Question about 1999 Chevrolet Blazer

1 Answer

4x4 does not work was told encoader motor where is it located

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 76,846 Answers

It is on the back of the transfer case under the car at rear of transmission

Posted on Sep 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the 4x4 relay located?


Jazmin,

I sure can help you - I need the Year, Make, and Model to help you. See me at https://www.autorepairhelp.us for more help in repairing your car, truck, or SUV.

Regards,

Master Tech Lee

Dec 07, 2014 | Cars & Trucks

2 Answers

Can i change out a 1999 chevy 4x4 blazer motor with a 1997 jime 4x4 motor?


you will probably have a few sensors where the plugs might be different but other than that you should be able to

Feb 18, 2013 | 1999 Chevrolet Blazer

1 Answer

97 GMC Sierra electronic 4x4 problem


check the vacuum lines for cracks bend them a little when doing so to expose any hidden cracks make sure the end is on good.

Apr 17, 2017 | 1997 GMC Sierra

1 Answer

Where are the fuses for the 4x4 located on a 05 envoy


This not a fuse problem. When you switch to A4WD or 4HI, do the indicator light for those positions stay on solid or do they blink and then return to 2HI position? If so, then there is probably a problem with the transfer case actuator/motor.

Aug 10, 2012 | 2005 GMC Envoy

2 Answers

The 4x4 is not working on my jimmy. I already replaced the swithc that goes on the dashboarda and still not working. Any ideas??


Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

Dec 08, 2009 | 2000 GMC Jimmy

2 Answers

I have an 86 toyota 4x4 with the 22r motor. my


it could just be the switch,, or more likley to be the resistor burned out or the reostat? (same thing realy)

Oct 27, 2009 | 1986 Toyota Pickup 4WD

3 Answers

4x4 does not respond at all on 2001 ford Ranger Edge


I have a 2001 Ford ranger edge 4x4 with the 4.0L SOHC. My 4x4 module had to be replaced before I bought the truck used. The previous owner said the module was located behind the plastic panel that is under and to the right of the glove box. Mine makes a clicking noise whenever I turn the switch to 4x4 or 4x2. That's just the solenoid switch that is inside the module working. From what I've heard it's pretty common for the modules to get corroded from moisture over time in that location. Hope this helps. God bless

Sep 17, 2009 | 2000 Ford Ranger SuperCab

1 Answer

4X4 Not working


usually it is the shift motor on the transfer case. do the 4x4 lights come on when first started?

Jul 11, 2009 | 2002 Ford Explorer

2 Answers

Where is the 4x4 encoder motor sensor located on my 03 sierra


the encoder motor sensor is inside the encoder motor. the encoder is located at the transfer case. Remove the encoder and by part number 88962315 this is the sensor. you will have to retime the motor after
hope this helps

Feb 16, 2009 | 2003 GMC Sierra

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...