Question about 1989 Pontiac 6000

Open Question

How do you change a starter on a 1989 Pontiac 6000 le 2.8 liter v6

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 231 Answers

SOURCE: timing a pontiac 6000le 2.5 engine

first check to be sure the vavuum lines at the throttle body are in there correct places.
on the main pulley of your engine, the one on the crank shaft there will be a little notch on it. mark the notch with some chalk or a dab of white paint. then loosen the bolt that holds down the distributor until you can turn the distributor. turn the distributor a little bit, snug the bolt up and try it. once you have the car running you will need a timing lite to set the timing to the correct timing mark. which should be 8 degrees before top dead center for you car.

Posted on Oct 12, 2008

Ad
  • 109 Answers

SOURCE: Changed starter and now we get a revving/whirring sound

It sounds like the starter is not engaging the flywheel to crank it and is just spinning. If it were mine, I'd pull the starter out and see if anything looks strange and see if the starter gear moves easily.

Posted on Nov 20, 2008

  • 21 Answers

SOURCE: 1989 Pontiac 6000 LE

Check AutoZone.com as they have an area where they can tell you where the parts are located on your car.

Posted on Apr 07, 2009

  • 1 Answer

SOURCE: 1989 dodge raider starter problem

It is avery simple starter to remove, two bolts 9/16 , and a1/2" wrench, undo youy battery cables so as not spark,cause fire etc.. i just paid $ 93.00 dollars for my starter. great little truck it will climb any thing.

Thank you T.Morrow


Posted on Apr 11, 2009

emissionwiz
  • 76673 Answers

SOURCE: need to find starter on 1996 pontiac grand am

bottom rear of engine at the transmission bell housing, u will need to jack the car up to change it out..

Posted on Jun 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 1989Pontiac 6000 LE it won't start. It has new battery starter and altermator. I turn key and have nothing no clicking noise or nothing. Any help greatly appreciated


When turning the key to start measure for B+voltage at the S terminal on the starter solenoid . If no B+ voltage possible bad park neutral safety switch . check For B+ voltage at the heavy gage battery cable on the starter while trying to cranking the engine , less then battery voltage , bad cable . Find starter voltage drop testing on youtube , watch the video . Also starter circuit testing .

Apr 04, 2017 | 1989 Pontiac 6000

1 Answer

1989 pontiac 6000 le, car died while driving, had it towed , it started several times afterwards. Car was driven 1/2 mi and it died again, this time for good. Car will crank but will not start. Have...


check to see if the starter is ingaging or making a clicking sound when you have the hood up. If you do not hear the starter ingaging then its your starter but also you might have a ground issue too so use a multimeter if you know how and have one check things with this to see if there might be any short to the ground of car plus there might be bolts lose or missing as well you should check.

May 27, 2011 | 1989 Pontiac 6000

1 Answer

Cannot figure out how to test the crank shaft position sensor to see if it has caused recent ignition failure because the harness has three leads at the end that connects to the ignition modual and two...


If you unplug the crank sensor at the module and measure the resistance of the crank sensor. (the yellow wire and the black wire) The resistance of the crank sensor should be 900-1200 ohms.

May 17, 2010 | 1989 Pontiac 6000

1 Answer

1989 pontiac 6000 le eating fuel just had a complete tune up still did not help


do a code search
check the cats then check the fuel system and fuel presure reg

but do a code search first

Jan 13, 2010 | 1989 Pontiac 6000

3 Answers

1989 Pontiac 6000 LE


Check AutoZone.com as they have an area where they can tell you where the parts are located on your car.

Jan 03, 2009 | 1989 Pontiac 6000

2 Answers

Fuel Pump Relay Switch


Underneath your hood, behind the passenger side headlight, behind the core support, is a bank of 2-8 relays. One of those relays is the relay needed for your fuel pump. There will also be a fuel pump relay fuse located there. The relay designation should be on the cover of the relay compartment.

Jan 03, 2009 | 1989 Pontiac 6000

1 Answer

Changed starter and now we get a revving/whirring sound


It sounds like the starter is not engaging the flywheel to crank it and is just spinning. If it were mine, I'd pull the starter out and see if anything looks strange and see if the starter gear moves easily.

Nov 20, 2008 | 1991 Pontiac 6000

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...