Question about Ford Ranger

1 Answer

How do you remove clutch t/o bearing? - Ranger Ford Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Drop the transmission. It rides on the finger-like springs of the pressure plate.

Posted on Sep 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i replace a clutch on a 2008 scion xb


There is a video about this on line

I would suggest that you get a paperback repair manual like a Haynes to help you if you do it yourself. Or sign up at Autozone.com and see if they have any downloadable free guides specific to XBs. Autozone won't spam you for signing up.

Feb 07, 2015 | 2008 Scion Xb

1 Answer

My 94 grand marquis shut off seconds after a loud grinding noise that sounded like it was coming from the front left hand side. I tried turning it back on after it happened and the check engine and oi


I interpret this as the Passengers side of your car. Usually the serpentine belt breaks when the A/C compressor seizes. That is the part which is probably grinding or the A/C clutch bearing is seized.

Although this is Winter, the Defroster is made to activate the compressor to lube it during the Winter. Now the pulley that turns the compressor has a clutch bearing. It is ALWAYS turning when the engine is on except when electricity is applied to the compressor clutch and it locks and turns the A/C compressor shaft.

What needs to be done now is to determine if the A/C clutch bearing is bad or if the A/C compressor is bad. Most A/C clutch bearings can be removed and replaced. SOME of the bearings within the A/C clutch can be changed and then they are as good as new.

The procedure for replacing the bearing is 1 step beyond replacing the entire A/C clutch. The fan shroud must be removed, the serpentine belt must come off, then a small bolt and a retaining clip must be removed and the clutch slid off the compressor.

There is no need to remove the compressor or lose Freon. The bearing situation can be determined once the serpentine belt is removed and the parts turned by hand.

Jan 20, 2014 | 1994 Mercury Grand Marquis

1 Answer

I need to know how to replace the clutch in a 1993 colt vista


0900c1528004723e.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Clutch release bearing - 1990 Colt hatchback and sedan w/ 1.6L engine, 1990 Colt Wagon w/1.8L engine, and 1990-93 Vista


0900c1528004723f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Clutch driven and drive discs - 1990-93 all models


0900c15280047240.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Clutch release bearing - 1990 Colt Wagon w/1.5L engine, 1991-92 Colt hatchback and sedan w/4-speed and 1993 Colt hatchback and sedan w/1.8L engine

  1. Remove the transmission or transaxle as outlined.
  2. Insert a pilot shaft or an old input shaft into the center of the clutch disc, pressure plate, and the pilot bearing in the crankshaft.
  3. With the pilot tool supporting the clutch disc, loosen the pressure plate bolts gradually and in a crisscross pattern.
  4. Remove the pressure plate and clutch disc.
  5. Clean the transmission and clutch housing. Clean the flywheel surface with a non-oil based solvent. Wash your hands before installing or handling the clutch assembly parts. Hold the clutch disc by the center hub only.

Before assembly, slide the clutch disc up and down on the transmission input shaft to check for any binding. Remove any rough spots with crocus cloth and then lightly coat the shaft with Lubriplate.
  1. To remove the throwout bearing assembly: Remove the return clip and take out the throwout bearing carrier and the bearing.
  2. To replace the throwout arm use a / 16 in. punch, knock out the throwout shaft spring pin and remove the shaft, springs, and the center lever.
  3. Do not immerse the throwout bearing in solvent; it is permanently lubricated. Blow and wipe it clean. Check the bearing for wear, deterioration, or burning. Replace the bearing if there is any question about its condition.
  4. Check the shafts, lever, and springs for wear and defects. Replace them if necessary.
  5. If you hadn't planned on replacing the clutch disc, examine it for the following before reusing it. Loose rivets. Burned facing. Oil or grease on the facing. Less than 0.3mm left between the rivet head and the top of the facing.
  6. Check the pressure plate and replace it if any of the following conditions exist: Scored or excessively worn. Bent or distorted diaphragm spring. Loose rivets.
  7. Insert the control lever into the clutch housing. Install the two return springs and the throwout shaft.
  8. Lock the shift lever to the shaft with the spring pin.
  9. Fill the shaft oil seal with multipurpose grease.
  10. Install the throwout bearing carrier and the bearing. Install the return clip.
  11. Grease the carrier groove and inner surface.
  12. Lightly grease the clutch disc splines.

The clutch is installed with the larger boss facing the transmission.
  1. Support the clutch disc and pressure plate with the pilot tool.
  2. Turn the pressure plate so that its balance mark aligns with the notch in the flywheel.
  3. Install the pressure plate-to-flywheel bolts head-tight. Using a torque wrench and, working in a crisscross pattern, tighten the bolts to 11-15 ft. lbs.
  4. Install the transmission or transaxle as outlined.
  5. Adjust the clutch as described in the following information.

Jan 07, 2013 | Cars & Trucks

1 Answer

How clutch replacement


disconnect battery, remove starte motor, remove drive shafts, support and remove cross member,remove clutch slave cylinder, remove bellhousing bolts and while suspending transmission remove and lower transmission.//remove preasure plate and clutch. Good idea to replace spigot bearing and throw out bearing while you do job. allow 4-5 hrs for r&r. Refit in reverse order.

Nov 17, 2012 | 1987 Toyota 4Runner

1 Answer

Clutch noise and vibration when fully pressed


This is caused by a defective clutch pressure release bearing, the release bearing is the only part that can cause this symptom. To replace the clutch release bearing requires the transmission be removed from the car, the release bearing rides on the input shaft collar of the transmission input shaft which goes into the clutch disk. If you replace the release bearing you should have the clutch disk and pressure plate replaced at the same time as the labor cost is about the same just to do the bearing.

