Question about 1999 Dodge Caravan

1 Answer

Both turn signals come on when one is turned on in either direction

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Sounds like maybe a multi function switch does everything else work on it?

Posted on Oct 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Directions to replace a front turn signal bulb; 09 Caddy


look at the back of it . twist and turn , pull out .

Feb 25, 2016 | Cars & Trucks

1 Answer

Turn signal relay by left foot needs replaced. I can't figure out why it won't pull out of the convenience center. Is there a retaining device I'm missing?


GM Turn Signal Problem Fix - Directional Relay Replacement

? 5:38
www.youtube.com/watch?v=y4QVUBVVVpI
May 3, 2014 - Uploaded by Steve O
GM Turn Signal Problem Fix - Directional Relay Replacement ....You will need to install resistors in series with the directional LEDs

Sep 22, 2015 | Cars & Trucks

1 Answer

My turn signals in '03 olds alero dont always work. When they dont, if i push hazard button my signals will work again. I already replaced the turn switch stick on the steering column n continue to have...


Its not the flasher.

The hazzard switch is the most likely culprit since it directs current to either the turn signal switch or directly to the turn signal lights depending on its position. Over time the contacts wear out in the flasher switch. When you push it in and out you are allowing good contact to return to the normally off function that routes power to the turn signal switch.

The flasher switch can be found at any good parts store.

Oct 02, 2014 | Cars & Trucks

1 Answer

All 4 turn signals dont work


there should be a fuse for the direction light. and a direction switch can be bad and still click and operate as it suppose to

Dec 21, 2012 | 1997 Geo Metro

1 Answer

My turn signals on my 1988 Jeep Comanche dont work.


My first guess would have been the turn signal switch, which you said you replaced.
You'll have to get a wiring diagram of the switch and start testing wires for power out of the switch. Could be a problem with the main harness going back to the rear of the truck, or a ground for those sockets.

Oct 12, 2012 | 1988 Jeep Comanche

3 Answers

1993 Geo Prizm turn signals dont work. Hazard lights DO work. Checked fuse several times & its ok. Any suggestions?


You have a bad turn signal switch if the hazards work and the turn signals do not. It has nothing to do with the fuse or the flasher unit. Your switch is bad or you have a bad connection some where.

Feb 15, 2010 | Geo Prizm Cars & Trucks

1 Answer

How do I remove the ignition lock cylinder from the steering column on a 1978 Jeep CJ7. I already have the steering column disassembled.


here are the instruction the first set are the instruction on how to remove the turn signal switch as you will need them to remove the ignition

Removal & Installataion of turn signal switch
  1. Disconnect the negative battery cable.
  2. Remove the steering wheel.
  3. Loosen the anti-theft cover retaining screws on 1976 models and lift the cover from the steering column. It is not necessary to completely remove these screws.
  4. Depress the lockplate and pry the round wire snapring from the steering shaft groove. A lockplate compressor tool is available for compressing the lockplate.
  5. Remove the lockplate, directional signal canceling cam, upper bearing preload spring, and thrust washer from the steering shaft.
  6. Move the directional signal actuating lever to the right turn position and remove the lever.
  7. Depress the hazard warning light switch and remove the button by turning it counterclockwise.
  8. Remove the directional signal wiring harness connector block from its mounting bracket on the right side of the lower column.
  9. On vehicles equipped with an automatic transmission, use a stiff wire, such as a paper clip, to depress the lock tab which retains the shift quadrant light wire in the connector block.
  10. Remove the directional signal switch retaining screws and pull the switch and wiring harness from the steering column.
  11. Guide the wiring harness of the new switch into position and carefully align the switch assembly. make sure that the actuating lever pivot is correctly aligned and seated in the upper housing pivot boss prior to installing the retaining screws.
  12. Install the directional signal lever and actuate the directional signal switch to assure correct operation.
  13. Place the thrust washer, spring, and directional signal canceling cam on the upper end of the steering shaft.
  14. Align the lockplate splines with the steering shaft splines and place the lockplate in position with the directional signal canceling cam shaft protruding through the dogleg opening in the lockplate.
  15. Install the snapring.
  16. Install the anti-theft cover.
  17. Install the steering wheel and connect the negative battery cable.
  18. Check the operation of the turn signal switch.

Removal & Installation of ignition lock switch
  1. Disconnect the battery ground cable.
  2. Remove the turn signal switch as described earlier in this section. You don't have to remove the switch completely, just set it aside.
  3. Insert the key. Position the key as follows.
    • 1976-83: With manual transmission, put it in the ON position; with automatic, put it in OFF/LOCK.
    • 1984-86: Two detent positions, clockwise, beyond OFF/LOCK.
  1. Working through the slot next to the turn signal switch mounting boss, use a thin screwdriver to release the lock cylinder.
  2. To install, insert the key in the new lock cylinder. Hold the sleeve and turn the key clockwise until it stops. Align the cylinder retaining tab with the housing slot and insert the cylinder. Push the cylinder in, rotate to engage, then push in until the retaining tab engages the housing groove.
  3. Complete the procedure in the reverse of removal.

Aug 20, 2009 | Jeep CJ7 Cars & Trucks

1 Answer

Directional signal won't turn off


check your hazard switch aka emergency switch. 

Apr 15, 2009 | 1996 Honda Accord

Not finding what you are looking for?
1999 Dodge Caravan Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...