Question about 1992 Toyota Land Cruiser

Open Question

2002 Sienna key won't turn, steering column not locked in place, doors will not lock (they lock but pop right back to unlock position). anti-theft red light flashing

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 840 Answers

SOURCE: 99 sienna pwr door lock malfunction

no/ its the lock actuators that need to be replaced/ Please rate my response thank you very much

Posted on Feb 01, 2009

  • 1 Answer

SOURCE: Isuzu Trooper anti-theft alarm

i put a new stereo in my 1998 isuzu trooper now the anti theft wont let car start what do i do

Posted on Feb 28, 2009

  • 1 Answer

SOURCE: 2002 Tahoe steering column wiring problems

The wiring harness that run the multifunction swith has broke. I took my column apart and soldered the wires back together for the mean time. I dont suggest tring to do that its not a good fix. i found your post looking for the harrness. If you disconnect the battery you disconnect the airbag system

Posted on Mar 03, 2009

  • 1 Answer

SOURCE: 2005 Toyota Sienna Sliding Door Won't Open

Have 2005 Sienna and its Driver side door was not openning. Cheap dealer fixed it himself in front of me. After opening the doors plastic assembly while sitting inside with a screw driver. Then he bent the clip towards left where the metal wire is connected. If you guys want to see what he did i would record a video and upload for you guys. Let me know at xahid2000@yahoo.com

Posted on Mar 13, 2009

  • 92 Answers

SOURCE: Help me with my anti theft problem...........please

no the alarm is connected to the cars main computer.and needs the correct signal to start the car.

Posted on Mar 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where Is the anti theft module


Passive Anti-Theft System (PATS) Transceiver module is around the key lock cylinder behind or under the plastic cover on the upper steering column'
Passive Anti-Theft System (PATS) Transceiver Removal
  1. s4h~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
    Disconnect the battery ground cable, Refer to Section 414-01
  1. Remove the ignition switch lock cylinder.
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
    2. If equipped, remove the tilt wheel handle.
    3. Remove the upper and lower steering column shrouds.
      1. Remove the screws.
      1. Remove the upper and lower steering column shroud.
      2. Remove the lower instrument panel steering column cover.
        1. Remove the screws.
        1. Remove the lower instrument panel steering column cover.
        2. Remove the instrument panel steering column opening cover reinforcement.
          1. Remove the bolts.
          1. Remove the instrument panel steering column opening cover reinforcement.
          2. Remove the anti-theft transceiver module.
            1. Remove the screw from the bottom of the transceiver module.
            1. NOTE: Only apply pressure or leverage below the key cylinder lower rib.
              Disconnect the electrical connector and remove the module.

Dec 24, 2014 | 2006 Ford Taurus

1 Answer

Gear position indicator modulator


I have a 1999 Sienna toyota but my flickering light when car on..

Jan 05, 2014 | 2002 Chevrolet Silverado 1500

1 Answer

I can't get the rod that connects the key lock and door latch in the right position to work correctly.


  • Disconnect the negative battery cable with the proper size wrench and place away from the battery.

    Insert the key into the ignition lock cylinder and turn the key to the run position.
  • 2 Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
  • 3 Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.

    Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.
  • Installation
  • 1 Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
  • 2 Install the electrical connector back into the connector housing by pressing it in with your hands.
  • 3 Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
  • 4 Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.


  • hope this helps you

    Dec 21, 2010 | Ford F-350 Cars & Trucks

    1 Answer

    How Do I Reset A Mercury Villager/Nisan Quest Minivan 1997 Anti-theft Feature? I've locked and unlocked the vehicle several times, but it doesn't reset. That is, the ignition and steering column remain...


    U HAVE ALREADY DONE THE RESET, IF THAT DOESN'T RESET IT THEN THE SYSTEM HAS A DEFECTIVE PART. SOUNDS LIKE THE DOOR LOCK SENOR IS DEFECTIVE ON THE DOOR LATCH INISDE THE DOOR.

    Jul 04, 2010 | Nissan Quest Cars & Trucks

    1 Answer

    How do you replace ignition switch for 2002 mercury cougar?


    unless you have access to a scantool with anti-theft security access you won't be able to replace it your self you will have to go to a local repair shop. if you have access to one then
    Functional Lock Cylinder

    1. Disconnect the negative battery cable.
    2. Remove the upper and lower steering column covers.
    3. Turn the ignition lock to the accessory position.
    4. Insert a 0.125 (3.17mm) wire pin or small drift punch in the hole at the top of the cylinder housing and depress the retaining pin while pulling out the lock cylinder.
    To install:
    1. Turn the new lock cylinder to accessory position and while pressing the retaining pin in, insert the lock cylinder into the housing.
    2. Turn the key to the OFF position the release the retaining pin.
    3. Try the lock cylinder operation in all positions.
    4. Reinstall the steering column covers.
    5. Reconnect the negative battery cable.

    hope this helps.

    Mar 12, 2010 | 2002 Mercury Cougar

    1 Answer

    The key on my 2003 hyundai 35oxg will not turn.


    it has a anti theft locking steering wheel column you have to put the key in then turn the string wheel to the left or right hard and while still holding the steering wheel turn the key. and next time fyi if you turn the steering wheel after the key is not in the ignition it will lock to prevent theft.

    Dec 07, 2009 | Hyundai Motor 2005 XG350

    2 Answers

    Need another key for Anti-Theft Steering Wheel Lock


    call the company there the only ones that can get you that key

    Sep 29, 2009 | 1990 Volvo 740

    1 Answer

    Turned the steering to unlock the ignition. Then the steering locked up. This is perhaps an anti-theft lock? Now I can't start the car with the correct key. How do I unlock the ignition and steering...