Oct 31, 2011 | 2008 Volvo V50

2 Answers

Which side of the clutch does throw out bearing go on


The throw out bearing will be on the outside of the clutch assemble. What it does is push against the fingers in the center of the pressure plate.

Mar 08, 2011 | 1992 Acura Vigor

2 Answers

I need instructions on replacing the clutch in a '94 Chevy Blazer 4x4, 350 engine. Specifically the pilot bearing, throwout bearing.


The pilot bearing is pressed into the flywheel and you need a pilot bearing/bushing puller. Some A/P stores will rent it to you for free (deposit). the throwout bearing is held onto the clutch fork normally by clips. Sometimes you have to take the "fork" out to get the bearing off.

Make sure to note how "deep' the pilot bearing/bushing is so that when you install the new one it is set at the right depth.

Jan 01, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

How get to flywheel bolts


In the Toyota Pick-ups/Land Cruiser/4Runner 1989-1996 (free register) can find several graphics about this.

Driven Disc and Pressure Plate - REMOVAL & INSTALLATION

(see Figures 1 through 27).

cc66ac3.jpg


CAUTION The clutch driven disc may contain asbestos, which has been determined to be a cancer causing agent. Avoid inhaling any dust from any clutch surface! When cleaning clutch surfaces, use a commercially available brake cleaning fluid. Never clean clutch surfaces with compressed air.
  1. Remove the transmission.
  1. Matchmark the clutch cover (pressure plate) and flywheel, indicating their relationship.
  1. Loosen the clutch cover-to-flywheel retaining bolts one turn at a time in a crisscross pattern. The pressure on the clutch disc must be released GRADUALLY.
  1. Remove the clutch cover-to-flywheel bolts. Remove the clutch cover and the clutch disc.
  1. If the clutch throwout bearing is to be replaced, do so at this time as follows:
  1. Remove the bearing retaining clip(s) and remove the bearing and hub.
  2. Remove the release fork and the boot.
  3. The bearing is press fit to the hub. Turn the bearing by hand while placing it under some pressure; check for freedom of motion and lack of grinding or resistance. The bearing is permanently lubricated and cannot be disassembled or greased.
  4. Clean all parts; lightly grease the input shaft splines and all of the contact points.
  5. Install the bearing/hub assembly, fork, boot, and retaining clip(s) in their original locations.
  1. Inspect the flywheel surface for cracks, heat scoring (blue marks), and warpage. If oil is present on the flywheel surface, this indicates that either the engine rear oil seal or the transmission front oil seal is leaking. If necessary, replace the seal(s). If in doubt concerning the condition of the flywheel, consult an automotive machine shop.
  1. Before installing any new parts, make sure that they are clean. During installation, do not get grease or oil on any of the components, as this will shorten clutch life considerably. Grease or fingerprints may be cleaned with an evaporative cleaner such as the type used on brake linings.

To install:
  1. Position the clutch disc against the flywheel. The long side of the splined section faces the flywheel.
  2. Install the clutch cover over the disc and install the bolts loosely. Align the matchmarks made. If a new or rebuilt clutch cover assembly is installed, use the matchmark on the old cover assembly as a reference.

Whenever the clutch disc is replaced, replacement of the pressure plate (clutch cover) and release bearing is highly recommended.
  1. Align the clutch disc with the flywheel using a clutch aligning tool. These handy tools are available in many auto parts stores at a reasonable price. Do NOT attempt to align the clutch disc by eye; use an alignment tool.
  1. With the clutch aligning tool installed, tighten the clutch cover bolts gradually in a star pattern, as is done with lug nuts. Final tighten the bolts to 14 ft. lbs. (19 Nm).
  2. Apply molybdenum disulfide grease or multi-purpose grease to the release fork contact points, the pivot and the clutch disc splines. Install the boot, fork, and bearing on the transmission input shaft.
  3. Install the transmission.
Hope helped.

Mar 15, 2010 | Toyota Pickup Cars & Trucks

1 Answer

How do you replace a throw out bearing on a 88 integra ls?


You must remove the transmission from the vehicle. The clutch release bearing (throwout bearing) rides on the input shaft of the transmission, and is the only part of the clutch kit that remains attached to the transmission upon removal.

Make certain you reattach the bearing retainer mechanism to the bearing fork, so that the bearing doesn't ride on the face of the pressure plate while you're not using the clutch pedal.

Dec 27, 2009 | 1988 Acura Integra

1 Answer

How do I get the clutch to release from the transmission on a evo


All 1996 Model Year and newer vehicles
equipped with manual transaxles except Accents
, which have the "push" type clutch system. SERVICE PROCEDURE:
  • Drain the transaxle gear oil.
  • The reference photo to the right shows the clutch related components as viewed from outside the transaxle case.
75c260f.jpg Loosen the release lever nut and washer
Separate the release lever by removing the snap pin and clevis pin.
Separate the release lever from the fork shaft.
Loosen the bolts attached to the release cylinder and separate the release cylinder from the transaxle assembly (no need to open the clutch hydraulic system).
  • Remove the transaxle assembly after removing each bolt attached to the engine assembly.
  • Remove the clutch cover assembly. The release bearing is still attached.
To separate the release bearing from the clutch cover, rotate the release bearing to gain access to the bearing snap ring.

5affa6e.jpg

Mar 28, 2009 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...