I like to have a video step by step in pulling out cylinder head sentra 95 model

Main Cylinder head Bolts
all
step 1 = 88-98 Nm, 65-72 lb.ft

147 mm, 5.8 inch bolts
step 2 = 85-95°

119 mm, 4.7 inch bolts
step 2 = 70-80°

Cylinder head Sub Bolts
step 1 = 34 Nm, 25 lb.ft
step 2 = 44-54 Nm, 33-40 lb.ft

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

1. Step 1: 72 ft. lbs. (98 Nm).
   
2. Step 2: Completely loosen all bolts.
   
3. Step 3: 26-32 ft. lbs. (34-44 Nm).
   
4. Step 4: plus 90-95 degrees clockwise.
   
5. Step 5: plus 90-95 degrees clockwise.

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine




Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Hi there:



Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

1. Step 1: 72 ft. lbs. (98 Nm).
   
2. Step 2: Completely loosen all bolts.
   
3. Step 3: 26-32 ft. lbs. (34-44 Nm).
   
4. Step 4: plus 90-95 degrees clockwise.
   
5. Step 5: plus 90-95 degrees clockwise.

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine




Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

1.8L 4 cylinder

cylinder head bolt torque

bolts 1-10 ( large bolts )

step 1 21 ft lbs.
step 2 44 ft lbs.
step 3 loosen all bolts
step 4 21 ft lbs.
step 5 additional 50-55 degrees

bolts 11-15 small bolts

56-74 in. lbs

2.0L 4 cylinder

step 1 29 ft lbs.
step 2 58 ft lbs.
step 3 loosen all bolts
step 4 23-25 ft lbs.
step 5 additional 90-95 degrees
step 6 additional 90-95 degrees

from autozone.com:

1. Tighten the cylinder head bolts in the sequence shown in three steps, as follows:
   1. Step 1-27-31 ft. lbs. (37-43 Nm).
   2. Step 2-tighten an additional 85-95 degrees.
   3. Step 3-tighten another 85-95 degrees.

Fig. Fig. 9 Tighten the cylinder head bolts in three steps using the sequence shown-4.6L and 5.4L engines

2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Cylinder Head Bolt

Step 1 28-31 (37-43 nm)
Step 2 Additional 85-95 Degrees
Step 3 Loosen 360 Degrees
Step 4 28-31 (37-43 nm)
Step 5 Additional 85-95 Degrees
Step 6 Additional 85-95 Degrees

Sequence:
http://www.anubiscycle.com/fixya/2001expedition46sequence.png

Cylinder Head Bolt
Crown Victoria & Grand Marquis
Specs are given in ftlbs

Step 1 28-31
Step 2 Additional 85-95 Degrees
Step 3 Loosen 360 Degrees
Step 4 28-31
Step 5 Additional 85-95 Degrees
Step 6 Additional 85-95 Degrees

Source: Mitchell1 OD

1. For 1.8L engines, tighten the bolts in sequence, as follows:
   1. Step 1: Bolts 1-10 to 22 ft. lbs. (29 Nm).
   2. Step 2: Bolts 1-10 to 43 ft. lbs. (59 Nm).
   3. Step 3: Loosen bolts 1-10 completely.
   4. Step 4: Bolts 1-10 to 22 ft. lbs. (29 Nm).
   5. Step 5: Bolts 1-10 plus 50-55 degrees.
   6. Step 5: Bolts 11-14 to 74 inch lbs. (8 Nm).
      
      Fig. Cylinder head torque sequence-1.8L engine
      
      
      Fig. Tighten the valve cover bolts in sequence-1.6L and 1.8L engines
      

Here you go, I hope this is what you were looking for:

For 1987-94 models, the cylinder head bolts are tightened in 3 progressive steps. Tighten them in the proper sequence as follows:
Step 1: 50-55 ft. lbs. (68-75 Nm) Step 2: 60-65 ft. lbs. (81-88 Nm) Step 3: 70-85 ft. lbs. (95-115 Nm) Let me know if I can assist you with anything else.