help!!!

Aug 18, 2009 | 1995 Ford Aspire

1 Answer

I purchased an engine without a tube or dip stick, and do not know what I should purchase, and where these will fit into the engine? I need to know where the oil dip stick and tube are located on the...

the dipstick and tube go to the sump it is at the very bottom of the engine block should be a large smooth pan looking thing that covers the bottom of the engine, dont know where you can purchase these things but go to a place that sells car parts and put an order in for the parts with your engine make and model number

May 11, 2009 | 1966 Ford Mustang

1 Answer

The oil dip stick tube was out of the block

will be on driver side rear location you will need to get under car and feel around you will find the hole in that area then you can replace the dipstick housing

Dec 15, 2008 | 1995 Ford Mustang

1 Answer

Broken Dip Stick

Most dipstick tubes are a "press fit" into the engine block, and can usually be removed without pulling the engine (if you can get to it).

However, it may be broken off too short, or the mechanic simply cannot reach it with the engine in the car.

Personally, I would get a second opinion before you pay all that money to get a $10 dipstick tube to be replaced.

Try the local Ford dealer. Most of the time, a seasoned dealer mechanic knows "tricks" to do different things.

Jun 23, 2008 | 1995 Ford Mustang

Not finding what you are looking for?
1995 Ford Mustang Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79024 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5676 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides