Question about Daewoo Lanos

Open Question

Im trying to change the front brakes on a 1995 daewoo cielo. the calaper is connected to the hub with two allen bolts and they wont turn . it seems siezed. i can only put one new pad in. how do i get that calaper to move.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: daewoo cielo speedo problem

Oh, i had this problem! you need to replace the clock i don't know the name but you need to replace the thing that shows you in which speed you are and the time and things.

Posted on Jun 17, 2008

Ad
  • 56 Answers

SOURCE: Daewoo Cielo losing power

DEALER ISSUE, TAKE IT TO THEM.

Posted on Oct 13, 2008

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

tse22
  • 103 Answers

SOURCE: Changing Rear brake pads 2005 dodge grand caravan

There are 2 bolts on the "inside" on the caliper towards the bottom they use an allen wrench socket.

Posted on May 13, 2009

  • 1 Answer

SOURCE: waht size allen key to remove front brake calipers

On my Golf 1.9TDI (2005) both top and bottom Calliper fastenings have a 7mm Allen bolt thus you will need a non standard 7mm Allen Key not 12 point

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get stripped Allen bolts out to get rotor an hub off


What is the make and model of the vehicle you are trying to remove the Allan bolt from. Be sure to look between the shoe and the bracket for the bolt, some of the brakes have a jam nut there and they will turn and make it seem like the bolt is stripped. You have to put a wrench on the jam nut while turning the Allan bolt.

Dec 20, 2015 | Cars & Trucks

1 Answer

I had both front end hubs replaced on my 2004 Siverado 1500 pick up truck. What is a hub?


hub took the place of old wheel bearing know they are seald bearings easy to replace remove brake calaper an three or four bolts an king nut if fourwheel drive sorry i cant spell haha

Dec 16, 2010 | 2004 Chevrolet Silverado

1 Answer

How to replace hub assembly on a 1999 cheve silverado driver side only! And what tools needed


2 wheel drive?
1 jack, 1 jackstand, 1 lug wrench,1 pair of channel lock pliers,1 pair side cut pliers1 3/8 or 10mm allen wrench, 1 six to 8 inch c clamp, 1 small pry bar grease,rags,.
place jack under truck same as changing tire,jack up and put jack stand under frame,remove tire,then using allen wrench,s remove allen bolts on inside of brake caliper,pry caliper off gently so as to not damage the brake pad,use a piece of wire and hang caliper so it does not hang on brake hose,then pull or pry the center hub cap off this will expose the bearingretaing nut there should be a cotter key in front of the nut,use the side cut pliers and straighten the cotter key then pull it out,remove the retaining nut and and crown washer,then pull the hub and bearing assembly off.
installation is in reverse,put hub and greased bearings on spindel tighten center nut while turning hub and tighten the nut very tight,the hub will be very hard to turn then start loosening the spindle nut and spinning the hub,holding the top of the hub push in and out if you feel it rocking on the bearings it is to loose tighten the slowly until there is no play put a cotter back in, put the small hubcap back on then using the c clamp and a piece wood put the c clamp over the back of the brake caliper and slide the piece over the piston cup on the inside to protect the piston,tighten the clamp until the piston is colapsed all the way, put brake pads back on put caliper on,put a small amount of grease on the smooth part of the allen bolts not on the threads,tighten the bolts.
put the tire assembly back on,remove jack stand and jack,
this is the important part,
1 be sure all bolts and fasteners are on and tight.
2 when you get in the truck and start it leave it in park,gently push the brake pedal down part way and let up do this until the pedal becomes firm.
3 after you drive five or ten miles recheck every thing.
Hope this helps.

May 14, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

How do i replace the front wheel brake discs on my 1995 discovery 300


Remove the front wheels and four wheel drive hubs.
The hub is pressed off using a bolt threaded in the center to push on the front axle.
Remove the hub to disc bolts.
Replace the disc and reinstall the disc to hub bolts torqued to 73 Newton Meters with loctite 270 applied to the threads.

Feb 24, 2010 | 1995 Land Rover Discovery

1 Answer

How to change rear brake pads on audi a6 2006


Remove the tires, Remove the calaper bolts, (small heads on them 12mm or so) Remove calaper, Pads are setting in a holder. Lube new pads with litheum grease and place in holder. (look at old pads, one or both may have small metel tab on one end) If the new pads have the tab, put that pad where the old pad with the tab was. (ie. tab to the inside) Press pistion in with a 'C' clamp. If it won't go in easly, it may screw in. If the parking brake cable is hooked to the calaper, it probly screws in. Use large pliers to screw in calaper piston. Place calaper over pads and install bolts (lube bolts) Rember to pump brakes befor driving . to get a solid peddle.

May 20, 2009 | 2006 Audi A6

1 Answer

Brake rotor replacement


you should only have to take off the tire and the calipers, and the caliper bracket, there is no hub on the front wheels. there should be 2 bolts holding on the caliper bracket, usually with a big allen screw. they may be stuck so use a hammer to tap them loose. good luck

Nov 28, 2008 | 1994 Hyundai Excel

2 Answers

2004 Toyota Camry Brakes


Raise the vehicle up and remove the rims & tires

Remove the brake pads, and then remove the calipers from the caliper retention brackets, do NOT remove the brake hoses from the calipers.

Remove the caliper retaining brackets from the hub assemblies (2 large bolts on backside of the bracket)

Tap the brake rotors off of the hubs, hit them from the back side of the rotor.

No big mysteries here, this is a very easy job.

Oct 21, 2008 | 2004 Toyota Camry

1 Answer

Daewoo lanos


your brakes are keeping i on the dum try a puller and a hammer

Oct 18, 2008 | 1999 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...