    IF YOU HAVE THE PROPER KEY AND IT IS NOT DAMMAGED BOTH SHOULD RELEASE WITHTHE TURN OF THE KEY... MIGHT HAVE TO WIGGLE THE STEERING COLOUM BACK AND FORTH SOME BUT THEY SHOULD HAVE RELEASED

    Sep 01, 2009 | 2004 Pontiac Vibe

    1 Answer

    How do I remove the ignition lock cylinder from the steering column on a 1978 Jeep CJ7. I already have the steering column disassembled.


    here are the instruction the first set are the instruction on how to remove the turn signal switch as you will need them to remove the ignition

    Removal & Installataion of turn signal switch
    1. Disconnect the negative battery cable.
    2. Remove the steering wheel.
    3. Loosen the anti-theft cover retaining screws on 1976 models and lift the cover from the steering column. It is not necessary to completely remove these screws.
    4. Depress the lockplate and pry the round wire snapring from the steering shaft groove. A lockplate compressor tool is available for compressing the lockplate.
    5. Remove the lockplate, directional signal canceling cam, upper bearing preload spring, and thrust washer from the steering shaft.
    6. Move the directional signal actuating lever to the right turn position and remove the lever.
    7. Depress the hazard warning light switch and remove the button by turning it counterclockwise.
    8. Remove the directional signal wiring harness connector block from its mounting bracket on the right side of the lower column.
    9. On vehicles equipped with an automatic transmission, use a stiff wire, such as a paper clip, to depress the lock tab which retains the shift quadrant light wire in the connector block.
    10. Remove the directional signal switch retaining screws and pull the switch and wiring harness from the steering column.
    11. Guide the wiring harness of the new switch into position and carefully align the switch assembly. make sure that the actuating lever pivot is correctly aligned and seated in the upper housing pivot boss prior to installing the retaining screws.
    12. Install the directional signal lever and actuate the directional signal switch to assure correct operation.
    13. Place the thrust washer, spring, and directional signal canceling cam on the upper end of the steering shaft.
    14. Align the lockplate splines with the steering shaft splines and place the lockplate in position with the directional signal canceling cam shaft protruding through the dogleg opening in the lockplate.
    15. Install the snapring.
    16. Install the anti-theft cover.
    17. Install the steering wheel and connect the negative battery cable.
    18. Check the operation of the turn signal switch.

    Removal & Installation of ignition lock switch
    1. Disconnect the battery ground cable.
    2. Remove the turn signal switch as described earlier in this section. You don't have to remove the switch completely, just set it aside.
    3. Insert the key. Position the key as follows.
      • 1976-83: With manual transmission, put it in the ON position; with automatic, put it in OFF/LOCK.
      • 1984-86: Two detent positions, clockwise, beyond OFF/LOCK.
    1. Working through the slot next to the turn signal switch mounting boss, use a thin screwdriver to release the lock cylinder.
    2. To install, insert the key in the new lock cylinder. Hold the sleeve and turn the key clockwise until it stops. Align the cylinder retaining tab with the housing slot and insert the cylinder. Push the cylinder in, rotate to engage, then push in until the retaining tab engages the housing groove.
    3. Complete the procedure in the reverse of removal.

    Aug 20, 2009 | Jeep CJ7 Cars & Trucks

    1 Answer

    Car won't start


    Hi, does the alarm shut off when you unlock the passenger door?
    If it does not I will give you a test that you can do.
    1. disconnect the harness anti-theft control module. (loctaion depend were you live USA next to fuse panel Canadian models above the glove box.) Check the continuity between Light Green/Black wire and Black wire of the anti-theft control module.
    2. Continuity should not be there with the door lock in, lock or neutral position. With the door lock in-between lock and neutral position (any door) continuity should be present.
    3. If continuity is as specified replace the anti-theft control module. If continuity is not as specified, check operation of the door lock switches.I will add that test at bottom.
    4. If the door lock switches are ok check the continuity og LIGHT/BLACK wires between anti-theft control module and door lock switches. Check Continuity of BLACK wire between door lock switches and ground. Continuity should be present if Continuity is not present repair harness or connectors.
    5. If Continuity is present, check continuity LIGHT GREEN and BLACK wire of anti-theft control module. Continuity should not be present with trunk lock in lock or neutral position. With trunk lock in-between lock and neutral position, Continuity should be present.
    6. If Continuity is as specified replace anti-theft control module. If Continuity is not as specified, check operation of truck lock switches. If necessary replace trunk lock switch.
    7. If trunk lock switch is ok, check Continuity og LIGHT GREEN wire between anti-theft control module and trunk lock switch. Check Continuity of BLACK wire between trunk lock switch and ground. Continuity should be present. If Continuity is not present repair harness or connectors.

    DOOR LOCK SWITCHES
    Disconnect 4-pin door lock switch connect (left and right front doors) With door lock in neutral, full lock or full unlock position, there should be no continuity between any terminal and BLACK wire terminal. Continuity should exist between LIGHT GREEN?WHITE wire and BLACK wire terminals with door lock in-between neutral and full lock position. Continuity should exist between LIGHT GREEN/BLACK wire and BLACK wire terminals with door lock in-between neutral and full unlock positions. If continuity is not as described, replaced door lock switch.

    Hope this help its a place to start. let me know if you need anything else.

    Cheers

    Aug 23, 2008 | 1994 Nissan Maxima

    Not finding what you are looking for?
    1992 Toyota Land Cruiser Logo

    Related Topics:

    103 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...